Question about GMC Sonoma

Open Question

Clutch pedal is broken

When i was driving i heard something break and my clutch pedal droped to the floor and my truck stalled. after changing the clutch and trying to bleed it i noticed that the linkage from the master cylinder was off and than looked further up and moved my clutch from side to side and saw that it was broken.. is this a easy fix and would i have to take my dash out to get at it?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L

my rodeo had the same problem i corrected it by bleeding the slave cylinder. and is located on the driver side on the gearbox you will find it if you follow the line from the master cylinder down to the gearbox and if that helps but happens again it might have to be replaced.

Posted on Dec 29, 2008

Ad
  • 51 Answers

SOURCE: clutch cylinder inside car is it broke

you have to bleed the air out of it. If there is not fluid leaking from the master cylinder on the firewall.it can leak on the inside of car or the out side if the master cylinder is bad.first make sure the reservoir stays full then open the bleeder on slave cylinder. this is called gravity bleeding. once fluid comes out, tighten bleeder, pump pedal one time loosen bleeder while holding clutch pedal down and then tighten. do this repeatedly until no air comes out. you can pump pedal several times,then hold and bleed however you like but I have better luck with individual pumps. just make sure that the lines hooked to slave cylinder are tight and there are no air leaks. and that the line does not go below the slave cylinder because sometimes air gets trapped in the lowest part of system.

Posted on Jan 12, 2009

co7196
  • 3433 Answers

SOURCE: 1996 nissan maxima clutch sticks to floor

yes, Briong the pedal up where it belongs, then open an fill your master cylider. Then go below and open the bleeder intil the fluid runs/drips steady and free of any bubbles. Do not pump the pedal. When only fluid comes out, tighten/close the bleeder and give it a try. Good Luck. If peal dives again, replace the master cylinder.

Posted on Jul 11, 2009

mecanica03
  • 905 Answers

SOURCE: bleed brakes on 2003 toyota corolla

i try to help you, firts refill brake fluid container,open purge valve in one wheel front only,wait few minutes when drops fluid, close this valve and open other wheel, same procedure, finally repeat this in each 4 wheels

Posted on Jul 14, 2009

  • 133 Answers

SOURCE: 1992 Chevy Silverado - Clutch Slave Cylinder broke

JB weld will not work get it welded by a pro with the proper hi frequency welder otherwise you will have to replace the box ,and yes get a new cylinder ,hope you get sorted

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Mazda MX6 Clutch pedal has no push back from floor but still shifts


I am not a mazda guy but it sounds like the pressure plate is bad. Have you check the clutch linkage to be sure something did not slip or break. If so I would be looking at the clutch pressure plate.

May 18, 2017 | Mazda Cars & Trucks

1 Answer

Mg Rover Manual 1600 1800cc Turbo


It might be a broken finger on the pressure plate for the clutch and that is allowing the pedal to stay on the floor and not return to the top.

May 19, 2017 | Cars & Trucks

1 Answer

I pulled up at a set of lights & the clutch pedal


broken release clutch bearing. You have to change the clutch unit of your car.

Sep 15, 2012 | Cars & Trucks

1 Answer

Clutch pedal straight to floor


If you put the trans in neutral and depress the clutch pedal it should still start.
The clutch is hydraulic, so there should be something connecting the pedal to the master cyl and the slave cyl to the clutch disk.

Jun 26, 2012 | 1991 Honda Accord

1 Answer

Clutch pedal goes to the floor and doesn't work. Heard something break. What do I need to look at?


The rod from the peddle to the master cylinder if it sounded inside the cab. I suppose either cylinder may have broken (is there still fluid in the reservoir?) and perhaps the rod on the slave cylinder.

Sep 23, 2010 | 1991 Toyota Pickup

2 Answers

Clutch pedal sticks to the floor; the brake reservoir was low


I believe your pressure plate is broken and at a minimum will have to be replaced along with the clutch disk.

Jul 04, 2010 | 2006 Ford Fusion

2 Answers

Clutch pedal went to the floor but did not come back up. Heard something 'pop' when pushing in clutch last night. Got home, then tried to start car this morning and clutch made a 'pop' sound again when...


there is a plastic clip that connects the clutch pedal to the rod that goes to the master cylinder, chances are that it let go. Bad thing is that it is only available from GM along with the rod. It is around 50

Oct 16, 2009 | 2003 Oldsmobile Alero

2 Answers

Clutch will not depress on 996 turbo


sounds like you have hammered your clutch. Replacing it would be the easiest thing

May 31, 2009 | 2002 Porsche 911

1 Answer

Emergency break pedal stuck to floor, but break is disengaged


sounds like your brake cable has broken or there is something damaged in the pedal assembly.........try pulling on the release handle and move the e-brake pedal back to its off position by hand at the same time.(you may have to tie it in this position to keep it up)If that doesnt work there is a sensor on the pedal assembly that you should be able to bypass by either disconecting the wire(1 wire system) or connecting the two wires together (2 wire system)Especially if your truck is a standard the e-brake is an important safety feature,so if these steps fix the light and dinging problem you should still take the steps to have it repaired.
hope this helps.........Good Luck!

Dec 09, 2008 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...