Question about Cars & Trucks

Open Question

How do I replace the headlight bulb in my 2010 Kia soul

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
turboKia
  • 55 Answers

SOURCE: How do you replace a Drivers side headlight bulb 2006 kia spectra

Helps to remove the battery, but small ahbds can do it.

Directly behind the lens is a big round cap ... twist it off. The bulb is held in place with a spring that locks in to a notch in the holder. When handling the new bulb, don't touch the glass. The oil from your skin will cause it to shatter when turned on.

Posted on Oct 23, 2009

Ad
  • 1986 Answers

SOURCE: replacing my headlight bulb in my kia amanit 2004

  1. Open the hood of your KIA Amanti and look behind the headlight that has gone out. Locate the round knob on the back of the headlight.
  2. Turn the knob counterclockwise 1/4 of a turn and gently remove it from the back of the headlight. Carefully remove the electrical cable within the headlight housing that is attached to the back of the headlight bulb.
  3. Locate the metal clip that holds the light bulb in place by pushing the clip arm straight in and sliding it down. Remove the bulb from the headlight housing.
  4. Replace the old headlight bulb with new bulb. Secure it by sliding the metal clip up to hold the bulb in place. Reattach the electrical cable and replace the round knob to the back of the headlight housing.
  5. Turn on the headlights to verify that they are in working order.

Posted on Nov 03, 2009

  • 1 Answer

SOURCE: how do you change the right front headlight bulb on a kia sedona

Remove the headlight assembly. Just remove the 3 bolts with a 10 mm socket and pull it out so you can disconect the wire harness. After that pull the whole assembly out and unscrew the bulb cover. The bulb is held in with a spring clip.

Posted on Dec 31, 2008

  • 111 Answers

SOURCE: how do i replace headlight

REMOVE THE COVER BLACK COVER HELD IN BY PUSH TABS AND THERE SHOULD BE COVERS ON THE BACK OF THE HEADLAMPS JUST TWIST AND RELEASE THE CONNECTOR AND PUSH AND RELAESE THE METAL PIN AND YOU THEN CAN REMOVE THE BULB

Posted on Jan 16, 2011

renselff
  • 75 Answers

SOURCE: where is the fuel filter located on a 2010 kia soul

the fuel filter itself is attached to the fuel pump inside the fuel tank.

Posted on Feb 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Low beam on driver side nit working 2010 kia soul


You need to replace the lamp as the low beam filament has broken. The lamp could be a double filament lamp, high & low. Or your car has separate lamps for each beam. Either way replace lamp.

Jul 08, 2017 | 2010 Kia Soul

1 Answer

How do you adjust the headlights on a 2010 Kia Soul?


Not sure about your car but my Buick has little screws where you can set the lights up or down. I had to get a special type of screw driver to set them.

Feb 03, 2017 | Kia Cars & Trucks

1 Answer

Thermostat location on 2010 Kia Soul


follow the top rad hose to engine.

Oct 22, 2013 | 2010 Kia Soul

1 Answer

Inertia switch location on a 2010 kia soul


Fuel Safety Shut Off Switch

Only on Ford Products

Dec 18, 2012 | 2010 Kia Soul 2.0

1 Answer

2010 Kia soul car alarm won't stop blinking.


I think one of your door latches was not closed all the way. Check that first.

Aug 03, 2011 | 2010 Kia Soul

Not finding what you are looking for?

Open Questions:

0 Answers

My 2007 Dodge Ram 1500 4X4 with the 5.7 Hemi engine threw me for a loop yesterday. Stay with me on this as it gets weird. First the engine shut down as did the tach. Then started back up as I coasted down the road (in Mexico of all places). Next it did the same thing again but in addition the cruise would not work and the overdrive didn't work (usually @ 2000 RPM at 60 then the tach showed 2500 RPM. Sure enough by engaging the button on the shifter no change in RPM. Then the engine shuts down, tach inop, OD inop, cruise inop, and the check engine light comes on. Then (it gets better) all of the above happens and I coast to a stop. Shut the ignition off, turned it back on and the cruise works, the overdrive works but the engine shuts down BUT the tach is now working. Long story longer I limp back to Green Valley, AZ with the truck and run the codes and the only code is a P0300 (random cylinder misfires within a predetermined period of time (No S#@t). Also was able to determine the following codes. P0339 (crankshaft position sensor intermittent, P1128 Closed loopfueling not achieved-bank 1 as well as P1129 (the other bank). I'm leaning towards replacing the ECM. Could it possibly be the IPCM (integrated power control module)? OR do I have a loose connection somewhere? It seems the problem gets worse when I go over rough roads (about all of Mexico is ROUGH roads. LOL) Call me "Looking for answers before I pull the rest of my hair out".

May 26, 2018 | Dodge Cars & Trucks

Cars & Trucks Logo

Related Topics:

1,372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13735 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...