Question about Cars & Trucks
Need to take it to a shop that can do a TPMS reset. I know all Firestone shops can do this for you.
Posted on Dec 12, 2012
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
I have a 2004 Silverado with the same problem.
After scrollng the internet for months and reading every manual I could get my hands on, I found, for me, a quick and easy way. Open the hood, remove the cover to the Underhood Fuse Block on the drivers side of the vehicle near the battery.
If you have the manual for your truck, go to page 5-126 and locate the fuse that says IPC/DIC, it is a 10 amp fuse.
Pull the fuse and start your truck or a few sceonds.
You will notice that nothing on your insterment will work.
Turn engine off and replace fuse.
After I did this, the message did not come back, and started my truck about 15 times to make sure.
It worked for me....good luck to you.
Posted on Feb 14, 2009
1. Remove the fuse panel cover, located on the right hand side of the dash (you have to open the front right hand passenger door). It comes off easily, it is held in place by three spring clips. Be careful when pulling this off, that you don't disengage the spring clips from the panel door, because they will fly off into the dash, and you won't be able to get them out. Replacement clips are about 70 cents each at the Buick dealer, but they will only sell them in a bag of 20, so do the math. Lose the clips, it will cost you about $16 with tax to replace them. I know because I did this :(
2. Start your car, and with the engine idling, locate the RESET button on the fuse panel where you've removed the fuse panel cover. It's a red button, the first one on the top row of the fuse block. Press and hold the RESET button for five seconds. The "low tire" light should come on and flash three times, then go out. If it doesn't, you'll have to take your car to the dealer or other repair shop for service.
3. Replace the fuse panel cover, and you're good to go! BTW, this information is on pages 6-42 and 6-43 of your Owner's Manual. :)
Hope this helps and good luck!
-KC GTO Dad
Posted on Sep 18, 2009
Testimonial: "thanks this is what i needed to know"
if the tires have been rotated it could be a diff tire and sometimes its actually the spare, put 2 lbs over the recommended amount on the inside of the driver side door in all 5 tires if that dont work a dealer will have to see which sensor is bad
Posted on Nov 11, 2009
After you have changed a tire and adjusted your tire pressures you will need to initial the tire pressure monitoring. If your vehicle does not have I-drive then with the iginition in the on position on the left steering wheel stalk, move the rocker switch up and cycle through until you see an icon in the cluster that says initailize. push the button on the end of the stalk inwards toward the steering wheel and hold until you see the icon in the cluster show a check mark. When it shows a check mark your finished.
Posted on Jun 03, 2010
Tips for a great answer:
Feb 06, 2015 | Cars & Trucks
Aug 19, 2013 | 2004 Ford Freestar
Jan 09, 2013 | Cars & Trucks
Oct 04, 2012 | 2004 Cadillac Deville
Mar 04, 2011 | Chevrolet Impala Cars & Trucks
Apr 20, 2010 | 2004 Ford Freestar
Dec 05, 2009 | 2006 Lexus Ls 430
Apr 13, 2009 | 2003 Hummer H2
Apr 03, 2009 | 2004 Isuzu Rodeo
60 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: