Question about 2008 Chrysler Town & Country

1 Answer

Chrysler 3.o v6 engine cannot reach above 4000rpm

Already replace a recommended chrysler spark plugs but cannot reach above 4000rpm what could be the possiblke problem?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 308 Answers

Possible broken valve springs, well known for this problem. check compression..

Posted on Dec 12, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how do I change the

I did a Google search "How do you replace the rear spark plugs on a 2000 Chrysler Cirrus?" and found this link: http://www.faqs.org/qa/qa-6243.html

I haven't tried it yet and am thinking of purchasing a Chilton manual just in case, but as far as explanations go the one at the very bottom of the page in the link sounds the most legitimate so far.

Besides, I have to pay you guys $9.99 for one answer that I can get for free; or I can get the Chilton and have a whole heap of answers for around $20.

Posted on Jul 14, 2008

  • 2 Answers

SOURCE: Tune up on cown and country (chrysler)

I just changed the rear spark plugs on my 1997 Chrysler Town & Country this weekend. It took me about 7 hours to do everything. When you replace the rear spark plugs, its a good item to replace everything i have listed below. Listed below are the items i changed while i was in there:

Valve Cover Gaskets
All 6 sparks (the rear are the hardest) I used the Bosch Plat. +4
Intake manifold gasket (only cost $3-4)
Throttle body gasket.
Air filter
Spark Plug Wires

I also bought some throttle body cleaner and sprayed the throttle body to clean it out. When the throttle body is dirty your van can stall.
I took pictures of everything i took apart, which i can email you to help you out.

Thank You,
Nip
Highhrider@aol.com

Posted on Sep 23, 2008

  • 15 Answers

SOURCE: how to change spark plugs on 2000 chrysler grand

use a lift, let van cool or change front three while van is cooling and from the under side of the engine change the other last three. They can be reached easily. No need to remove plenium.

Posted on Jul 08, 2009

  • 148 Answers

SOURCE: how do you replace spark plugs on a 1996 chrysler

You will have to remove the upper intake manifold to replace the rear plug.There are no shortcuts ,and besure to replace the upper intake gasket as well.

Posted on Jul 28, 2009

1fastbob
  • 301 Answers

SOURCE: oil in 1 1997 chrysler lhs spark plug tube

although I am not familiar with this particular engine my son's Mazda Miata had oil in the plug holes and it only required a new valve cover gasket to fix it.

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

When do spark plugs need changing on a 2008 4.5 XJ8 Jaguar


only when there is a problem as reported by the fault codes. With engines controlled by the ECM the voltages that are required to operate spark plugs is very high ( in excess of 60.000 volts) This in turn means that the current flow across the electrodes of the plugs is minimal and so the electrodes do not burn as they did in years gone by. There are manufacturers today that fit v6 engines in the engine bays where the rear 3 plugs cannot be easily reached and so they fit platinum plugs and recommend that they never be changed. It really is a preference thing but as the ECM continually tunes the engine (hundreds of times a minute) tune ups are basically a thing of the past and any problems will be recorded in the fault codes.

Feb 26, 2015 | 2008 Jaguar XJ8

2 Answers

Spark plug replace


Not know vehicle in Aust. but if it is a V6 the rear plugs should be titanium and good for 100,000 miles

Dec 10, 2012 | Chrysler TC Cars & Trucks

1 Answer

2002 ford escape.....truck started sputtering and would not accelerate very fast and check engine light started blinking. what could it be?


I have an 2002 Escape with a 3.0L engine.
First you need to get a OBD2 scan for the check engine code.
I suspect the code will tell you that one of the cylinders is misfiring.
If you also have the V6 engine, the most common cause of misfire is one of the Coil-Over-Plugs (COP). Each cylinder has a COP on the spark plug.
On the V6, you need to remove the upper intake manifold to get the back 3 COPs.
If you have a V6, and you have cylinder misfire, I recommend replacing all the plugs and coils.

I have had 2 COPs go bad. The second time, I replaced all of them.

Removing the intake is fairly easy if you have some repair experience. You need to get an intake gasket set for about $10-15.
The coils run +$75 each for OEM. I went with Ebay aftermarket; 6 coils for about $80.
I recommend replacing the plugs with the exact same brand as original. There is no miracle plug that will give you better performance or mileage. Stay original.

Feb 21, 2011 | 2002 Ford Escape

1 Answer

Car keeps giving p0303 code.


Code P0303 means that there is a misfire detected on cylinder #3. This could becaused by anything from a worn out spark plug to a blown cylinder head gasket, a faulty fuel injector, a bad ignition coil, or a leaking intake manifold gasket. I have also seen this type of code caused by clogged-up EGR ports in the intake manifold on certain engines. "Freeze Frame Data" stored in your Engine computer along with the fault code is designed to help identify what engine conditions (high speed/slow speed, heavy load/light load, etc.) are producing the misfire. This helps a lot in identifying exactly what is causing the cylinder to misfire.

One way to eliminate some of the possible causes is to swap parts with another cylinder to see if the code changes.

If you have "Coil-On-Plug" ignition, you can swap the coil on #3 cylinder with the coil on #4 Cylinder and swap the #3 spark plug with the #2 spark plug. Then clear the codes and drive the car till the Check Engine (or Service Engine Soon) light comes back on.

If it still gives you P0303, then it is not being caused by the plug or the coil. It could be any of the other possible causes listed above.
If it now gives you P304, replace the bad ignition coil that is now on #4 cylinder.
If it now gives you P302, Then replacement of all the spark plugs is recommended.

Dec 26, 2010 | Chrysler PT Cruiser Cars & Trucks

1 Answer

I just reached the 100,000 mile mark. Any


Hello, according to Snap-On / Shopkey / General Drivers,
For your 2004 Ford Taurus:
1. Inspect Accessory Drive Belt 2. Perform Multi-Point Inspection (Recommended) 3. Replace Engine Coolant 4. Replace Engine Oil 5. Replace Engine Oil Filter 6. Replace PCV Valve 7. Replace Spark Plugs 8. Rotate Tires.
This is going by the general consensus from Snap-On tools and Ford Motor Co. Hope this helps :)

Nov 21, 2009 | 2004 Ford Taurus

1 Answer

How do you change Spark plugs for an 05 Chrysler Pacifica and where is it located?


is it a DOHC V6 if so ur in luck their is probably a plastic cover on the engine remove that to gain access to the valve cover on the front bank. The spark plugs should be right in the center of the valve cover you'll need to get a 6" or so extension to reach down into the cylinder head to remove them the same steps for the spark plugs on the back bank (closest to the fire wall).

Oct 13, 2009 | 2005 Chrysler Pacifica

1 Answer

How to change spark plugs on 2000 chrysler grand voyager v6 3.3l


use a lift, let van cool or change front three while van is cooling and from the under side of the engine change the other last three. They can be reached easily. No need to remove plenium.

Jul 08, 2009 | 2000 Chrysler Grand Voyager

2 Answers

Spark plugs


You have to remove the intake (and the manifold) just to get to them. They are on the engine like every other car but access is trying because you can't even see them until you start removing the above items. If you still aren't sure where all of this is, follow the plug wires from the coil pack to the plugs. If it does not have wires, it will have individual coils on top of each plug. Unbolt each coil and pull it up. The plug is under it. On your V6, they should be located on the side.
This is very tricky on this vehicle. It is, of course, recommended to take it to a shop. Some special tools may be required.

Apr 30, 2009 | 2003 Mazda Tribute

2 Answers

Can't find all spark plugs


Well seeing as u don't specify the year or engine u have in ur monte carlo, it's kinda har to tell u where they are.If it's a V6, the 3 rear sparkplugs are behind the engine under the manifold. Most times the rear engine mount must be removed and the engine preid to reach the sparkplugs from underneath.

Good luck.

Sep 09, 2008 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...