Question about 2001 Chevrolet Tracker
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
When bleeding brakes after the system has been opened for service (you didn't say if you were doing any work on the master cylinder) you should start with the farthest wheel away from the master cylinder, which is the righ rear. Fill the master cylinder, then have an assitant "pump up" the brake pedal. Tell them to hold it down firmly, then open the bleeder on the wheel cylinder(s). Do not release the brake pedal until you have closed the bleeder valve again. You'll know when the air is out - there won't be any more bubbles. Since this vehicle is 2001, this would be a great opportunity to flush the system. Just make sure you have enough brake fluid (DOT 3 or 4, depending on your vehicle). Good luck!
Posted on Mar 15, 2009
SOURCE: 2001 chevy tracker
Hi,If you are mechanicly inclined replacing the timing belt should be simple ,If the car still runing be sure to aling the timing marks perfect and make a note of the position in a piece of paper,If not you can get the specs at the auto parts where you get the belt ...YES they can jump do to wear and they can cause valves to bend ,this can also cause major engine damage....
Posted on Aug 17, 2008
i have done a few timing chains, you should go get a manual so you can go back and reference when you need to. I can tell you this "do not" move the cam or crank when the belt or chain is off. Hope it helps
please rate answer
Posted on Mar 21, 2009
you will need a friend to help you for this
Buy some new brake fluid, about 500ml should be enough
you can buy some clear plastic tube with about a 3mm hole through it, 300 to 400mm long or 1ft to 1ft 4inches, put one end of the tube into a small jar or something to catch the fluid when it comes out of the bleeder valve
find the bleeder on the disc caliper and also on the backing plate of the rear wheels unless it has rear disc brakes as well, slip the other end of the plastic tube over the bleeder screw
top up the brake fluid in the resevoir
get you friend or whoever to pump the brake pedal
while you put the spanner on the bleeder screw
tell your friend to push down on the pedal
loosen the bleeder screw about half a turn until the brake fluid starts to come through the plastic tubing
your friend has to keep the pressure on the brake pedal as it will go to the floor when you open the bleeder
once it has been pushed to the floor tell your friend to hold it down while you close the bleeder screw
once you have closed the bleeder screw he or she can pump the pedal up again until it goes hard
repeat this process until there is a good flow of fluid coming through with no air
check the brake fluid resevoir several times during this process to make sure that is not empty because if it is empty you will have to start the process all over again
repeat this process for all 4 wheels
hope this has helped
Posted on Jul 04, 2010
Tips for a great answer:
Sep 29, 2016 | 2001 Chevrolet Tracker
Mar 26, 2016 | Cars & Trucks
Aug 23, 2015 | AC Cars & Trucks
Sep 29, 2014 | 2001 Chevrolet Tracker
Oct 14, 2013 | 2001 Chevrolet Tracker
Jul 12, 2011 | 2001 Chevrolet Tracker
Aug 24, 2010 | 1999 Chevrolet Tracker
Feb 16, 2010 | 2001 Chevrolet Blazer
Dec 31, 2009 | 2001 Chevrolet Tracker
Apr 04, 2009 | 1999 Chevrolet Tracker
331 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: