Question about 1993 Dodge Caravan

1 Answer

Starts and idles but wont go in to gear

Could it be a cv joint as it will not go in to drive or reverse

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,101 Answers

Check the transmission fluid first. if the axle was broken you would hear loud banging this is the link to my garage I am on facebook.https://www.facebook.com/TedsRepairs

Posted on Dec 12, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 holden cruze has started to make a clicking noise when in low gear. I don't seem to hear it in higher gears and it it doesn't make it in reverse..


the clicking noise especially on slow turns indicates that the cv joints need replacing
have it checked out by an accredited transmission or drive line shop

Oct 13, 2015 | Holden Cars & Trucks

5 Answers

Does the 1988 Nissan Stanza have U-joints? The reason I ask is because when the car shifts it jolts. And when you put it in gear it jolts and vibrates. I looked under the car and I dont see a driveline. Is...


Hi, yes you have front wheel drive. The drive shafts are on each side going from the transaxle to the wheels. each axle has 2 constant velocity (CV) joints. This is a bit different than a U-joint but serves the same purpose. There are 2 indications of a worn out CV joint. Id the boot is torn, the CV will wear out due to dirt getting in. If you hear a popping noise when making a sharp turn, that is a worn our CV joint. If your boots are intact and there is no popping on turns, the odds are the problem is not with the joints but somewhere else in the drive train. Raise the car and turn the wheels by hand to see where the play is coming from. let us know if you have more questions, and thanks for using FixYa.

front wheel drive axle:

jturcotte_170.jpg

Jan 20, 2011 | 1988 Nissan Stanza

1 Answer

How do u get the drive axle thats broke into two ?


I'm not sure of your question but I think you want to know how do you replace to drive axle also known as the CV joint. To replace the CV joint jack up the side that broke and remove the wheel. Then remove the center nut that holds the CV joint to the hub. Put the car in gear or park so the hub will not turn why you do this or have someone put on the brake why you're doing this. Then remove the lower ball joint. Now pull the hub outward as you push the CV joint in. You may have to do some prying. Now using a pry bar snapped the other side of the CV joint out of the transmission. Reverse this to install new one. Good luck.

Jul 15, 2010 | 1994 Ford Tempo

1 Answer

I have an automatic gas 2006 hyundai tucson. recently i noticed that when i engage the drive or reverse gear the vehicle lurches forward or backward accompanied by a banging noise. i have had both engine...


idle air control valve or iac same thing it controls idle speed yours is to high or you have a bad cv joint but i dnt think its that to new of car i would say your idle is to high

Apr 04, 2010 | 2006 Hyundai Tucson

1 Answer

Starts, but wont move


Sounds like a broken axle (CV joint) or your transmission has gone

May 01, 2009 | Mitsubishi Mirage Cars & Trucks

1 Answer

Problem with reversing on full lock on renault espace


it sounds more like the drive shaft is loose.that would be the jumping you feel. a cv joint clicks etc but it wont thump like that you might have the drive axle looked at

Feb 01, 2009 | 2002 Renault Sportwagon

2 Answers

CV cplaced still clicking


seeing as it is a 4wd and you replaced all the problem areas( this wont cost you anything but 75W90 x 2 Quarts and RTV) take all but the top diff cover bolt out of the front of your jeep let all the fluid drain then take off the top, sift thru your gear oil that came out with a magnet and see what you collect. if not much visually inspect your carrier and spider gears and your gear and pinion. I can almost gaurantee your problem will be in either the spiders or your gear

Jan 03, 2009 | 1998 Jeep Cherokee

Not finding what you are looking for?
1993 Dodge Caravan Logo

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...