Question about 2006 Mercedes-Benz Mercedes Benz CLS500

Open Question

How to connect my cell phone to my 2006 Mercedes CLS 500

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 869 Answers

SOURCE: How do you reset maintenance indicator on a 2006

u can check cls manual or take it to a dealer.

Posted on Feb 15, 2011

Ad
  • 869 Answers

SOURCE: I have a 2006 CLS 500...44,500 miles...due for

service details are given in a booklet that comes along with cls. u'll get all the information there.

Posted on Feb 15, 2011

  • 2187 Answers

SOURCE: how to reset the srs

Before resetting the SRS I would advise to take note of the error. You would need an OBD scan tool for you to get the errors and to reset the SRS.
On the fuse box found on the driver side of the car you should see the port for the OBD tool. Connect the OBD tool. Turn the key to the 'Run' position (the one before 'start'). List down the codes and make necessary repairs with the shop. This also resets the SRS if you wait for the light to go off before disconnecting the OBD scan tool.

Posted on May 14, 2011

  • 510 Answers

SOURCE: what is the meaning OBD to reset SRS for CLS 500

You need a on board diagnostic scanner plugged in to locate fault
SRS is safety restraint system, fault is usually seat belt sensor
A good local auto electrician will locate the problem
Main dealer will cost a lot of money
Good luck Barry

Posted on May 14, 2011

Testimonial: "thanx"

eddie-50
  • 66 Answers

SOURCE: how do i check oil

Hi claude?
There is no deepstick for the engine oil. You can check your oil level from the steering wheel controls. Turn the ignition on, do not start the engine. press the page button till the milage and the trip miles are displaied. press the arrow button up or down till it comes up with engine oil level check, and wait till the engine has meassured the oil level.
If you want to change the oil, you need to measure how much oil comes out of the engine and put the same amount back in.

Posted on May 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mercedes CLS 500 Why is my door ajar light is on but door is closed


sounds like the door switch is not working find out which door is causing this, Close all the doors and One at a time open a door find the button on the door jamb and press it in, See if the door ajar light goes out, If it does, The door is not pushing the button in enough to turn it off. you can attach something to the door where the button hits or extend the button and make it hit the door.

Feb 16, 2015 | 2006 Mercedes-Benz CLS 500

1 Answer

Where can I find a fuse chart for a 2006 Mercedes CLS ?


Check 25A FUSE 9 in the rear SAM control module with fuse and relay module.

Sep 07, 2014 | 2006 Mercedes-Benz CLS 500

1 Answer

Cls 500 is leaning to left u can hear a whistling sound when rising


I just bought a preowned CLS 500 and recently noticed the same issue. Whistling after I start and stop the engine. "Car too low" notice if I hit a speed bump too fast. Etc.
I'm guessing it has something to do with a leak in the air suspension.

Did you ever resolve your problem?

Jun 27, 2012 | 2006 Mercedes-Benz Mercedes Benz CLS500

1 Answer

Mercedes cls 500 2006 battery dead but is now recharged lights work but moter will not turn over


starter motor could be bad motor could be locked up pulley could be locked up there arealot of things it could be just elimate the quick and easy problems first

Apr 07, 2012 | Mercedes-Benz CLS500 Cars & Trucks

1 Answer

What is the meaning OBD to reset SRS for CLS 500 2006 and how i can reset it?


You need a on board diagnostic scanner plugged in to locate fault
SRS is safety restraint system, fault is usually seat belt sensor
A good local auto electrician will locate the problem
Main dealer will cost a lot of money
Good luck Barry

May 14, 2011 | 2006 Mercedes-Benz Mercedes Benz CLS500

2 Answers

How do you reset maintenance indicator on a 2006 cls 500 mercedes


There is only 2 ways.....1 take it in to a qualified repair shop that has the diagnostics tool or buy it yourself from Autozone or NAPA. ETC. Hope this is the info you need. You might be able to find a friend that has one. They cost anywhere from 200-300 dollars.

Jan 21, 2011 | 2006 Mercedes-Benz Mercedes Benz CLS500

2 Answers

What is the cost of a D service on a cls 500 benz..


$500 - rotate tires, oil, tire pressure, fluids, lube doors, etc.

Apr 20, 2009 | 2008 Mercedes-Benz Mercedes Benz Cls Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...