Question about Nissan Almera

Open Question

Where is the crank shaft sensor 1.5 almera - Almera Nissan Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jschoon77
  • 55 Answers

SOURCE: crank shaft sensor

I have 10 years experience in a Nissan dealership and I know without a shadow of a doubt that the Crankshaft Position Sensor is NOT located next tp the crank pulley... it is rather at the other end of the engine near where the transmission bellhousing bolts to the engine block. It is on the side toward the firewall near the bottom. Even if you can get the vehicle on a lift and get under it, you can't really see it... It's more of a feel thing... There was a campaign (recall) on these engines to replace Crank Position and also Cam Postion sensors. Check with your dealer- the campaign might be open. You will need your VIN number when you call.

Posted on Oct 29, 2008

Ad
  • 1 Answer

SOURCE: 2005 Subaru Baja Crank Shaft Position Sensor

is there a problem using e10 ethonal in a subaru impreza wrx 2003

Posted on Nov 24, 2008

66 chrgr
  • 1011 Answers

SOURCE: crank shaft sensor. where is it located on a

behind the engine on the top passenger side of the engine. 2 13mm. bolts.goes through the bell housing.

Posted on Mar 29, 2009

  • 383 Answers

SOURCE: CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA

1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Posted on Apr 06, 2009

wracefans24
  • 1985 Answers

SOURCE: crank shaft sensor? is this the same as cam shaft

no each one has its own job,
crank sensor is counting crank shaft rpms
cam sensor is counting cam shaft rpms
is there any lights coming on just as this is happening?
i think you should have the fuel pressure checked when it dies out,you need at least 50psi at fuel rail

Posted on Dec 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Nissan Almera keeps cutting out completely whilst driving?


run the fault codes and look for cam/crank position sensors.
faulty or loose connections may cause this fault. If you have more than 1 key in the ignition then it has been known that the mass of swinging keys will switch off the ignition
(current recall on all GMC ignition switches for just this reason)

Feb 13, 2015 | 2005 Nissan Almera 1.6

1 Answer

My speedo has stopped working i had the speed sensor replaced it worked for just 1/2 mile n stopped, local garage said new gearbox does this sound right to u guys


If they mean the speedo gearbox, maybe. I think this works like older cars in which you have a gear on the transmission shaft which drives a gear on the speed sensor, and sometimes the gear on the transmission shaft can break the clip which locates it and it slips out of position. Many transmissions allow removal of back section to gain access to repair this. However, some newer cars have a speed sensor which uses an electromagnet to pick up signal from a internal magnet. Removing the speed sensor from the transmission (easy!) should help determine the cause of your problem.

Dec 15, 2014 | 2005 Nissan Almera 1.6

1 Answer

Nissan Almera wont start with code P0345


Code 345 means the cam sensor on bank two is not sending the correct signal to the engine computer. So no spark.
If you have replaced the sensor, the problem could be the cam or the wiring from the sensor to the computer.

Dec 03, 2014 | 2005 Nissan Almera 1.5

1 Answer

My almera 1.6 2004 model coils not recieving power.


ok, i will try and help you as much as i can. first you should be getting 12 volts a pulse and a ground( negative ). if you're getting the 12 volts and the grounds but no pulse the the car has 2 sensors, one is the cam and the other is the crank. those sensors provide pulse to one for the injectors and the crank is for the coil packs. you can test for pulse by using a noid light or the normal test light. just connect the test light to 12 volts terminal and have someone crank over the engine. if you don't get a low flickering light then you neeed to change the sensor

Oct 17, 2014 | Nissan Almera Cars & Trucks

1 Answer

Nissan almera se


The computer is not getting the right signal from the crank sensor.
The sensor tells the computer which cylinder is at top dead center for ignition and the fuel injectors.
The sensor and circuit would need to be checked.

Jul 22, 2013 | Cars & Trucks

2 Answers

I have two codes showing on my 2005 Nissan Altima. The first is the Engine speed sensor CKT malfunction and the second is Crank shaft position sensor A circut malfunction. what does this mean?


Hi got a Nissan almera 2002 1.5 it won't start it try's to but cuts off it brings code air mass flow I have changed that but still wnt start

Jan 25, 2011 | 2005 Nissan Altima

1 Answer

I have an 05 petrol Almera. The engine light came on and the fault was diagnosed by main dealer as either a crank shaft sensor or the timing chain. The car has been loosing power sporadically and is...


the cheapest route for you to start with, and most likely the problem is a bad or faulty crank position sensor, it works hand in hand with the coil to tell the vehicle when to fire.. so it would make it hard to start, and run crappy. hope this helps

Dec 07, 2010 | Nissan Altima Cars & Trucks

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...