Question about 2002 Chevrolet Malibu

Open Question

Installing anti-rattle clips on 2002 malibu - 2002 Chevrolet Malibu

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 491 Answers

SOURCE: 2002 malibu anti theft problem

With the car RUNNING cut the yellow wire to the ignition switch from the group of three wires.
Make sure the car is RUNNING when the wire is cut.
Tape the ends and thats it.....the car will start first time from now on....as long as you don't mind not having anti theft.

Posted on Sep 17, 2009

Ad

SOURCE: how to replace anti-rattle clips in a 2002 chevy

You'll need to take out the pads agaon and clip the anti rattle plates to the back of the pads and then reassemble, the same way you did before....Don't open the brake lines or nipples just push the pistons into the cylinders with a convenient lever, so you have room for the new items to fit....Once fitted remeber to pump up the brakes before you start or move the vehicle....Regards Johngee

Posted on Oct 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rattle noise coming from front of my 2002 Chevy


FRONT BRAKE PADS ARE LOOSE IN THE CALIPER. MAY HAVE SOME OF THE ANTI RATTLE CLIPS MISSING OR CHEAP PADS

Sep 26, 2014 | Cars & Trucks

1 Answer

I have a 2000 chevy malibu. I recently replaced the front brake pads. After this when driving down the road when i hit bumps something in the frontend rattles, i can hear and feel it.. when i hit or ride...


A loose pad could do it.
Check the pad anti-rattle clips again. The pads should be snug in the calipers. Its possible the new pads are not the exact same shape as the old ones.

Jan 14, 2013 | Cars & Trucks

1 Answer

When I turn to the right my car squeaks


Did you install the brake pad spring anti rattle clips? Many leave this out.

Nov 05, 2012 | 2002 Pontiac Sunfire

1 Answer

NOISE COMING FROM POSSIBLE BRAKES


Brake pad anti-rattle clips not properly installed more than likely.

Jul 24, 2012 | 2002 Chevrolet Suburban

1 Answer

How to change rear barke shoes


Brake Drums & Brake Shoes Removal & Installation To Remove:
Rear Drum Brakes kia-09-18-7627.gif

  1. Raise and safely support rear of vehicle.
  2. Release parking brake.
  3. Remove rear wheel assemblies. NOTE: If brake drum is stuck, install two 8 mm bolts into threaded holes and tighten evenly.
  4. Remove top return spring, front and rear shoe spring clips and hold-down pins.
  5. Remove anti-rattle spring and adjuster spring. NOTE: Note position of operating lever prior to removal.
  6. Remove bottom return spring.
  7. Remove clip and washer and detach parking brake cable from rear shoe.
  8. Remove brake shoes.
To Install:
  1. Lubricate all brake shoe contact points with appropriate grease.
  2. Place operating level into position on hub.
  3. Install rear brake shoe and connect parking brake cable to rear shoe with washer and clip.
  4. Install front brake shoe and install bottom return spring.
  5. Install hold-down pins and spring clips.
  6. Position operating lever and install top return spring.
  7. Install anti-rattle spring and adjuster spring.
  8. Install brake drum and screws.
  9. Adjust brakes and install rear wheel assemblies.
prev.gif next.gif

Jan 21, 2011 | 2003 Kia Spectra

1 Answer

I need to know how to change the front brakes on a 94 jeep grand cherokee laredo.


  1. Raise and support the vehicle safely using jackstands. Remove the wheel(s) on the side to be worked on.

NOTE: Removing a small amount of brake fluid from the master cylinder using a turkey baster


zjlimited_10.jpg

Fig. 4: Tighten the C-clamp until the piston reaches the bottom of its bore


zjlimited_11.jpg

Fig. 5: Remove the caliper mounting bolts


zjlimited_12.jpg

Fig. 6: Slide the caliper off the brake rotor

  1. Drain a small amount of the brake fluid from the front reservoir using a suction gun or a turkey baster.
  2. Place a C-clamp on the caliper so that the solid end contacts the back of the caliper and the screw end contacts the metal part of the outboard brake pad.
  3. Tighten the clamp until the caliper moves far enough to force the piston to the bottom of the piston bore. This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly
zjlimited_13.jpg

Fig. 7: Support the caliper so that no tension is placed on the brake hose


zjlimited_14.jpg

Fig. 8: Hold the anti-rattle clip while removing the outboard pad (4)


zjlimited_15.jpg

Fig. 9: Removing the outboard brake pad


zjlimited_16.jpg

Fig. 10: Remove the inboard pad and anti-rattle clip


zjlimited_17.jpg

Fig. 11: Removing the inboard brake pad


zjlimited_18.jpg

Fig. 12: Removing the anti-rattle clip

  1. Remove the C-clamp.
Do not push down on the brake pedal or the piston and brake pads will return to their original positions up against the rotor.
  1. Remove the caliper mounting bolts. Tilt the top of the caliper outward and lift it off the rotor.
  2. Hold the anti-rattle clip against the caliper anchor plate and remove the outboard brake pad.
  3. Remove the inboard pad and the anti-rattle clip. Be sure that the support spring is removed with the inboard pad.
zjlimited_19.jpg

Fig. 13: Install the support spring onto the shoe of the inboard brake pad


zjlimited_20.jpg

Fig. 14: Installing the inboard pad


zjlimited_21.jpg

Fig. 15: Piston extension on new and worn brake pads

  1. Use a piece of wire to support the caliper so that no tension is placed on the brake hose. Do not allow the caliper to hang by the brake hose.
To install:
  1. Clean all the mounting holes and bushing grooves in the caliper ears. Clean the mounting bolts. Replace the bolts if they are corroded or if the threads are damaged. Wipe the inside of the caliper clean, including the exterior of the dust boot. Inspect the dust boot for cuts or cracks and for proper seating in the piston bore. If evidence of fluid leakage is noted, the caliper should be rebuilt.
Do not use abrasives on the bolts in order not to destroy their protective plating. You should not use compressed air to clean the inside of the caliper, as it may unseat the dust boot seal.
  1. If not already in place, attach the support spring to the inboard brake pad.
  2. Install the anti-rattle clip on the trailing end of the inboard pad's anchor plate. The split end of the clip must face away from the rotor.
  3. Install the inboard pad in the caliper. The pad must lay flat against the piston.
  4. Install the outboard pad in the caliper while holding the anti-rattle clip.
  5. With the pads installed, position the caliper over the rotor.
Before securing the caliper, ensure the brake hose is not twisted, kinked or touching any chassis parts.
  1. Lubricate the caliper pins and bushings with silicone grease. Line up the mounting holes in the caliper and the support bracket and insert the mounting bolts. Make sure that the bolts pass under the retaining ears on the inboard shoes. Push the bolts through until they engage the holes of the outboard pad and caliper ears. Thread the bolts into the support bracket and tighten them to 7-15 ft. lbs. (9-20 Nm).
CAUTION On models with manual/power brakes, pump the pedal until the caliper pistons and brake shoes are seated. On models with anti-lock brakes, turn the ignition ON and allow the booster pump to build pressure. Pump the brake pedal until the shoes are seated and the indicator lights turn off.
  1. Fill the master cylinder with brake fluid and pump the brake pedal to seat the pads.
  2. Install the wheel assembly and lower the vehicle. Check the level of the brake fluid in the master cylinder and fill as necessary.

Remember to rate this, good luck.

Nov 04, 2010 | 1994 Jeep Grand Cherokee

1 Answer

How to replace anti-rattle clips in a 2002 chevy blazer. I went to replace my brake pads on the front and forgot to put clips in. this is my first time changing pads.


You'll need to take out the pads agaon and clip the anti rattle plates to the back of the pads and then reassemble, the same way you did before....Don't open the brake lines or nipples just push the pistons into the cylinders with a convenient lever, so you have room for the new items to fit....Once fitted remeber to pump up the brakes before you start or move the vehicle....Regards Johngee

Oct 07, 2010 | 2002 Chevrolet Blazer

1 Answer

How to change front brake pads on 2003 Chevy Suburban


Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket 93086g95.gif

  1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
  2. Raise and support the vehicle safely.
  3. Remove the wheel and tire assembly.
  4. Compress the brake piston back into its bore using a C-clamp.
  5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
  6. Remove the inboard and outboard pad.
  7. Remove and discard the anti-rattle clips.
To Install:
Caliper bracket sleeves 93086g97.gif

  1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
  2. Install new anti-rattle clips.
  3. Position the inboard and outboard pads into the support bracket
  4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
  6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
  7. Install the tire and wheel assembly. Lower the vehicle.
  8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
  9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.
Rear To Remove:
  1. Remove 2/3 of the brake fluid from the master cylinder.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
  5. Remove the brake pads from the caliper mounting bracket.
  6. Remove and discard the anti-rattle clips.
Rear brake caliper 93086g96.gif

To Install:
  1. Install new anti-rattle clips.
  2. Position the brake pads to the caliper mounting bracket.
  3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
  5. Install the wheel and tire assembly.
  6. Lower the vehicle.
  7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.
prev.gif next.gif

Jul 05, 2010 | 2004 Chevrolet Suburban

1 Answer

I have a 2002 Lincoln ls . How do I replace the abs speed sensor? Right front tire?


you have one on the inside of each wheel.
SECTION 206-09A: Anti-Lock Control 2002 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Front Wheel Speed Sensor
Material Item Specification RTV Silicone Sealant
FSTZ-19G204-AB (Canada CXC-114A) NAVSTR Sealer
Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Position the inner splash shield aside.
    1. Remove the pin-type retainers.
    1. Position the inner splash shield aside.
  1. Disconnect the anti-lock brake sensor electrical connector.
  1. Remove the anti-lock brake sensor harness from the brake hose clips.
  1. Remove the anti-lock brake sensor.
    1. Remove the anti-lock brake sensor clip.
    1. Remove the anti-lock brake sensor.
  1. NOTE: Make sure the anti-lock brake sensor is fully seated before installation of the new clip.
    To install, reverse the removal procedure.
    • Apply a 2.5 mm (0.1 in) bead of silicone sealant to the outside diameter of the anti-lock brake sensor.
-------------------------------------------------------------------------
Rear Wheel Speed Sensor Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Disconnect the rear anti-lock brake sensor electrical connector.
  1. Remove the rear anti-lock brake sensor harness from the control arm clips.
  1. NOTE: Clean off dirt and foreign material that may have collected around the rear anti-lock brake sensor before removal.
    Remove the rear anti-lock brake sensor.
    1. Remove the anti-lock brake sensor bolt.
    1. Remove the anti-lock brake sensor.
  1. To install, reverse the removal procedure.

Feb 24, 2010 | 2001 Lincoln LS

Not finding what you are looking for?
2002 Chevrolet Malibu Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...