Question about 1995 Chevrolet Blazer

1 Answer

I need a vacuum line diagram for 1995 blazer 4.3

All vacuum lines are gone & I need to relace them

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,333 Answers

Click here to see vacuum diagrams.

Posted on Dec 12, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wracefans24
  • 1985 Answers

SOURCE: 1989 Chevy S10 Blazer, 4.3L V6. 4wd not working.

under the battery is where you need to check first,then follow it down around the right front wheel well,

Posted on Dec 09, 2009

ZJLimited
  • 17970 Answers

SOURCE: i need a vacuum diagram for a 99 blazer 4.3

Check this (click for zoom)...

73219f5.jpg

Hope this help (remember comment and rates this).


Posted on Jul 22, 2010

kapishtech
  • 2272 Answers

SOURCE: Looking for the diagram of vacuum hoses and lines

Diagram for vacuum hose and lines is shown below.Check fig:--
0fe5c17.gif
thanks.

Posted on Jun 10, 2010

cgtotty
  • 1 Answer

SOURCE: chevy s10 broken vacuum line

The plastic line in the wiring harness goes to the heater controls; and believe it or not , the other end goes to the vacuum tank - but its in the FENDER !!!!! behind the ABS, kinda under the drivers side hood hinge - great place to put one ain't it ? No wonder GM is going broke !! Good Luck

Posted on Dec 25, 2008

  • 2002 Answers

SOURCE: Need vacuum diagram

I can't send you a diagram but I can tell you the basics that should get you mobile. Take a vacuum line from the lower front of your carb and hook it to your distributer vacuum advance. Take another from the front of your carb and run it to your EGR valve. It should be beside the carb on the intake manifold. At the rear of your carburator there is a large line coming out. It should be steel. It provides vacuum boost to your power brakes. Hook it up. Make sure all other vacuum outlets on the carb and intake are blocked off and you should be able to get mobile.

Posted on Jun 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced the leaking vacuum line and four ignition coils and it seemed to help some. The Tahoe will suddenly start the rough idling and I was able to check the fuel pressure and it was 60psi.


fuel pressure at 60psi means the fuel system is good
could be problem injectors ( blocking up or wiring problems ) so have them serviced

Dec 14, 2016 | Cars & Trucks

1 Answer

I have a 1995 Chevy S10 Blazer and have dropped 3rd gear in the transmission. 3rd gear seems like it is in neutral and from time to time you can hear a rattling noise that seems to be coming from the...


Vacuum Reservoir-- I think that is your Evap
Canister,nothing to do with the trans

Pull the trans & rebuild it ,it is done,worn out

No vacuum hose on that trans-- is there

Not been under there to look

Nov 02, 2014 | Cars & Trucks

1 Answer

2004 landrover freelander, engine light came on, engine surging


Check throttle positioning sensor, replace if needed,

Check Vacuum lines for tears or wear, replace if needed.

Check for intake gasket leaks, relace as needed.

Jan 21, 2013 | 2004 Land Rover FreeLander

2 Answers

Idle speed is to fast


They probably had your air filter out, 1st check the intake tube & vacume lines on the air cleaner box & intake tube. Make sure the clamps are tight & all vacume lines are on

Oct 15, 2012 | Daihatsu Sirion Cars & Trucks

1 Answer

It jerks when accelerating


EGR Valve is a possible,maybe

If it has vacuum lines disconnect,plug
& road test. If problem goes away
you replace the egr

There may be other vacuum valve or devices
in the egr system,so best to look at diagram
if under the hood to try & get one.

All I'm suggesting is separating vacuum issues to
the symptom.

Any vacuum leak anywhere will need to be fixed.

You need to know if the ignition is a problem
That does not mean start throwing parts at it.
Those days of a tune-up are long gone some
25 years ago

Every driveability issue has to be diagnosed

Sep 11, 2012 | 1994 Lexus LS 400

1 Answer

A mechanic pull all my vacuum lines on my 95 dodge


Take it back to the mechanic and have finish the job he started.

Feb 23, 2010 | 1995 Dodge Caravan

1 Answer

Heater and a/c controls on my 1996 Dodge Ram Van 3500


There's a large black ball or bullet shaped black plastic cylinder called a vacuum collector under the hood. Check to make sure this is leak proof. to do so just run the motor/engine for a few minutes and pull one of the vacuum lines off from it. yuo should get a long hissing sound. If not relace the two vacuum lines. If you do hear the sound then....it gets a little tricky. BEHIND the climate control unit is a vacuum harness with several different colored lines all held together at the connection end. If you can get at this, pull radio, pull ashtray assy, you may find that it has slipped off the control unit. Check these steps in the order that I've given, it will save you alot of headaches. It might boil down to needing a new/ used climate con trol center. Thanks and good luck, Dana

Aug 25, 2009 | 1999 Dodge Ram

1 Answer

Relaced battery now vents don't work


There is a flap in the venting that can stick. This vent is contolled by a vacuum operated actuator that may be leaking. This actuator has a vacuum hose that runs to the contol panel. Check the vaccum lines hear as well.

Aug 25, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Hard brake pedal on cadillac


Check the vacuum line that goes to the brake booster which is on the firewall behind the master cylinder. Good luck. Let me know if this helps please.

Apr 28, 2009 | Cadillac DeVille Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

2,995 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...