Question about 1991 Eagle Talon

1 Answer

Need to remove stuborn bolt - 1991 Eagle Talon

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Eagle Master
  • 75,005 Answers

Heat it with a propane torch.

Posted on Dec 11, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing rear rotors on a 2004suzuki verona


this is covered in the FSM, buy one.
or log in to alldata.com
or suzuki pit stop plug (google them )
read the brake chapter?
same as the front, it is, so never done brakes before, is that it?
the only uniqueness is step4
all steps work on most cars until step 4.

  1. jack it up, use stands
  2. wheel off
  3. calipers off, and tied up per FSM (they unbolt.....)
  4. remove secret bolt at rotor center. see it? at 7PM
  5. the plug at 11am , is for inserting a 8mm screw to force off stuborn rotor, seen on most suzuki's 92 to now.l
  6. now remove rotor.


2bd852d6-a247-43dd-9473-382f9317ba01.jpg

Oct 12, 2014 | 2004 Suzuki Verona

1 Answer

How can I remove the dipstick tube?


the bottom of the dipstick tube is just pushed into the block, you might have to use some brake cleaner to loosen it up if its being stuborn

Feb 22, 2013 | 2004 Nissan Sentra 1.8

1 Answer

REMOVE ROTORS FROM CANYOM


look at the face of the rotor between wheel studs there should be a small threaded hole it usually takes a 12 mm bolt it works like a press thread the bolt in and it should press rotor off, if it is stuborn tap on the side of the rotor (not the edge the side of ur rotors hub flange)
good luck

Nov 05, 2012 | 2006 GMC Canyon

1 Answer

I cant get the front rotors off on my 05 caddillac cts


removed caliper and pads removed caliper mount if in way
rotor should free float on hubs they may be rusted tight to hub
if you are replacing them just hit them in the central part (around lug nuts studs)
they can be stuborn to free up
if you were reusing them you will need a puller to pull them off
if your replacing them have a look at the new ones you will see how they free float

Apr 02, 2011 | Cadillac CTS Cars & Trucks

1 Answer

How do you take off panel to change the headlights?


Start at the Bottom by Removing Screws that Hold LOWER PANNELS, Move your way up and The Upper Pannels have SNAP IN FASTENERS that Afix them to the dash And the FASTENERS CAN BE STUBORN and Be REALY Tight with HOLDING POWER but just PULL HARD, Also Be SURE there are NO SCREWS on the Bottom of the UPPER PANNELS

Apr 24, 2010 | 2005 Chevrolet Equinox

1 Answer

Can i replace bal joint on a ford f150 without puting truck on a lift. I have a jack and a pair of ramps.I dont have money to go to a repair shop so what tools do I need


you need a ball joint press cost about fitfty bucks if it is rusty you will need a set of torches they can be stuborn you will also need large pair of snap ring pliers

Mar 24, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Stuborn Windows 2002 Audi A6


your window regulator is going bad, you will need to replace it. I have the A4 and I have replaced both front window regulators myself. If you plan on doing it yourself you will need to get a drill as Audi uses Rivets to hold the regulator in place. you can then replace the rivets with nuts and bolts.

Sep 30, 2009 | 2002 Audi A6

2 Answers

I need to remove inside door panel and replace door cylinder


There is a Pannel SNAP Removal Tool To Get those Stuborn Snaps that Are Holding it on, Lock Cyls. are self Explanitory when you get to them

May 31, 2009 | 1990 Honda Accord

Not finding what you are looking for?
1991 Eagle Talon Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Stewart Dibbs

Level 2 Expert

267 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...