Question about Cars & Trucks

1 Answer

How do I program my key fab on my 1997 Chevy s10

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

Trick you have to hold it you will her 3 beeb and if you use numbers code are 0000or1234or some time 5

Posted on Dec 12, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 634 Answers

SOURCE: 1997 Chevy S10 A/C not cooling. Fan blows

sounds like the airbox doors are not working these are located behind the dash passengers side, a chiltons manual availible at most parts stores for around $25 will give you diagrams and steps to access this area if u need that help

Posted on Jul 08, 2009

  • 740 Answers

SOURCE: 1997 Chevy S10 pickup Fan switch for heater runs on high only.

replace the blower motor resistor located on the heater box were the blower motor is located the wiring to the blower may go to it. This is very easy to locate if you buy the part first.

Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1997 Chevy s10 blazer with a 4.3 v6 will a 1998 Chevy s10 blazer 4.3 v6 interchange


they should swap just fine. 1996 and on are interchangeable. 1995 could go either way. 1994 and older are interchangeable.

Apr 23, 2016 | Chevrolet S 10 Cars & Trucks

1 Answer

I have an Ultrastart (model UTX4, thats either the key fab model or remote itself) remote car starter. I changed the battery in key fab, light does not come on on fab. I seem to remember a code is nee


I had the same problem. you have two choices. 1-Go to an auto parts store and buy a new one, and then try to program it yourself. 2-Take your key fab to a Ford dealer and either have them reprogram the original or buy a new one. Sorry, but that's the only solution I have found.

May 19, 2014 | 2003 Ford Expedition

2 Answers

Cant seem to locate Drivers and passengers side Headlight assembly for 1997 Chevy S-10, 3door, 6 cyl.


even at a salvage yard? go to RCSR.com (Rancho Cordova Specialized Recyclers) and get their 800 number, tell them that a 928 Porsche guy from Tahoe sent you to them and I will bet they can ship the part to you in three days for a good price...if you mean locate in the engine compartment try removing the headlight first...

Oct 03, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

1997 chevy s10 blazerdash wont light up when key


the dash sound's like a fuse, check the fuse box under the hood and in the door jamb on the side of the dash, also check your fuel filter and fuel pump, im betting on the pump because i have a 2001 chevy blazer that has had two replaced and it has 233000km on it!

Jun 04, 2010 | 1997 Chevrolet Blazer

1 Answer

1997 Chevy S10 pickup Fan switch for heater runs on high only.


replace the blower motor resistor located on the heater box were the blower motor is located the wiring to the blower may go to it. This is very easy to locate if you buy the part first.

Jan 06, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

Keyless entry wont work 2002 chevy s10


The only way to program them is with a scan tool so you'll need to visit your local dealer to have it done. Here is how it is done.

  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool. Important: The scan tool must stay connected until all of the transmitters are programmed.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.

Sep 02, 2009 | 2002 Chevrolet S-10

1 Answer

1997 Chevy S10 A/C not cooling. Fan blows


sounds like the airbox doors are not working these are located behind the dash passengers side, a chiltons manual availible at most parts stores for around $25 will give you diagrams and steps to access this area if u need that help

Jul 08, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Cannot remove key from ignition or move shifter out of park


i've had this problem before. it is more then likely the ignition switch. if the key gets stuck like you say

Dec 28, 2008 | 1997 Chevrolet S-10 Pickup

3 Answers

I have a 97 Chevy S10 pickup...cannot move shifter out of park


When my battery was dead i was forcing the key in the ignition which messed everything up with my chevy s10 and have to get everything replaced....: (

Dec 28, 2008 | 1997 Chevrolet S-10 Pickup

2 Answers

No tail lights


Try checking the headlight switch it may have broken contacts in it. Easy fix go to a salvage yard find same make and model truck, swap headlight switches.

Dec 27, 2008 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...