Question about Cars & Trucks

Open Question

Freelander 2 clutch pedal doesn't come back fully

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: rover freelander

I have the same problem. Your clutch booster kit is broken and needs to be replaced. It is that cylindrical hydraulic component next to the engine. Even if just a small part in this thing is jammed you have to replace the whole thing. Well, that's what the guys from land rover told me anyway. Good luck.

Posted on Sep 17, 2008

TLRogue
  • 99 Answers

SOURCE: hard clutch pedal

You cannot bleed a servo. it runs using the vacuum from either inlet manifold, or a seperate vac pump.Ensure pump is working if fitted (end of camshaft) the pipes to the servo are not leaking by removing the pipe from servo and start veh. If there is good suction then its servo failure. hard pedals can also be caused by pressure plate fatigue in the clutch itself.

Posted on Jan 21, 2009

  • 19 Answers

SOURCE: Clutch Pedal not returning 3000GT

Buy a seal kit from autozoe, wil cost you around 17 dollars. Remove clutch aster cylinder by firstly undoing the resevoir clamp and remove the reservoir to give you access to the hard hydraulic line and detach the line. Undo the two bolts holding the master cylinder to the firewall and then go inside the car and pull the cotter pin holding the end of the mastrecylinder plunger to the pedal (watch the washers and remember how they go back on). Remove the unit, and strip it down to replace the plunger and releif valve you get from the kit. Good Luck.

Posted on Jul 17, 2009

  • 60 Answers

SOURCE: 96 pathfinder clutch pedal has lost pressure,

usually when this happen you lost fluid pressure look for a fluid leak at the clutch master cylinder under the hood ,it should be by the brake master ,it has a small plastic tank on top with a black rubber cap or underneath on the transmission there is the clutch slave cylinder it will have a small 2 inch rod that pushes the clutch fork ,look for the rubber boot on it ,see if there is fluid coming out of it ,also follow the clutch fluid lines maybe somthing has damaged one and its leaking !

Posted on Aug 08, 2009

  • 236 Answers

SOURCE: I have a 2002 freelander

Sounds like a clutch control problem. Did you check the fluid in the clutch master? If you get a leak and run out of fluid this will also do this. This vehicle uses DOT 4 brake fluid in the master.

Posted on Jun 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch pedal return too high


Freelander 1.8 clutch pedal height is set by the master cyl piston ram.
Circlip has broken or come lose allowing the piston to come out more.
FIX This is a sealed system. Cost from about £45.for system. Can be changed easly at the roadside 30 min no special tools needed

Apr 01, 2014 | 2002 Land Rover Freelander

1 Answer

How do I fill up the clutch fluid resevoir?


If your clutch pedal doesn't quite have the pressure it used to, or your clutch fluid just looks old and dirty, it may be time to bleed and/or replace the clutch fluid.
Items needed:

8mm open or box end wrench
Clear tube (1/4" ID)
One bottle DOT3/DOT4 brake fluid (doesn't have to be full)
A friend to press the clutch pedal for you

Locate the bleeder valve on the clutch slave cylinder.

qk2cpkiyfjgaaaaasuvork5cyii=Use your 8mm wrench to open the valve one full turn, don't remove it.

Stick your hose over the bleeder valve and have it drop off into a container.
lpd+ipdyjdaaaaaasuvork5cyii=Be sure to check the clutch fluid level before bleeding the system, you don't want to let it get below the MIN line.

Have your friend pump the clutch pedal to start removing the fluid. Don't be con if they tell you the pedal went down to floor and won't come back up on it's own, that's normal. They'll just have to wedge it back up with their foot.

NOTE: When bleeding the system, make sure the cap is ON or you will just be sucking in air

Refill the clutch fluid as necessary to keep it above the MIN line. Since the clutch fluid reservoir is very small you'll have to keep a close eye on it.
zepo2bz1de6vgaaaabjru5erkjggg==I just had some extra ATE brake fluid left over from my brake fluid change so I decided to just use it since it is a DOT3/DOT4 fluid. But high performance fluids are not necessary for the clutch fluid so you can just use regular cheap DOT3 or DOT4 fluid and it won't make a difference.

When you see the fluid in the hose change completely from the old color to the new color then you know the system has been flushed and is now full of new clutch fluid. Have your friend do one l press of the clutch pedal and tighten the bleeder valve once the pedal hits the floor. Since you can't use a torque wrench on the bleeder valve, it's important to note it does not need to be very tight so don't try overtightening it and just snug it up with your wrench.

Pump the clutch pedal again and the pressure should return. And that's all, you're finished.

this video tutorial can help you.
http://www.youtube.com/watch?v=a-XhFxlkzFI&feature=player_detailpage

Jun 12, 2012 | Cars & Trucks

1 Answer

Hey, i'm looking to buy a used 2003 volkswagon passat gls 2.8 v6 manuel, the clutch doesn't engage befor it's almost all the way out,i told the dealer but he says that the clutch is fine...


here's what you can do to fix your clutch.

1. if your clutch still uses clutch cable (there is a cable between the transmision and the clutch pedal), the you can adjust the clutch release by tightening/loosen the clutch pedal. adjustments can be done on the transmission side of the clutch cable.
2. hydrovac clutch with self correcting feature. just pull your clutch pedal for a few seconds and check if the clutch release changes.
3. hydrovac clutch without self correcting. between the clutch pedal and the clutch master, you can see a piece of metal rod that connects the 2. this metal is called push rod. there are screws/nuts at the clutch pedal to adjust this push rod. just adjust this screw to your prefered clutch release.

Aug 10, 2011 | 2001 Volkswagen Golf

1 Answer

Clutch pedal goes strait to the floor??clutch won't bleed up??


It has air bubbles on the piping, fill the deposit with brake solution, and push and pull the clutch pedal with your hand it doesn't matter if it goes straight to the floor if that happens pull it with your hand, repeat that as if you are bleeding it up, then disconnect the piping beneath the car, the air bubbles will be forced out, then reconnect the piping and repeat the procedure, push and pull the clutch pedal like a 100 times, then disconnect the piping and reconnect. The clutch pedal should be able to go back when there is no air on the piping. If that doesn't work, replace your clutch pump

Jun 23, 2011 | Honda CR-V Cars & Trucks

1 Answer

Have freelander td4 03 plate, continuous problem with clutch. had new clutch , slave cylinder and master 2 months ago, all fine till a month ago lost pedal completely , had new master fittted problem fixed...


Definitely a hydraulic issue. Iknow you said they were both changed, but its usually the master & slave assembly that go faulty on the Freelander. Both parts come filled with fluid and pre-bled and only require fitting, no bleeding. Check with garage to make sure they did not split / bleed them.

Jun 06, 2011 | 2003 Land Rover Freelander

2 Answers

I have a 2002 freelander TD4 and we think the clutch has gone when u push the clutch pedal down it just stays there and wont come back up does this sound like the clutch has gone?


Sounds like a clutch control problem. Did you check the fluid in the clutch master? If you get a leak and run out of fluid this will also do this. This vehicle uses DOT 4 brake fluid in the master.

Jun 06, 2011 | 2002 Land Rover Freelander

1 Answer

No pressure on clutch pedal car will go into gear and drive pedal wontcome back up


U have a failed hydraulic clutch master or slave cylinder, it is best to replace the pair.

Jan 18, 2010 | 2002 Land Rover Freelander

2 Answers

Pushing clutch pedal fully down &still difficult to obtain gears


Clutch plate is worn down to nothing and/or throwout bearing needs replaced.

Jul 29, 2009 | 2002 Land Rover Freelander

1 Answer

Probable clutch needed


If you put your car in 1'st gear, release the clutch pedal and nothing happens, absolutely the clutch is faulty.
Cheers

Feb 15, 2009 | 2002 Land Rover Freelander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...