Passenger window off track 2001 ford expedition e.b.

Not off any track

You have a broken window regulator to replace

Try You Tube Video to see if they have door
panel removal

there should be screw behind mirror trim panel one bottom of door behind courtsey light and one behind trim panel for window controls then lift straight up on panel

SECTION 501-09: Rear View Mirrors 2003 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

Front Door Trim Panel —Expedition Removal and Installation
NOTE: Left front door shown, right front similar.

1. Remove the door handle bezel.
   • Use service notch.

1. Remove the window control switch plate.
   • Use service notch and disconnect the electrical connectors.

1. CAUTION: To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
   Remove the two bolts and three screws, and remove the door trim panel.

1. Remove the weather shield.

1. Disconnect the exterior mirror electrical connector.

1. Remove the exterior mirror.
   • Remove the nuts.

1. To install, reverse the removal procedure.
   • Install top nut first.

---
Exterior Mirror Motor Removal and Installation

1. Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.

1. Disconnect the heated mirror electrical connectors.

1. Remove the exterior mirror motor screws and exterior mirror motor.
   • Disconnect the electrical connectors.

1. To install, reverse the removal procedure.

Remove sail panel cover for mirror, remove screw. Remove window switch cover and remove screw. Remove courtesy lamp lens on door and remove screw. Remove inside door handle trim cover and remove 8mm bolt and handle. Lift upwards and remove door panel.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

remove the door panel with out breaking the hook style plastic clips by un doing any phillip screws holding the doors pull handle, and maybe a couple of lower retainer screws, remove the power window and power lock switchs from the doors handle than pull lightly on the bottom of the door panel . if it feels loose it should pull out about 2 inches.than slide the whole door panel straight up and off the door it self. now you can unclip the power mirror wire connector and remove the mirror itself from the upper corner of the door
good luck chris

There are 2 screws just above the door handle you need to remove. Remove the plastic trim around door handle. Then starting at bottom of door panel pull out to disengage the push pin clips and work your way up both sides of panel. Then lift up on door panel to disengage the weatherstip on top of panel.

You did not mention whether it was a front or rear door? I assume its a front because u stated no screws.

Here are instructions for front door:

Remove the plastic trim from behind mirror(just snaps on).
Remove the window switch panel(just snaps on).
Remove the screw behind the mirror cover.
Remove the screw behind the window switch panel.
Remove the courtesy lamp lens.
Remove the screw in the courtesy lamp housing.
Remove the inside door handle trim cover.
Remove the inside door handle bolt.
Lift upward and then outward to remove the front door trim panel

Both above answers are not right... I just replaced the Pass side power mirror assembly on my 97 Expedition. No heat, no directional.
The inside door panel must come off.
1. pry off interior triangular plastic trim piece inside of door at mirror area. Remove door panel screw at this area.
2. Pry off power window switch panel and remove door panel screw at this area.
3.Remove interior door light cover and remove screw at this area.
4. Remove plastic cover at door handle.
5. The interior door panel can now be lifted up to release it from it's fasteners.
6. Disconnect light and push power window switch assembly through the door panel and it can be set aside.
7. Disconnect mirror power at coupler.
8 Loosen three mirror mounting screws with 7/16 socket. DO NOT unscrew completely.. the will fall down the door cavity. Use a round magnet on holder to remove the screws completely.
9.Thread electrical connection into door panel and install mirror.
10. Smile when mirror works and drink a beer!
rayman

Hi,

Initially, try to determine which fuse goes to the power window. Check and replace if necessary.

In brief for a temporary remedy just to have the window closed: remove the triangular cover at the top front of the door behind the mirror, there should be a screw there; remove the trim around the door handle another screw, remove the cover of the courtesy light at the bottom of the door, there is another screw behind that; soon as all the screws are out, lift/push up on the door panel and pull off. This would grant you access to the mechanism controlling the window. You can try closing by manually turning the motor.

Thereafter, pls determine if it is the motor or the switch(es) has failed. Replacements are available here.

Incidentally, here is a nice tutorial on repairs of power windows in general.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.