Question about Renault Kangoo

Open Question

Removal ignition barrel - Kangoo Renault Cars & Trucks

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mcgyver468
  • 710 Answers

SOURCE: Removal of the ignition Barrek

HAVE YOU TRIED TO USE SOME SILICONE SPRAY ON THE NUT? MAYBE YOU CAN CUT THE NUT OFF WITH A DREMEL AND A VERY SMALL DIAMOND BIT WITHOUT CUTTING THE DASH. HOPE THIS HELPS. LET ME KNOW. GOOD LUCK

Posted on May 03, 2009

Ad
  • 135 Answers

SOURCE: I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING

it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

Posted on May 20, 2009

  • 4 Answers

SOURCE: mercedez 190 ignition barrel. I have taken out ignition barrel attached to steering coloum but i can not remove key ignition from steering coloum how does it remove ignition barrel from steering

Should be the same as w123 model. Check diy Mercedes web page.
Photos included easy to do.

Posted on Jul 07, 2009

e-Guru
  • 3917 Answers

SOURCE: how to remove jammed ignition barrell from 1992,

Hi

you can access the ignition switch from underneath the dash, but it is easier to remove the steering wheel, then the instrument cluster. There are two basic elements to the ignition switch. The part that usually breaks down first is the front section, where the key goes into. You have to remove the entire unit from its bracket. Unplug the wire loom from the back of the housing. I believe there are two screws holding both sections together. Remove the screws and replace the unit. Then re-assemble.

Please check the link bellow :-

http://www.ehow.com/how_5833556_remove-mercedes-ignition-switch.html


Please accept the solution if it’s helpful. Do get back to us for any further query.
Thanks for contacting fixya.com

Posted on Sep 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key broken in ignition barrel


Any parts store will have torx bits, this will remove the bolts.

Jan 12, 2014 | Ford Festiva Cars & Trucks

2 Answers

How do i take out my ignition barrel 98 vt


to remove you ignition barrel is a simple process you need to remover the steering column covers from around the ignition switch.
there is a small hole located in the ignition barrel you will need to gentle push and hold an Allen key in the hole and rotate the key to the accessories the barrel should be come lose and gentle be pulled out.
please note that if the internal locking mech is not correctly depressed you will not be able to remove the barrel.
also if you have lost you key you will not be ale to remove the ignition barrel and will need to get a lock smith to rplace the whole thing witch can cost from $120 up to $250 depending on the locksmith

Jan 02, 2013 | 1998 Holden VT Commodore

1 Answer

KEY STUCK IN THE IGNITION


just a guess on this one , some ignition barrels have a button underneath the key barrel , and to remove key you must push this in and turn key back one more klick away from start direction .

i am hoping that original key is in ignition , you can get ignition barrel replaced with new keys , but some steerng parts need dissasembling .
and some are pains to remove .
hope it was this simple !

Nov 10, 2010 | 2002 Isuzu Axiom

1 Answer

I have an Isuzu Rodeo and the key is stuck in the ignition any idea how to get it out? Year 2000


replace the whole ignition barrel with new key and get key programmed by dealer
can remove barrel and key by removing steering column covers turn ignition to on position and with small shank screw driver push in hole in outer top rear section of barrel assembly then pull out ignition lock barrel with key in it. fit new lock barrel and key, program new key into system and can get door lock barrels coded to suit new key or get code for old key and cut new key so it fits mechanical locks on the rest of the vehicle (just wont turn in ignition) 2 keys for vehicle.

Jun 13, 2010 | 2000 Isuzu Rodeo

2 Answers

Key broken off in ignition barrel - how do I remove the barrel?


not saying it is landrover barrel but best way is get your new barrel and that should tell you how it is fitted normally a spring loaded pin holds barrel in socket

Mar 20, 2010 | 1994 Land Rover Discovery

1 Answer

How to remove ignition barrel from 1997 toyota celica


Remove the plastic covers around the ignition switch, insert the key in the ignition and turn the key to ignition on position (just before start position) now locate the pin on the side of the ignition switch which is flush with the aluminium housing holding the barrel,the pin is about 3 mm in diameter.Gently press the pin inwards (which is spring loaded) with a sharp pointed object e.g small screwdriver and at the same time while holding the pin, pull on the ignition key as if you want to remove the key, and the barrel will slide out completely.

Regards
Phillip

Sep 17, 2009 | 1998 Toyota Celica

1 Answer

I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING IN IGNITION BARREL NOW THE STEERING IS LOCKED ALSO I HAVE TAKEN OUT IGNITION BARREL WITH STEERING COLOUM. i WOULD LIKE TO DISINGAGE THE IGNITION BARREL...


it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

May 19, 2009 | 1993 Mercedes-Benz 190

2 Answers

Removal of the ignition Barrek


HAVE YOU TRIED TO USE SOME SILICONE SPRAY ON THE NUT? MAYBE YOU CAN CUT THE NUT OFF WITH A DREMEL AND A VERY SMALL DIAMOND BIT WITHOUT CUTTING THE DASH. HOPE THIS HELPS. LET ME KNOW. GOOD LUCK

May 03, 2009 | 2005 Chevrolet Corvette

1 Answer

Key's snapped off inside ignition


Hi I would suggest you ring the Automobile association, and see whether one of their mobile mechanics can solve your problem. extracting a car key from the barrel may be more difficult than it appears. He, the mobile man may have done it before and have the right tools for the problem.

May 30, 2017 | 1995 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

xxxxxx xxx

Level 3 Expert

4862 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...