Question about 1997 Chrysler Town & Country

Open Question

2004 knock sensor for town and country - 1997 Chrysler Town & Country

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
garyq1970
  • 85 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

Ad
short shadey
  • 421 Answers

SOURCE: location of the speed sensor on 1996 town & country

they are on the front drivers side of the transmisson and have two wires coming off them, there are two one is an input shaft sensor and the other is an output shaft sensor unless you have a 4 cyl van then there is only one sensor please rate -jeff

Posted on Sep 04, 2008

  • 17 Answers

SOURCE: I have a 2004 Chrysler Town and Country and my

P0440:

  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks

  • P0441:
    Bad vacuum switch
    • Broken or damaged EVAP line or canister
    • Open in PCM purge command circuit
    • Open or short in Voltage feed circuit to Purge Solenoid
    • Faulty purge solenoid
    • Restriction in EVAP solenoid, line or canister
    • Corrosion or resistance in purge connector
    • Bad PCM

    Posted on Dec 21, 2009

    • 1024 Answers

    SOURCE: 2003 town and country changed plugs and wires and

    did you replace the ignition coil? they do give you problem of skipping too.

    Posted on Mar 13, 2010

    jturcotte
    • 8560 Answers

    SOURCE: P0032 Oxygen sensor heater problem. This is on a

    The sensor in question is behind the engine on the exhaust manifold.

    You can test the heater in the sensor with an ohmmeter using the following procedure:

    1. Disconnect the electrical harness from the sensor.
    2. The white wires in the sensor connector are the power and ground circuits for the heater.
    3. Connect the ohmmeter test leads to the terminals of the white wires in the heated oxygen sensor connector.
    4. Check the resistance of the sensor, if it is not within 4-7 ohms, replace the sensor.
    5. ea87f67.gif

    Posted on Oct 24, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    2004 Chrysler Town and Country won't start. Lights, radio and horn works just fine. Even put in a new starter and still get nothing. Ran a wire from battery to the starter and got a little kick.


    Chrysler Town & Country Questions - My van won't start ...

    www.cargurus.com > Questions > Chrysler > Town & Country

    CarGurusSep 29, 2008 - ckf2004 answered 4 years ago. I have a 96 chrysler town and countrylx and the engine died, turned over but wouldn't start, I researched and replace the flywheel .... My van sometimes won't start because it kills the battery.

    My town & country 2004 wont start sometimes - CarGurus

    www.cargurus.com > Questions > Chrysler > Town & Country

    CarGurusMy town & country 2004 wont start sometimes - My van start doing something really weird. it will ... Asked by TownCountryguy May 03, 2013 at 03:31 PM about the 2004 Chrysler Town & Country Base .... Sometimes you tap it & it won't work.

    Van won't start - Chrysler town and country - YouTube

    ? 1:01
    https://www.youtube.com/watch?v=mkEL2vlLZr0
    Jun 26, 2014 - Uploaded by Philip Walker
    We have the same issue currently...very randomly...with our 2008 Caravan at the moment. Wife just got ...

    2011 Chrysler Town & Country Engine Won't Turn Over, Will ...

    www.carcomplaints.com/Chrysler/Town_Country/.../engine_wont_turn_...
    The 2011 Chrysler Town & Country has 34 complaints for engine won't turn over, will not start. Average repair cost is $902.00 at 58178 miles.

    Jan 14, 2016 | Chrysler Cars & Trucks

    1 Answer

    I changed thermostat, radiator, water pump, hose, engine cooling temperature sensor, radiator cap and I'm still overheating. 2004 Chrysler town and country


    Check the heater cores. There are usually 2 in a T&C. Also check the pipes running to the rear heater core. I recently had to have mine repaired because they were leaking!

    May 22, 2015 | 2004 Chrysler Town and Country

    1 Answer

    How do i replace ambian temp sensor on 2006 chrysler town and country 3.3


    front radiator support is where it's mounted just below hood latch

    Feb 20, 2014 | 2004 Chrysler Town & Country

    1 Answer

    2004 town and country evic doesn't display reset tire sensors


    You have probably found that if you drive for a few miles it will reset itself. If not there is a battery inside each unit in the tire and they go out. You can get a complete unit at the parts store for about 24 dollars and take it to Walmart and they will install it for 10 dollars2_25_2013_7_34_31_pm.jpg

    Feb 25, 2013 | 2004 Chrysler Town & Country

    1 Answer

    P0032 Oxygen sensor heater problem. This is on a 2004 Chrysler Town and Country 3.8 L V6.


    The sensor in question is behind the engine on the exhaust manifold.

    You can test the heater in the sensor with an ohmmeter using the following procedure:
    1. Disconnect the electrical harness from the sensor.
    2. The white wires in the sensor connector are the power and ground circuits for the heater.
    3. Connect the ohmmeter test leads to the terminals of the white wires in the heated oxygen sensor connector.
    4. Check the resistance of the sensor, if it is not within 4-7 ohms, replace the sensor.
    5. ea87f67.gif

    Oct 24, 2010 | 2004 Chrysler Town & Country

    1 Answer

    What does code p0032 mean in a 2004 chrysler town and country mini van


    Heater control circuit high, bank 1 sensor 1. Sounds like your O2 sensor in bank 1 in front of your convertor is bad.

    Sep 08, 2010 | 2004 Chrysler Town & Country

    2 Answers

    Knocking in the engine at startup and idle


    If the knocking is a very low hammering sound its the rear main bearing to the crack shaft gone bad

    Jan 16, 2010 | 2001 Chrysler Town & Country

    Not finding what you are looking for?
    1997 Chrysler Town & Country Logo

    Related Topics:

    22 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8560 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...