Question about Mitsubishi Pickup

Open Question

Valve clearance for misubishi L300

Cold engine

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 46 Answers

SOURCE: valve clearances

On the intake 0.0008 or 0.0020 (it's in between these 2)

this is for the stem to guide clearance. (for the intake)

The Exhaust 0.0018 to 0.0030 stem to guide clearance.

Posted on Jul 14, 2008

moparownr
  • 667 Answers

SOURCE: 96 escort valve clearance

Gary, the 1.9L Ford engine has hydraulic lifters no valve adjustment is needed

Posted on May 18, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: noisy startup when cold, sounds like valve

Hello onarock844...The Hyundai 2.4 litre and the 3.3 litre are known to have valve train noise. Some sooner than others.
The timing chain tensioners on the 06 and 07 Sonata 3.3 engines built before August 4, 2006 are well known for developing wear that allows them to make a tapping or rattling noise for a short time after a cold start. This noise can be mistaken for a lifter noise, although the actual source is in the front cover area of the engine. Hyundai has released a technical service bulletin on this problem, which describes installation of an updated design timing chain tensioner (part #24410-3C300) to correct this noise issue.
Ask your dealer to refer to Hyundai service bulletin #06-20-002 for information...If this has already been corrected,,,and the noise is coming from the upper engine area and not from the timing chain area, then the valve clearance will need to be adjusted. This is done by disassembling the valve train and installing slightly different size tappets to change clearance.
This is a fairly labor intensive process, so if you are still under factory warranty then you will want to go over the dealer's head and get the Hyundai zone rep involved to get it covered before your warranty coverage expires...
I recommend useing a full synthetic engine oil, i know in a few cases where the noise has stopped when the oil was changed over to synthenic, also a high quality filter is important, such as a purolator.
Good luck...i hope this helps...please rate me a fixya.

Posted on Jul 29, 2009

superjorge1
  • 8 Answers

SOURCE: what is the valve clearance in the 1993,1500cc

there is a white sticker underneath on the bottom side of your hood that should give you valve clearance specs.

Posted on Nov 14, 2009

michigan man
  • 3533 Answers

SOURCE: valve clearance of 12 valve engine

i do not know but give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the valve clearance of nissan caravan


Valve lash is the end of the rocker arm and the valve stem clearance between. When the engine is running, due to the thermal expansion and contraction, if there is no gap between the rocker arm and the valve stem, rocker arm swells, the top valve open, the impact of engine power and economy. Engine valve clearance will be different, usually when the car is cold, the intake valve 0.08-0.10MM, clearance exhaust valves 0.10-0.12MM Car Diagnostic Tool

Aug 26, 2016 | Nissan Cars & Trucks

2 Answers

1996 honda will not start under 60 degrees


tune it up. (fresh spark parts work best in cold and for sure damp wheather.
fresh gas?
leaking injectors?
isc stuck closed, and rpm low, hot?

the ecu, anticipates the next cold start,
it knows how much to open the iSC valve, to get a good start cold
and if colder to day, it opens more. (math)
if it (ISC) is gummed up,fas all do, it cant start right
so next time, try %10 throttle, starting, emulating a good ISC.
see?

Jan 07, 2014 | 1996 Honda Accord

1 Answer

How to adjust mitsubishi l300 valve clearance


if hot engine.what is the valve clearance?

Jan 05, 2013 | Cars & Trucks

2 Answers

Valve clearance 4g13


make the engine runs for about 30minutes before adjusting the valves,
valve clearances:
intake valve = 0.20mm(0.008 in)
exhaust valve = 0.25mm(0.010 in)
for reference only when the engine is cold,
valve clearances:
intake valve = 0.25mm(0.010 in)
exhaust valve = 0.30mm(0.012 in)
engine specs: mitsubishi 4g13 1.3L (if you have same engine)

Feb 29, 2012 | Mitsubishi Cars & Trucks

2 Answers

What are the valve clearance specs for a 1996 Toyota T100 v6?


you should get haynes auto repair manul for your particular car that way you will have the correct information about that. you can get the manul at autozone or any autopart, all you need is your car info, to pick the right manual for your car, good luck

Jul 15, 2011 | Toyota T100 Cars & Trucks

3 Answers

Valve clearance 4hj1 isuzu engine


This is the specs for the 4H Diesel engine:
Intake valves clearance cold 0.4mm(.016inches)
Exhaust valve clearance cold 0.4mm(.016inches)

Jan 28, 2011 | 1995 Isuzu Pickup

1 Answer

What is the difference between hot and cold vavle clearances


When it is stated that valve clearance should be set when hot, you first adjust the clearance on the cold engine after assembly to the hot setting specs if they are the only ones given, then let the vehicle warm up to operating temperature. Then adjust the clearances again.
If it is just a tune-up(undisturbed engine), let the engine warm up to operating temperature, then adjust.
The reason is that metal expands as it heats up, which affects the valve clearance.

Dec 05, 2010 | Toyota Land Cruiser Cars & Trucks

1 Answer

Valve Clearance


valve clearance, with engine hot, intake valves are .005-.006 in, exhaust valves are .011 in, if engine is cold then its intake .009-.011 in and exhaust is .007. hope this helps good luck.

Nov 28, 2009 | 1989 Suzuki Swift

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...