Question about 2008 Peugeot 207 Sport

Open Question

Peugeot 2009 207 diesel. The fualty depolution warning has appeared

Car went into limp for a while the engin management light is on

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: peugeot 206 1.9 diesel

fuel diesel problem

Posted on Oct 29, 2008

Ad
  • 99 Answers

SOURCE: engine management light is on

The car will need to be put on a diagnosic machine to point out exactly why the engine has gone into limp mode, but if it is still running it could just be down to a sensor, Hope this helps

Posted on Dec 04, 2008

  • 166 Answers

SOURCE: peugeot 406 hdi

very hard to diagnose these cars go to dealer and get checked it is the only way to fix these kind of issues

Posted on Dec 20, 2008

  • 89 Answers

SOURCE: Engine management light is on

u will have to get it on a computer to diagnos the problem as soon as possible

Posted on Jul 13, 2009

  • 4 Answers

SOURCE: peugeot 406 hdi electronic immobiliser warning

did you try the spare key? are you sure it is an immobilizer light? what does the warning light look like, can you describe it? replacing the battery in the key will not help as it is not needed for the recognition of the key(this is done by an induced current). 

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

White smoke from my exhaust on my peugeot 407 hdi sw and says depolution system faulty


Try to replace the dpi filter...then follow this method to "remove" the code after you replace the dpi filter:
try to reset the maintenance computer. To do that, remove the car key. Press continusly on the "check" botton on the dash board. Put the key in and switch to on, but don't start the car. Wait 10 seconds (on screen 10-9-7...-0). Nowthe maintenance computer go to 20,000 and erase all old warning report. If the engine light and the "depolution" warning keeps showing up after that, it means there are still fuel related problems. make sure you are using the right fuel and fuel filter!!!. Don't use cheap fuel/filter, like at supermarket store, etc..get them from real gas station/auto part store...

Nov 27, 2013 | Cars & Trucks

1 Answer

My peugeot 407 hdi sw is saying depolution system faulty showing engine management light and blowing smoke from exhaust when started


chek for a collapsed catalytic converter and/or a clogged exhaust system...if it only smokes when 1st started, it could need valve seals...chek for clogged charcoal canister too if equipped...

Nov 27, 2013 | Cars & Trucks

1 Answer

My peugeot 407 hdi 1.6 depolution system faulty came on and engine managment light . Car blew smoke now won't start what is it


could be a lot of things, blocked dpf filter, egr valve stuck open, injector stuck. need to have it plugged in to see what faults the ecu is holding.

Nov 27, 2013 | Cars & Trucks

1 Answer

My peugeot 407 hdi 1,6 sw depolution system came on and engine managment light ! It blew smoke so I stopped car won't start what causes this


Sorry dealer only and its going to cost about a 1000 pounds at least although i suspect that the timing belt broke as they still start even with this poloution light on

Nov 27, 2013 | Cars & Trucks

1 Answer

My peugeot engine management light comes on and screen says engine depolution system faulty what does this mean ?


The car will have to be plugged in for diagnosis. There's no way of knowing how expensive this will be to sort out?
_________
Launch X431 Creader VIII

Jun 05, 2013 | Cars & Trucks

1 Answer

Peugeot207 1600 Diesel HDI goes into limp mode


This make is not sold in the USA so have little or no info on it. Sorry

Jun 06, 2012 | Cars & Trucks

1 Answer

Jag xtype 2.0D 2004 Glow plug light flashing.Engine malfunction light on .No loss of power.Hhappened just after refuelling


jaguar x-type 2ltr diesel 2004 the glow plug warning light flashing, was told dirty fuel on fault code all fuel changed and filters. No problems for 20 miles untill engine was put under power on high revs went into limp mode, warning light glow plug falshing again? any ideas thanks.

Feb 09, 2011 | 2004 Jaguar X-Type

1 Answer

Hi, I'm getting code p1445 (additive level too high) after I refill additive (fit almost 4 lit.). I try to reset counter to zero but ecu reply there is no communication with ecu and on display message...


recently had similar problem 307 55 hdi engine code RHR getting p1445 + p1435. Hooked car up to launch 431 code reader got p1445 purge flow sensor circuit high input. pa435 a/c ref temp circuit range/performance no contact. Then hooked to snap on ethos p1445 diesel additive system quantity too high. p1435 diesel additive system incorrect message from can bus. checked tank level 1/3-1/2 tank about right for 55k fired pump by shorting briefly appeared to work as youd expect. few hours later after dismantleing most of car looking for depolution ecu stumped ! next day dropped in to local peugeot dealer who i know well after a conflab they agreed these are common codes easy solution! The depolution ecu is found either beside the passenger seat (left) against the sill or depending on where its built behind the fuse board/glove box (where this one was) just remove felt under glove box look up with torch behind fuse board youll see big relay type unit with slide out release (red) unplug clean (toothbrush w40) apply vv slight pressure to pins to adjust contact, refit, clear codes job done !! Common problem apparently worked for me easy & simple place to start !

Jan 18, 2011 | Peugeot Liberte Cars & Trucks

1 Answer

Engine management light is on


The car will need to be put on a diagnosic machine to point out exactly why the engine has gone into limp mode, but if it is still running it could just be down to a sensor, Hope this helps

Dec 04, 2008 | 2005 Peugeot 405

Not finding what you are looking for?
2008 Peugeot 207 Sport Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...