Question about 2000 Chrysler Town & Country

1 Answer

Brake lights not working

I have a 2000 Chrysler T&C brake lights(both) not working including the 3rd Center one when brakes are pressed.
Fuses are good.
Any Ideas?

Posted by on

  • rshaff Jan 13, 2009

    thanks i will try to trouble shoot that



  • rshaff Jan 14, 2009

    Bought a new switch and replaced it after trouble shooting it. Switch cost 12.99. Thanks that fixed my problem

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

BRAKE LIGHT SWITCH LOCATED ABOVE THE BRAKE PEDAL

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tail lights aren't working on my 2000 sebring . I have checked all fuses, but had to remove the horn fuse because alarm kept going off .


When you say tailings do you mean all the lights on the back including brake/turn signals or do you mean parking lights which includes the front parking lights? People use the term tailings for either one.

Jul 08, 2016 | 2000 Chrysler Sebring

1 Answer

Why are there no brake lights or high-level stop light?


Suspect failure of the brake light switch attached to the brake pedal inside

Jan 05, 2016 | 2000 Honda Civic

1 Answer

1998 chrysler town &country brake lights dont work but the 3rd one does


do your dash lights go out too? .. corroded wires (you can do an insulation breakdown test), or its grounding out in the console, but that would most likely blow the fuse. check to make sure u r looking at the right fuse too, wires can be connected to other random components, for example you may find your horn doesnt work either. and being as you have 3 brake lights, it may be possible they are on 2 diff fuses

hope this helps some!

Feb 23, 2012 | 1998 Chrysler Town & Country

1 Answer

Does the brake switch also operate the high mount brake light


Hi,
Get the original bulb for that 3rd brake light from the dealer parts center.
Tell them( parts dealer center ) the model of your vehicle and they will provide necessary part.

Hope that helps!

Nov 30, 2011 | Dodge Cars & Trucks

1 Answer

My brake lights wont work at all light bulbs has been replaced and fuses been checked its a 1996 chrysler town & country


Brake light switch can be checked with a test light. Since the 3rd brake light is not working That's probably the problem.

Feb 15, 2011 | 1996 Chrysler Town & Country

1 Answer

I recently replaced the front rotors, brake pads and master cylinder in my 2003 Durango. I've since discovered that the brake lights are not working, including the 3rd brake light in the tailgate. I...


Hello, Well there is not much more it could be unless you have a shorted wire or a burned fuse. I would normally think that the turn signal canceler was bad but the 3rd brake light will still work if that is bad so I would check all fuses and for bare or shorted wires.

Jan 18, 2011 | 2003 Dodge Durango

2 Answers

Bottom brake lights and hazard lights do not come on. All other lights work including top brake lights. Fuses and bulbs checked.


Check for power out of brake light switch by brake pedal. Of its faulty , the 3rd brake light will still work. Hope this helps

May 20, 2009 | 2000 GMC Yukon Denali

1 Answer

Chrysler Voyager 2000 no brake lights


The voyagers have a little circuit board connected to brake wiring that have high failing rates. I am not exactly sure about the 2000s but most the newer ones have these. Some of the older ones have a relay behind the trim that tend to short out. You can use an ohmmeter to test any current/voltage to wiring and sockets as well as circuits and relays.

May 19, 2009 | 2000 Chrysler Grand Voyager

1 Answer

Brake lights


do you have a 3rd brake light like on that is on the roof or in the rear window? if so does it work?
the brake lights are usually a 2way bulb so just because the lights work doesn't mean that brake lights will. if the 3rd brake light works replace the brake light bulbs if none of them work including your 3 brake light. check into having your brake switch changed. that is the switch under the brake pedal. when it is pressed the brake lights come on and when released they go off. if the bulbs do not fix the problem than try the switch.

Jul 19, 2008 | 1987 Honda Accord

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...