Question about 1991 Jeep Wrangler

Open Question

How to replace slave cylinder on a 1991 jeep wrangler

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 25 Answers

SOURCE: hydraulic clutch for jeep wrangler 2000

The bleeder screw is located on top of the slave cylinder. It will not work right until it is properly bled.If the reservoir runs dry, you will have to start all over. Have an assisstant pump the clutch pedal 3 times with the bleeder screw closed...then hold the pedal down and open the bleeder screw. Don't release the pedal until the screw has been retightened...continue this process untill no air bubbles come out of the bleeder screw....don't let the resevoir run dry...Please rate this...

Posted on Sep 18, 2008

Ad
  • 33 Answers

SOURCE: 1994 Jeep Wrangler 4cyl - Bleeding slave cylinder

This is not a bleeder hole, this is a weep hole like in a water pump to see when there is seepage past the seals.

Bench bleed the system. With the master cyl. line and slave cyl assembled, place the master cylinder in a vise, fill the master cyllinder. actuate the slave cylinder back and forth lower than the master cyl. This will allow the air to escape upwards back into and out of the master cyl.
Once bled the system can be installed.

Good Luck

Posted on Oct 02, 2008

bigc73542
  • 108 Answers

SOURCE: Jeep Wrangler 6 cyl. idles up and down

Have your oxygen sensor checked, one of the symptoms of a faulty oxygen is an up and down idle.

Posted on May 04, 2009

emissionwiz
  • 76118 Answers

SOURCE: 1991 jeep wrangler clutch

U have what is called a hydraulic clutch, one of the hydraulic cylinders hs failed, there is a master and a slave cylinder. The most likely and most common cylinder to fail is the slave cylinder, this requires the transmission to be pulled out to replace it. the art is around $125.00, while the trans is out u might as well replace the clutch, the labor is about the same. Here is a picture of the part, let me know if u can see it.



1abd4ec.jpg

Posted on May 13, 2009

  • 6982 Answers

SOURCE: replace 1995 jeep wrangler catalytic converter

If it has flanges on both ends, just unbolt it and replace. If it has welded pipes you will need to cut it off and use adapter sleeves and clamps. Really not rocket science...at worst, you may need to remove the hangars on the rear portion of the system to get enough room to install.

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1991 jeep wrangler the clutch fluid keeps getting real low


clutch fluid level droppin means that ur clutch master cylinder is leaking,u can check by looking inside car where pushrod goes thru firewall to see if its wet with brake fluid where rod comes thru wall inside car, a wet ,stained carpet.the other possibility is ur clutch slave cylinder located at side of ur transmission,usually drvr side is leaking fluid.if this is the case u will notice clear brake fluid at the bottom center of ur trans,right where it butts up towards ur engine. anyhow its a good idea to replace both pieces at same time to avoid any further issues with clutch pedal. good luck hope this helps

May 01, 2011 | 1991 Jeep Wrangler

1 Answer

How do you check the clutch fluid on 1991 Jeep Wrangler?


There should be a small master cylinder for the clutch right next to the brake master cylinder, mounted more towards the fender. Remove the top cover and look inside. Regular brake fluid is used in the clutch system. If it's low, likely you have a leak so check where the rod goes through the firewall under the dash, the line itself and the slave cylinder (some are outside the bellhousing, others are inside and fluid will leak from the bottom of it.

Jun 15, 2010 | 1991 Jeep Wrangler

3 Answers

!991 Jeep Wrangler clutch pedal loses pressure. I have to pump it to get enough pressure to shift. I keep it full of brake fluid. I can see no leaks. Thanks for any help.


leaky slave or master cylinder - if you have someone listen to the slave cylinder while you press the pedal is should "squelch" if there is air in there, if the slave cylinder doesn't make a squelching sound then the master cylinder or a hydraulic line between the two cylinders is leaking - slave cylinder isn't very expensive but the master cylinder can be rather pricey. and any good parts shop or motor-factor can source or make-up a new hydraulic line if it is the line itself that is leaking.

Jan 27, 2010 | 1991 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

4 Answers

1991 jeep wrangler clutch


U have what is called a hydraulic clutch, one of the hydraulic cylinders hs failed, there is a master and a slave cylinder. The most likely and most common cylinder to fail is the slave cylinder, this requires the transmission to be pulled out to replace it. the art is around $125.00, while the trans is out u might as well replace the clutch, the labor is about the same. Here is a picture of the part, let me know if u can see it.



1abd4ec.jpg

May 13, 2009 | 1991 Jeep Wrangler

2 Answers

1991 jeep wrangler not shifting into gear could this be clutch


I would first bleed the tranny lines, if that doesnt work then your tranny is out and need to get it replaced. FYI with Jeep Wranglers, It is better to get a new transmission then to rebuild them

Feb 09, 2009 | 1991 Jeep Wrangler

1 Answer

How do you bleed the clutch in a 1991 Jeep Wrangler?


If replacing just the fluid, you should gravity bleed it by opening the valve at the side of the transmission where the line goes in to connect with the slave cylinder. Be sure to stand by and keep the tiny reservoir from going empty during bleeding, or you just make things worse. Assume you replaced parts. Is this right or wrong?

Or are you just trying to restore performance in a poorly operating system? Would help TONS to know these details, and how much you know about bleeding, etc. If you are trying to bleed a new slave cylinder, it can take 600 to 1800 pumps of the clutch pedal sometimes to clear it out manually. If you want instructions on how to bleed in with vacuum assistance, please post request comment to that effect.

Talk to you soon. TT

Feb 06, 2009 | 1991 Jeep Wrangler

1 Answer

Clutch Pedal to Floor


slave cylinder needs replaced

Nov 12, 2008 | 1991 Jeep Wrangler

Not finding what you are looking for?
1991 Jeep Wrangler Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...