Question about 1999 Lexus ES 300
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
according to the manual i have... it has three.... one in the exhaust manifold.... and two in the exhaust pipe..... slightly vauge on the exact location of the last two sensors... but looks like it is after the catylitic converter.
Posted on Apr 15, 2009
Open the deck lid (trunk) to better access the lights. There will be 2 of them. Recommend replacing both at the same time even if only one has failed. Generally sold in pairs anyway.
Directly above the license plate will be mounted 2 clear light covers. On the right side of each light cover you can see a small plastic rivet. Push in the center 1/4 inch with a small screwdriver then you will be able to pry out and remove the rivet without damaging it. This will save you from buying replacement plastic rivets for re-installation. Remove the light cover with the bulb harness attached.
The bulb harness requires a short turn counter clockwise to remove it from the light cover and the new bulbs snap into the harness. No twisting or screwing. Replace the bulb harness the same way and fasten the light cover back into place using the plastic rivet.
Saves time because both bulbs and light covers are exactly the same style, there is no left or right. Cheers!
Posted on May 11, 2009
Hello there here is a good site to give you more information and general idea of the cost involved Lexus ES Forum [Lexus Forum Archive] - Page 3 - Lexus Forums how to tell if it needs a tune up...? what is the value of my ... About how much does it cost to fix a '92 lexus ES300 with a ... 1997 Lexus ES 300 ...www.planetlexus.com/lexus-forums/archive/index.php/f-4-p-3.html - Cached
Posted on Aug 18, 2009
I had check engine light and TRAC OFF. OBD-II MIL code was P1133 which is Air Fuel Ratio Sensor Response Malfunction and scanned by AutoZone. After disconnecting the battery for 10-15 minutes, the lights went off. I cleaned the gas cap and tightened it firmly. For the last 400 miles, the lights have not come back. When scanning using Snap-on one, no code was detected. I think gas cap was the reason for the lights.
Posted on Dec 31, 2009
"To get access to the 3rd brake light:
- Place each hand against both sides of the plastic housing, and firmly grasp and pull the housing towards you. It might not budge at first, but it should move once you get a good grip on it.
- Pull the housing out just enough so that you can see the brake light bulb and stick your hand underneath. Ignore the speaker wires.
- Pull out the old bulb from the socket (it plugs in/out). Wear rubber gloves when handling the new bulb, and put the new one into the socket.
- Reverse the steps here to put the 3rd brake light back into place. Test out your brake light, and you're done" quoted from lexusk8 @ clublexus.com (great forum)
Posted on Jan 23, 2010
Tips for a great answer:
Oct 07, 2010 | 1997 Lexus ES 300
May 25, 2010 | 1997 Lexus ES 300
Apr 15, 2010 | 1997 Lexus ES 300
Aug 18, 2009 | 1997 Lexus ES 300
Apr 15, 2009 | 1997 Lexus ES 300
26 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: