Question about Cars & Trucks

Open Question

Codes p2oe4 p242b come up what do i need ? new sensors

2008 ford f350 6 4 codes p2oe4 & p242b comes up , do i need new sensors or repair the exhaust filter ?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 17 Answers

SOURCE: 1993 Ford Tuarus Gl IN NEED OF HELP!

Well this could be in your timing. As cars get some miles on them the timing chain stretches therefore causing you car to lose alot of power.So you may want to have your timing set on this car. Also I had a taurus that had a bad torque converter, and it lost alot of power on hills and under loads, also when i gunned the gas pedal. so try the timing first. Hopefully you dont have a bad head gasket or a cracked head these symptoms you are describing are all signs of head gaskets or blown heads

Posted on Sep 04, 2008

Ad
fastboyz
  • 674 Answers

SOURCE: check engine light

how the fuel pressure? regulator and fuel filter

Posted on Sep 10, 2008

  • 1 Answer

SOURCE: exhaust filter

Particulate filters are self cleaning. If the warning light comes on, you will need to take a long drive every so often to get the filter hot (It is a built-in part of the exhaust system.) Some models will also dump extra fuel int the system to help ignite the soot buildup and assist to "clean' the filter.
You need do nothing else; just get it really hot for a while each time the warning comes up. If you ignore it and do only short trips, it will clog up and need replacement.

Posted on Dec 27, 2008

emissionwiz
  • 76846 Answers

SOURCE: 1995 Ford Bronco 172 EGO not switching lean bank1- jerks when run

Have u checked for vacuum leaks or poss leaking EGR valve? use carb spray around the upper intake manifold where it bolts to the lower manifold, spray vacuum lines where they are connected to the engine vacuum ports, the idle speed will change if u hit a leak, as far as the EGR valve goes see if it gets hot at idle, if it does it is leaking, if all checks ok replace the O2 sensor, but i suspect u will find a leak at the upper intake plenum.

Posted on Jan 10, 2009

  • 1752 Answers

SOURCE: what would make the coce rich exhaust to come up

Replacing parts without analysis is just wasting money. You need to take it to a mechanic with the right engine analyzer.

Posted on Oct 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting error code U0414 P0118,P2060F what does that mean and what parts do I need to change for my ford escape 2008


With all these codes you need a professional to help fix this, you will likely throw parts at it and still not fix it. If you do want to try a repair at very least go on eBay and try and find a used factory repair manual set. If you google each code the explanation of the code will show, but it will only give you a system of the car, that means it can be a sensor or a part or the wiring or the computer that runs the system. Good luck

Jun 25, 2016 | 2008 Ford Escape

2 Answers

How do i fix... wrench light ford fusion 2006


You never need to top off fluids

If you do- you have a leak to be repaired

Check the vehicles systems for codes,
then google those codes to see the problem

TYPE: OBD & your code

It is going into ETC Failsafe or something

Do not use it at all,you may have converter ruining
cylinder misfires, from bad ignition coils

You add NO WATER to any vehicle

Distilled water & coolant only

Aug 25, 2014 | 2006 Ford Fusion

1 Answer

2007 ford f-350 super duty with a 5.7 l v8 codes p2198 PCM keep coming up


Why wouldn't it keep coming up

-------Your doing nothing-------

Not reading your owners manual
Not studying OBD Vehicle Systems
Not Googling your fault codes-you got the codes but do nothing

P2198 --Lack of HO2S-21 Switch -Sensor Indicates Lean

If you did the required Preventative Maintenance & replaced
the Front Oxygen Sensor BEFORE they failed at 100,000 miles,
you may not be in the situation

Every time the Emissions Monitors run, the codes come back or never left

Need a repair shop, to road test with scan tool & put a couple hours
diagnostic time into the truck & about 6 or 8 hours getting caught up
on the maintenance required

Jul 22, 2014 | 2007 Ford F-350 Super Duty XLT

1 Answer

How to repair 2008 ford F-350 diesel showing code P2033


code p2033 refers to exhaust gas temperature (EGT) sensor 2 bank 1 circuit high === causes wiring short to ground --EGT sensor . check the wiring for shorted / broken wires and replace the sensor . If there is no problem with the sensor or the new sensor fails early I would be checking the fuel settings on the pump ( pump timing and cc ratings ) as a hot diesel exhaust indicates over fuelling or pump timing too far advanced.

Jul 22, 2014 | 2008 Ford F-350 Super Duty

1 Answer

I have a 2008 Ford Escape.While I was driving , a yellow wrench appeared on the dashboard. I parked, switched it off and restarted the engine.The sign disappeared. This happened twice in two weeks' time....


The check engine light is not something new

It has been around since 1983,some 31 years

Have a shop check for codes,diagnose them &
make the repairs

I check for codes the same day any dash light appears
& diagnose things with a couple days including any repairs

Most likely you never replaced your front oxygen sensors at
100,000 miles & you have a few bad ignition coils, thus cylinder
misfires that are very very common on all fords

Mar 08, 2014 | 2008 Ford Escape

2 Answers

2003 Ford Explorer keeps coming up with P0060 Ford - HO2S Heater Resistance Bank 2 Sensor 2 i have changed the sensor 3 times and still nothing!


Why would you change any sensor more than once?

You clearly have no idea why you get an OBD2 Mil Lamp
on your dash

Codes have nothing to do with changing parts

You use the codes & diagnostic charts & professional
test equip, to find a problem & component test parts

Unless the actual problem is found & a part tests bad,
it does not get replaced

I only chose the question because no professional repair
shop would throw parts at it repeatedly.

You need a different repair shop or you need to buy the
factory ford diagnostic & emission manuals & wiring diagram
book, if you plan on work on it at home

The internet would be a good place to study that code
on your vehicle make & model

Sep 13, 2013 | 2003 Ford Explorer

1 Answer

Gas consumption sport trac 2008


Only the air filter would come into play, if you
have created vacuum leaks in the ducting & thru
unmetered air

Maybe unrelated issues you have there before

The upstream O2 Sensors could be replaced at
100,000 miles & you could look at fuel trim on a
road test

Need new spark plugs every 3 years

Clean the MAF Sensor

Dec 09, 2012 | 2008 Ford Explorer Sport Trac

1 Answer

What is the p0340 fault code & where it locatated in galant 2008


some vehicles set these codes when ignition is turned on but engine not running,
but then goto a not pressent code(history code) or no code present, when engine is running. This may be the way the system works, which with genuine scanner it may
show this but with some aftermarket scanners may only show that the code sets,
not what its status is or if its gone, it remains displayed.
So you could clear codes, engine not running, cycle ignition and if code comes back again without starting engine this is normal for this system (NO FAULT).
If it only sets again when engine has run,
is cam timming correct?
teeth on reluctor wheel all o.k. bent or dammaged?
or debris stuck to reluctor wheel?
Earth circuit could be shared with both sensors is it ok? -repair wiring or bad earth.
low Ohms reading test from sensor connector.
Is power to sensor circuit uninterupted & ok? -repair wiring

Sep 10, 2012 | 2008 Mitsubishi Galant

1 Answer

Need to reset the computer codes to the emission sensors on a 2008 Hyundai Sonata


What mechanic?

Inspection Stations have no mechanics

A state licenced repair shop wouldn't have an problem
with that.

They would make the repair & move on to pass the vehicle

No one understands, there is no resetting codes, as a fix
for anything. If that was the case, the mechanic would have done so

You can clear them & then they come back, or you
have no data to diagnose the reason they came on

A car is in no way related to window 7 or any computer
technolgy. The car has a processor called an ECM or PCM

Aug 01, 2012 | 2008 Hyundai Sonata

1 Answer

2008 Ford F450 6.4 code P0088 3 times, ( check engine light on ) dealer will clear code, and it sets code P0088 again. dealer has no fix yet ( 90000 miles )


Hello, you might try a new fuel rail pressure sensor. This Code 0088 is for high pressure at the fuelrail. It would be possible to rig a testing pressure gauge to the truck and drive it to see what the pressure really is. If the dealer has a Dyno, he could run it in the shop.

Some of the reports I am reading is the Turbo boost for other owners is starting to max out about 70-75 MPH with a load and usually going up a grade before this light comes on. A certified Pressure gauge would show whether the sensor is tripping too early.

I want to believe there are some specs the Dealer could use to bench test this sensor. But if the end result is buying a sensor and paying Labor you could just go Aftermarket and install a New sensor yourself.

Would like to know the final solution on this.

Feb 04, 2011 | 2008 Ford F 250 Super Duty 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...