Question about 1998 Toyota Camry

Open Question

Where is security alarm toggle switch 96 camry

Can i disconnect horns and try the 30 min over-ride process for deactivating alarm.Then start with key .

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: alarm goes off when new battery in placed in car,

Hello. If you have a FACTORY alarm system, the deactivte prodedure is to cycle the key off-on (not to start) 5 times, in the ignition. This feature is provided in case you lose the remote, or the remote battery goes dead.

Note: this will only work with the Factory system. If you have an aftermarket system, this answer will no benefit you.

Posted on Dec 12, 2009

  • 1 Answer

SOURCE: HOW TO DISARM FACTORY ALARM SYSTEM

I had a similar problem with my '94. Try disconnecting the battery, wait 30 seconds and reconnect the battery. This should reset the alarm.

Posted on Aug 25, 2008

  • 104 Answers

SOURCE: My 96 toyota camry can't be started because the

Find the alarm box (module) under the driver's side dashboard;right around feet area. You may need to remove a few panels. Find the box and disconnect the connector, then try to start it. I believe it's not cranking? Let me know anything else.

Posted on Jun 12, 2009

  • 1 Answer

SOURCE: 2001 toyota rav4. how do you deactivate the alarm

Followed your recommendation of holding the valet (red) button for 6 seconds. It deactivated the alarm system and I was able to start the vehicle. This solution saved me from buying another key from the dealership (139$) and a programming charge of (100$). And not to mention the time saved from towing the vehicle to the dealership. I can't thank you enough for time and money saved with this valuable service. Will be signing up with your service when I get back from Orlando.

Posted on Aug 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How to set & cancel theft deterrent system or how to set & cancel security...


Theft deterrent system (on some models)

Theft deterrent system is designed to deter vehicle theft. The system flashes the turn signal lights and turns on the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn when it detects abnormalities such as follows:

• Any door or hood is forcibly opened.
• The batter terminal is disconnected and then reconnected
• The system control is disconnected and then reconnected.
• Abnormal impact is detected when the impact sensor function is on.

The system flashes the turn signal lights and turns the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn if someone attempts to damage or break into your car.

Setting the system

You can set the system with or without the impact sensor function. For details, see "Canceling the impact sensor" below.

1. Turn the ignition key to "LOCK" and remove it.
2. Have all passengers get out of the vehicle
3. Push the lock (set) switch on the wireless remote control key once. At this time, the turn signal lights flashes once and the security indicator light comes on.

The system is set after 30 seconds. At this time, the security indicator light start flashing slowly.

Once the system is set, you cannot start the engine until you cancel the system.

The system will not be set in the following cases.

• When any of the door is open; security horn sounds for 1 second, close the door and set the system again.
• When the hood is open; close the hood securely.

Canceling the Impact Sensor

The impact sensor can be cancelled to prevent false alarms from being triggered incase of the following conditions:

• When parked in the noisy area
• The vehicle body or glass is subjected to a strong impact from the (such as in highly pressurized car wash).
• When transporting by a car carrier or ferry.

To cancel the impact sensor;

1. Lock the door by pushing the lock (set) switch on the wireless remote control key once, and turn signal light flash once
2. Then push the lock (set) switch twice within 5 seconds. At this time, the turn signal flash 5 times to indicate the impact sensor function is disable.

The impact sensor is deactivated as long as the system remained armed.

Canceling the system

The system will be cancelled by the following two ways:

• Turn the ignition key from "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch

If the turn signal lights flash 3 times, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

If any of the doors is not opened within 30 seconds, all doors will be automatically locked and the system will be set.

When the system is set

Activating the system; When the system detects abnormalities such as follows, it flashes the turn signal lights and turns on the interior light or the turn lights only (depending on the model) and sounds the security horn and vehicle horn of 30 seconds.

• Unlocking any door without using wireless control
• Any door or hood is forcibly opened.
• The battery terminal is disconnected and then reconnected.
• The system control assembly is disconnected and then reconnected
• Abnormal impact is detected when the impact sensor function is on.

Reactivating the alarm;

Once set, the system automatically resets the alarm after the alarm stops.

The alarm will activate again under the same circumstances described in "Activating the system".

Stopping the Alarm

The alarm will be stopped by the following two ways;

• Turn the ignition key from the "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch.

The system can be cancelled by these ways at the same time.

If the battery becomes discharged due to the vehicle being unused, for a long time etc., when the battery is recharged or replaced, the system will activate the alarm. If this happens, immediately unlock any of the doors by pushing the unlock (cancel) switch, and the alarm will stop.

Testing the system

1. Set the system
2. Insert a wireless remote control key into the key hole on the driver's door handle, and unlock the door.
3. Open the door, and an alarm will sound.
4. Stop the alarm by pushing the unlock (cancel) switch.
5. Repeat this operation for the front passenger's door.

Good luck.

on Nov 08, 2010 | Toyota Pickup Cars & Trucks

1 Answer

2002 mercury villager anti theft system horn will not stop van will not start


The remote needs to work if the vehicle originally came with the remote from the factory. It gives off a signal to the ring around the ignition switch to deactivate the alarm.

Jan 09, 2014 | 1998 Mercury Mystique

2 Answers

Alarm goes off


Immobilizer seems to be active, same with your alarm. May be faulty, need to replace.

Jan 04, 2014 | 1996 Toyota Camry

1 Answer

1994 toyata camry the alarm goes off and will not let me start the car.


factory security does not have toggle switches as far as I know so it is probably an aftermarket system. Try one of two things, turn the toggle switch the oposite direction with battery disconnected. Reconnect the battery and try again, the horn will beep a few times when you reconnect. try starting. If that doesn't work, disconnect the battery and turn the key to the on position and reconnect the battery and the horn will sound but will go off get in the car and try to start. It should start and run normally. shut car off, then you should be able to return the toggle switch to the previous position If this happens again turn the toggle switch to the opposite position with the batterry disconnected and turn the key switch to the on position and reconnect the battery and start when started go see a service that installs aftermarket systems and they should be able to reset it security system Hope this helps

Sep 19, 2012 | 1994 Toyota Camry

2 Answers

Well I'm looking for possible soultuions before I try it . I recently had to put a battery in my 2002 toyota rav4 and my alarm goes off everytime I open the door ...... goes off for 30 secs or so ...


Sorry you can't disconnect it. you should be able to reprogram it though. look in your owners manual. most are programmed threw the radio controls.

Aug 07, 2011 | 2002 Toyota RAV4

1 Answer

My car wont start and the alarm keeps goin off when i open the door. Can you help me please. for a 1994 toyota Camry


Try disconnecting the battery and putting the key in the ignition and turning it to the "ON" position. Reconnect the battery and the alarm should be deactivated. I'm assuming you don't have the alarm fob? This might be a good time to remove the alarm system.

Feb 07, 2010 | 1994 Toyota Camry

1 Answer

I replaced battery in my audi 80 2.0 tdi but have lost the remote and alarm wont stop going off .


Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction: Alarm LED in rear fog lamp switch illuminates for 30 seconds when vehicle is locked.
How
NOTE: A maximum of 4 keys can be programmed (one at a time).
As memory positions of existing keys are unlikely to be known: Obtain and reprogram all keys.
NOTE: Existing key memory positions will be overwritten.
Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Using first key, press unlock button once (programs memory position 1). Alarm horn sounds once to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF. To program remaining keys into memory positions 2, 3 and 4. Carry out the complete procedure below for each key: Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Press unlock button at 1 second intervals, as follows: Twice for memory position 2 (second key). Three times for memory position 3 (third key). Four times for memory position 4 (fourth key). Alarm horn sounds once every time unlock button is pressed, to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF.
NOTE: Ignition MUST be switched OFF between each key programming procedure

Jan 10, 2010 | 1992 Audi 80

1 Answer

HOW TO DISARM FACTORY ALARM SYSTEM


I had a similar problem with my '94. Try disconnecting the battery, wait 30 seconds and reconnect the battery. This should reset the alarm.

Aug 06, 2008 | 1995 Toyota 4Runner

Not finding what you are looking for?
1998 Toyota Camry Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...