Question about 1997 Audi A6
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: electric window
STOP! Don't spend hundreds of $$ or ££ on an entire new regulator mechanism. It's probably not necessary.
There's a weak part in the design. It's the bit which links the steel cable to the window. They are plastic and they tend to break, leaving one side of the window unsupported (or at least un-driven).
Audi have redesigned the part, making it stronger (now with a metal reinforcement). In the UK, the cost of the part is about £1.60 ($2.60). You can even replace the part WITHOUT removing the regulator mechanism. The part number is 4B0-837-463-B. (Don't miss the -B).
I thank the good people at http://forums.audiworld.com/a6/msgs/307886.phtml for the help.
Also: http://www.audiworld.com/tech/int45.shtml (This describes another method, which involves taking the mechanism off).
My own tip: If you're doing it without removing the works, get the new part and run the screw into the fixing hole to form a thread BEFORE you try to do it on the car.
Disclaimer: This worked on my '99 A6. No responsibilty if you should break your window, trap your fingers, drop a screwdriver on your toes etc.
Posted on Oct 22, 2008
No Manual BUT I can tell you that All Door Pannels are attached By A Combo of SNAP Fasteners And Hidden Screws, Most Parts Stores Have the Tool Cor Pannel Removal"SNAPS" And If you LOOK VeryHard the Screws Can Be Found Some are Covered By Small Plastic Covers Witch a Flathead Screwdriver will Remove.
I Hope this Helps You
Posted on Jun 01, 2009
SOURCE: AUDI A6 WINDOW PROBLEMS
This is a common problem with the C5 A6 models. Before you replace the fuse for the windows (I think it's number 14, but i don't have a manual in front of me - Anyway, it's the 10A fuse that's blown!) Look under the back of both front seats and you'll see a light that illuminates the floor for the back seats. Rem ove the light from each seat by prying it out with a flat screwdriver and disconnect both leads. Replace the fuse, and your windows (moon roof and interior lights as well) should now work. The lumbar support causes something to short out the lights. I've tried insulating the lights on mine, but the problem always comes back so I just disconnected them altogether.
Posted on Jun 15, 2009
This info is wrong, remove the screws at the top of the panel along the edge ( one on the hinge edge and one on the latch edge. Remove the cover from the interior door handle by locating the hole on the bottom edge of the handle, insert a punch to release the cover, once the cover is released remove the 2 screws holding the handle on. Remove the handle.Once the handle is removed take the black trim piece that the handle seats into off. Pull the interior latch handle forward enough the remove the cable. Remove the latch handle. There is a small hole in the vynal under the latch handle, the last remaining screw that holds the panel on is inside this hole, remove it. The hole is hard to see, this took me several hours to find not knowing it was there. Remove the window switch module by sliding a screwdriver under the edge that faces the latch end of the door, push in the metal clip and pry up on the switch assembly. there are 2 plastic tabs that hook into the arm rest on the hinge end, that is why you must pry up from the latch end. Disconnect the plugs from the switch. Now you are ready to remove the panel. grasp the panel through the hole for the latch handle and pull up about 1" the panel should com free from the door. Do not pry the panel out from the door or you will break the plastic tabs that hold the panel on. Once you lift the panel up and off the door you will need to disconnect 2 electrical connectors and remove the white foam plug that seals the window switch harness into the arm rest and remove the window control wires from the panel.
Posted on Mar 23, 2010
Tips for a great answer:
Mar 23, 2015 | 2003 Audi A6
Sep 11, 2010 | 2006 Audi A6
Sep 01, 2010 | 2001 Audi A6
Aug 03, 2009 | 1999 Audi A6
May 29, 2009 | 2001 Audi A6
Jun 22, 2008 | 2001 Audi A6
126 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: