Question about 1999 Mazda Protege

Open Question

Mazda familia 1998 abs fault codes

What is abs fault code 48

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: mazda tribute abs fault. abs

These vehicles have a recall on the ABS system for faulty wiring. You may want to check with your local dealer to see if your vehicle is included.

Posted on Sep 20, 2008

  • 1 Answer

SOURCE: ABS, Traction control and handbrake

I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on but speedometer was not functioning and the ABS light was on. The rear ABS senssor was the problem.
SDM

Posted on Jan 23, 2009

AEpgh
  • 51 Answers

SOURCE: 1989 Mazda 323 gtx BG

Two things...
You should follow the pin numbers and not the color code.
Second
Check online for a service manual from Japan or the USA for that car. We got many Mazda imports here and there should be a lot of books on Ebay that would have the electrical schematics for a 323 from the USA and Canada.
You are going to have to just buy a book and have it shipped to NZ.

Posted on Mar 04, 2010

tunde007
  • 2382 Answers

SOURCE: Mazda 626 (Capella) ABS fault. I

Hi,
Code 44
Oxygen sensor voltage was under 0.25 volts for up to 4 1/2 minutes of closed loop operation, lean exhaust. Check the ECM wiring connections. Check for vacuum leaks at the hoses and intake manifold gasket.

Code 48
Misfire Diagnosis. Check the ignition and fuel systems.

Posted on Jan 31, 2011

bayyagg
  • 1672 Answers

SOURCE: How much oil to put

3.5 liters would be the proper ammount of oild needed in the engine, plus the oil cartridge.

Posted on Apr 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes ABS light to stay on continuously


You will need to get the fault codes read as the fault can be any of the following
abs sensor fault
wiring fault to any of the sensors
abs ring lost teeth or read fault
abs controller self test fault
abs pump fault
brake line not holding pressure slight leak

Feb 01, 2017 | Cars & Trucks

3 Answers

Abs brake problems


Its a sensor that needs changing, Even if the resistace is ok, dosent mean its pulsating and sending the correct signals.,, you already know the problem, the solution is you have to change the sensor.

Aug 01, 2008 | 1990 Buick Reatta

2 Answers

2003 Durango abs light won't go off nothing is wrong no codes are thrown


If that light is on there is a code, you did read this with an ABS capable scan tool? an engine code reader tool will not read the ABS control module

Dec 02, 2016 | Cars & Trucks

1 Answer

How do I obtain a list of the ABS fault codes/ definition and diagnostic procedures


Try this: https://www.youtube.com/watch?v=Tf9ygGnJ-6o But there is not a lot of information on brake systems because of the liability and royalties that are involved.

Feb 25, 2015 | Cars & Trucks

1 Answer

Abs on vr commodore light stays on solutions


Error logs are a great thing. They will help you find intermittent problems and start you off in a general direction of where a problem could be. There is a great level of detail on the justcommodores site on checking error codes logged by the engine management system, but this does not detail anything about the abs system. The abs warning light is not as common as the check engine warning light. Reading through the posts, I haven't found any detail on checking error codes logged by the abs system.

So here it is. For those of you familiar with checking the engine error codes, this procedure is so simple its not funny.

Basically, to check the engine error log, you bridge the 5th (ground) and 6th pins in the ODB connector under the steering wheel.

To check the ABS error log, using the same trusty calibrated paper clip, you simply bridge pins 5 and 12 of the connector.

To find pins 5 and 12, start at the top left hand corner. That is pin one. Going to the right, you count pin 2,3,4 etc. Once you get to the end, jump back to the start of the bottom left level of pins and keep counting. Pin 5 is about halfway along the top row, pin 12 is a little left of the middle in the bottom row.

Reading the error codes is the same procedure (counting the flashes), except now, the ABS light flashes (as opposed to the engine light when checking the engine codes).

The ABS log also uses code 12 firstly, with any errors logged shown after that. If no errors are logged, the 12 will flash again.

Error codes for the ABS error log (VR/VS) are as follows:

12 Diagnostic system operational
21 Right hand front wheel speed sensor fault
23 Right hand front wheel speed sensor continuity fault
25 Left hand front wheel speed sensor fault
27 Left hand front wheel speed sensor continuity fault
28 Wheel speed sensor frequency error
31 Right hand rear wheel speed sensor fault
33 Right hand rear wheel speed sensor continuity fault
35 Left hand rear wheel speed sensor fault
37 Left hand rear wheel speed sensor continuity fault
41 Right hand front inlet solenoid valve circuit fault
42 Right hand front outlet solenoid valve circuit fault
45 Left hand front inlet solenoid valve circuit fault
46 Left hand front outlet solenoid valve circuit fault
55 Rear inlet solenoid valve circuit fault
56 Rear outlet solenoid valve circuit fault
61 Pump motor relay circuit fault
63 Valve relay circuit fault
71 ABS control module internal fault

The above guide has been verified on a VR/VS. Checking the error log on all models prior to VR/VS is the same for the engine log, and I would assume that the same can be said for the ABS log, would be happy if someone could verify this for me.

Sep 21, 2013 | 2005 Mazda Tribute

1 Answer

Mini abs pump motor power supply fault code 5E2D


Check and replace the ABS motor control relay.

Feb 19, 2013 | Mini Cooper Cars & Trucks

2 Answers

I repleaced all 4 abs sensor on my 1996 toyota avalon, but the abs light still on, what could be the problem?


abs light on means some fault codes stored in your car,
toyota it2 can help you clear the code and turn off the light with airbag.

May 16, 2012 | 1996 Toyota Avalon

1 Answer

Fiesta duratec 2005 Abs warning light on


Whenever the ABS module turns on the ABS light in the dash it is to alert you to the fact that a fault has occurred in the ABS system and the control module has turned off the ABS brake control, you now have regular non ABS brakes. The waring light will stay on until the fault is corrected. Since a large number of problems would cause this you must get the control module scanned to retrieve the fault code that was set in the control modules memory when it turned on the light. Once the fault code is known the process of diagnosis and repair can begin.

Feb 10, 2012 | 2005 Ford Fiesta 1.6

1 Answer

Abs light stays on I have put new brake line on new calipers because they were sticking causing brakes to get hot, thats all fixed but light still stays on.


the ABS light is on because there has been a fault detected by the ABS module. It has nothing to do with the actual braking system.

The ABS module does a self check every time you start the vehicle. If it detects a problem during that self check the ABS light will stay illuminated and a code or codes for the fault will be stored in the ABS module. Scanning the module will allow you to pull the codes and proceed with diagnosing why the fault is occurring.

The most common source of ABS problems is bad wheel speed sensors or broken wires to the wheel speed sensors. Again pulling the codes from the ABS module will narrow down the possibilities.

Once you now what codes are present post them and we will be happy to assist you further.

Apr 21, 2011 | 1998 Chevrolet S-10 Pickup

1 Answer

FAULT CODES 32,31,48 IN ABS SYSTEM FZJ80


CODE 32- FRONT LEFT WHEEL SPEED SENSOR SIGNAL MALFUNCTION. CODE 31- FRONT RIGHT WHEEL SPEED SENSOR SIGNAL MALFUNCTION. CODE 48- OPEN OR SHORT CIRCUIT IN VTA2 SIGNAL CIRCUIT OF THE SUB THROTTLE POSITION SENSOR.

Aug 27, 2009 | 1994 Toyota Land Cruiser

Not finding what you are looking for?
1999 Mazda Protege Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...