Question about 2007 GMC Yukon

Open Question

2007 YUKON 5.3 OIL PRESSURE SWITCH LOCATION - 2007 GMC Yukon

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: 2007 yukon when should I CHANGE THE OIL HOW MANY

You can go down to 1%, but if you want the motor to last, you need to change it every 5K.

Posted on Jul 28, 2009

Ad
  • 127 Answers

SOURCE: 1995 GMC YUKON I HAVE A QUSTION THERE AN OIL

the pressure switch is loctated on top of the oil filter housing, should be a round metal cylinder style with oen wire going to it, left side of motor right next to tranny

Posted on Nov 13, 2009

Testimonial: "good advice "

BCAS1298
  • 3092 Answers

SOURCE: oil pressure sending unit location on 97 gmc yukon

Oil pressure switch, back of engine on top below ignition distributor.

Posted on Nov 11, 2010

  • 836 Answers

SOURCE: I HAVE A 2007 GMC YUKON XL WITH A PEGGED OUT OIL

on the top rear of the block.

Posted on Jan 22, 2011

ddc3
  • 144 Answers

SOURCE: 2004 gmc yukon lite came on low oil pressure just

There can be alot of causes, such as valve covers leaking, oil pan gasket leaking, oil filter leaking, rear main seal leaking, front timing chain cover seal or gasket leaking even bad rings. Does it smoke out of the back? Your valve seals could be leaking. Best way to find out if you have a leak is to inspect the valve covers manually, or take newspapers and lay them under the entire engine on the ground, and it will leave the tell tale stain of a leak. Hope this helps.

Posted on Jun 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pressure switch


Sender can most easily be changed by using special socket made for this purpose.

Mar 08, 2014 | 2007 GMC Yukon XL Denali

1 Answer

2005 GMC Yukon oil pressure extremely high.


You may have to pull the oil pressure regulator to clean out the relief valve / plunger. Some times it is accessible from the side of the block and with others the pan has to come off as it is a part of the oil pump.

Jan 25, 2014 | Cars & Trucks

1 Answer

CHANGED MY OIL BECAUSE GAGE WAS READING LOW OIL PRESSURE AND I HAD NO OIL LIFE, TRIED TO RESET OIL LIFE TO 100%, WHICH I DID BUT ON MY DASH ITS STILL READING LOW OIL PRESSURE AND THE GAGE GOES BACK AND...


you either have a faulty oil pressure switch or you have poor oil pressure.if you find the oil pressure switch remove it and install a manuel oil pressure guage there. then you will see if it is the actual oil pressure weak or if it is the switch.

Jan 09, 2011 | 2003 GMC Yukon XL

1 Answer

Oil pressure sending unit location on 97 gmc yukon where is it


Oil pressure switch, back of engine on top below ignition distributor.

Nov 11, 2010 | 1997 GMC Yukon

1 Answer

Oil pressure sending unit on 97 gmc yukon location


Oil pressure switch. back of engine on top below ignition distributor.

Nov 11, 2010 | 1997 Chevrolet Suburban

2 Answers

Hello, I have a 2007 GMC Yukon with around 47K miles.All service has been done at a GMC dealer on schedule and a oil change was done about 1500 miles ago. My question is that this week the oil low/check...


Probably just the oil sending unit internally defective.Just have them install a pressure tester and make sure the pressure is good.I`m sure this will be the sending unit.Hope this helps.Good luck.

Jan 23, 2010 | 2007 GMC Yukon

1 Answer

1995 GMC YUKON I HAVE A QUSTION THERE AN OIL SENDING SWITH AND A PERSURE SWITCH FOR THE 1995 GMC YUKON 2 DR 5.7 V 8 I AM HAVING TROUBLE WITH THE OIL GAUGE AND IT GIVING FALSE READING THERE A SWITCH ON THE...


the pressure switch is loctated on top of the oil filter housing, should be a round metal cylinder style with oen wire going to it, left side of motor right next to tranny

Nov 13, 2009 | 1995 GMC Yukon

Not finding what you are looking for?
2007 GMC Yukon Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...