Question about Suzuki Cars & Trucks

Open Question

Suzuki carry pickup lower ball joint - Suzuki Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: lower ball joint removal how to

  1. Remove the steering knuckle with wheel hub and bearing attached.
  2. Remove the lower ball joint flange with a chisel.
  3. Install J9519-E and J34874 to the lower ball joint.
  4. Remove the lower ball joint from the lower control arm using J9519-E and J34874


  1. Install the lower ball joint and J9519-E, J41435, and J45105-2 to the lower control arm.
  2. Install the lower ball joint to the lower control arm using J9519-E, J41435, and J45105-2.
  3. Remove J9519-E, J41435, and J45105-2 from the lower control arm
    1. Install J9519-E and J45105-1 to the lower ball joint.
    2. Flare the lower ball joint flange using J9519-E and J45105-1.
    3. Remove J9519-E and J45105-1 from the lower ball joint.
    4. Install the steering knuckle with wheel hub and bearing attached. Install the tire and wheel.
    1. Lower the vehicle.
    2. Check the front wheel alignment.
these jouints are pressed in and there is a flange that is flared this is what the tool numbers refer too.

Posted on Sep 12, 2008

chrischronic
  • 235 Answers

SOURCE: lower ball joint broke on a 95' lincoln towncar

it must be pressed out with a ball joint press then new one pressed back in. this job is for a machanic

Posted on Apr 15, 2009

chrisK1997
  • 103 Answers

SOURCE: 2000 lincoln ls bad ball joints! should i replace whole knuckle or just ball joints

yes you can buy just the ball joints

Posted on Apr 18, 2009

  • 314 Answers

SOURCE: Lower Ball Joint

You will have to remove it and replace it with a new one. The general steps for doing that is: 1)remove the tire 2)remove the caliper and rotor 3)remove the outer tie rod from the spindle 4)remove the axle nut 5) remove the cv axle 5)remove the nut on the ball joint 6) bang ball joint out and press in a new one. Then reassembly is exactly the reverse as disassembly.

Posted on Jun 10, 2009

  • 2002 Answers

SOURCE: upper and lower ball joints

Jack the truck clear of the ground and let the wheel assembly hang. After you remove the tire place your jack under the lower control arm so it's firm. Remove the cotter pin, if you have one and loosen the big nut almost off. Wedge a "pickle fork" between the control arm and the spindle and give it a belt with a hammer until the ball joint pops. Raise the jack so you can undo the nut easily and separate the control arm and spindle.
The upper ball joint is riveted or bolted in. Grind the rivets or use a cold chisel and remove the ball joint. Clean up the area with some sandpaper, dirt , loose rust, etc.and put the new joint in. Put the spindle back on using the jack if necessary and put the nut back on and tighten.
The lower ball joint is pressed in. Tie the spindle out of the way and brace the lower control arm with some blocks or the jack if you have to. A few whacks with a hammer should pop the joint out. Clean the hole out lightly, just to remove loose rust and dirt. Put the ball joint, minus the grease fitting ,,in the hole and use the jack with a block of wood, to put it in place.You may have to fiddle with the spindle to make sure it is lined up. I've never had any trouble using a 1ton trolley jack and the weight of the truck to put the lower ball joint back in. Replace the nut and grease fitting.
The new ball joints will probably come with cotter pins, use them. Make sure the new joints are tight or they will wear the holes in the spindle. Don't forget to grease the new joints. Hope this helps.

Posted on Jul 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the best method for changing the lower ball joint/control arm on a 2004 ford freestar?


The lower ball joint original is riveted into the lower control arm. If you can get to the lower control arm with a drill then the rivets can be drilled out and the joint removed . I find it quicker to remove the lower arm and do the job in a vice on the bench. Replacement ball joints will come with grade 8 bolts ( auto engineering quality) and will simply bolt into place using the holes for the rivets. So the procedure will be to jack the vehicle and place securely on jack stands. remove the wheel, remove the ball joint nut and using a ball joint removing tool drive the ball joint taper out of the support arm ( strut) Remove the inner pivot bolt ( remember to note the position of the lock washer as it is encentric and alters the wheel alignment) put the arm in a vice and carry on.

May 10, 2014 | 2004 Ford Freestar

2 Answers

Lower ball joint


how?, its in the FSM book
log in to alldata.com and read.
or here.
for 4 bucks
just $4
https://suzukipitstopplus.com/Products/1177-2002-aerio-service-manual.aspx

to read or if savvy DL.

google it
youtube it yet?

Jan 20, 2014 | 2002 Suzuki Aerio

1 Answer

I have 2002 grand vitara. It has a problem with ball joints. Do ball joints come as an assembly?


fsm quote
The lower ball joint is serviced with the lower control arm as an assembly. Refer to lower control arm.

Nov 22, 2013 | 2002 Suzuki Grand Vitara

1 Answer

Front end bushing and ball joint do you need to change upper and lower bushings at same time and how hard is to them


It's not required to change the upper and the lower at the same time. However it will save you time if you do them both as if one is going out the other will soon.
The actual job is not that difficult but you may need a pickle fork or a ball joint removal tool to disconnect the ball joints from the steering knuckle. You will also need a ball joint press to remove/install the ball joints. You may also need a strut spring compressor. You can rent these at an auto parts store.
Basically you have to do the following -loosen lug nuts -jack the vehicle up and place on jack stands -remove wheel -remove upper ball joint cotter pin and nut -remove lower ball joint cotter pin and nut -with pickle fork/ball joint removal tool remove both upper and lower ball joints from steering knuckle -disconnect tie rod end from knuckle (optional depending on clearance) -disconnect strut (be sure to install strut spring compressors) -with ball joint press you will need to press both ball joints out (you also use the press to install ball joints)
Installation is reverse of removal.
For exact instructions you can buy the manual for about $20 or go to autozone.com, register, and view the manual on their site for free.

Jan 26, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

Driver side lower ball joint


There is a special tool which you need to press the ball joint out. Most national auto part chains have a free loan-a-tool. Autozone carries it, you will need to front about $125 to rent it, which will be refunded once you return the tool.

Jan 12, 2010 | 1998 Lexus Gs 300

1 Answer

Upper and lower ball joints


Jack the truck clear of the ground and let the wheel assembly hang. After you remove the tire place your jack under the lower control arm so it's firm. Remove the cotter pin, if you have one and loosen the big nut almost off. Wedge a "pickle fork" between the control arm and the spindle and give it a belt with a hammer until the ball joint pops. Raise the jack so you can undo the nut easily and separate the control arm and spindle.
The upper ball joint is riveted or bolted in. Grind the rivets or use a cold chisel and remove the ball joint. Clean up the area with some sandpaper, dirt , loose rust, etc.and put the new joint in. Put the spindle back on using the jack if necessary and put the nut back on and tighten.
The lower ball joint is pressed in. Tie the spindle out of the way and brace the lower control arm with some blocks or the jack if you have to. A few whacks with a hammer should pop the joint out. Clean the hole out lightly, just to remove loose rust and dirt. Put the ball joint, minus the grease fitting ,,in the hole and use the jack with a block of wood, to put it in place.You may have to fiddle with the spindle to make sure it is lined up. I've never had any trouble using a 1ton trolley jack and the weight of the truck to put the lower ball joint back in. Replace the nut and grease fitting.
The new ball joints will probably come with cotter pins, use them. Make sure the new joints are tight or they will wear the holes in the spindle. Don't forget to grease the new joints. Hope this helps.

Jul 13, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2000 Ford Taurus. How do I change a ball joint?


Lower Ball Joint Inspection
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Raise and support the vehicle.
  3. Prior to carrying out any inspection of the ball joints inspect the wheel bearing.
  4. Have an assistant pull inward and outward on the top and the bottom tire. Mount a suitable dial indicator and measure the movement between the ball joint and the lower arm. If the movement is at or exceeds 0.03 in. (0.75 mm) install a new ball joint.
167f4af.gif

Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove the knuckle from the front suspension.
  3. Remove the snap ring from the ball joint.
  4. Press the ball joint out of the knuckle with a suitable ball joint press and adapters.
656c3d7.gif

Jul 04, 2009 | 2000 Ford Taurus

1 Answer

Lower Ball Joint


You will have to remove it and replace it with a new one. The general steps for doing that is: 1)remove the tire 2)remove the caliper and rotor 3)remove the outer tie rod from the spindle 4)remove the axle nut 5) remove the cv axle 5)remove the nut on the ball joint 6) bang ball joint out and press in a new one. Then reassembly is exactly the reverse as disassembly.

Jun 10, 2009 | 1995 Nissan Pickup

1 Answer

Is the lower ball joint easy to repair?


You need a hydraulic floor press.........with special tools, after removing the conrol-arm from the car!
Get it off, and take the whole thing to a machine shop with the new ball-joint. Make sure you get a wheel alignment when you're done........or you'll be buying tires soon.

May 27, 2009 | 1995 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...