Question about Dodge Grand Caravan

Open Question

Bleed air off of a 2009 dodge caravan coolant system

Just need to know where the bleeder screw is on the coolant system of my 09 dodge Gr Caravan Flex fuel

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 548 Answers

SOURCE: replace broken fuel door 2000 dodge caravan

If you're on the smallish side and pretty limber, you might avoid removing the rear wheel. If not, you will likely need to remove the rear wheel and put the van on jack stands securely. I would remove the underside splash shield and gain access from underneath. It looks like you will need to unscrew the plastic insert that surrounds the filler neck inside the area that is exposed when you open the fuel door. Make sure you get the vent hooked up correctly when you are done.

Posted on Jan 31, 2009

Ad
  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

  • 57 Answers

SOURCE: 2000 Dodge Grand Caravan need to know where relay

the cooling fan relay is not in the fuse box.

it is a solid state relay bolted to the radiator core support just behind the bumper

Posted on Jun 16, 2009

66 chrgr
  • 1011 Answers

SOURCE: need to know where connection for EGR valve 05 dodge gr caravan

by the alternator plugged into the egr valve.

Posted on Jun 16, 2009

  • 5 Answers

SOURCE: Is a 2000 Dodge Grand Caravan fuel filler neck usable in a 1999?

yes it will swap and you have to remove it from the bottom of the van remove the screw/clips from inside the filler door and then from underneth disconect the filler tube ti tank and the vent hose to the tank i belive there is a bracket also holding the filler tube to the body with one bolt then it snakes out of the va r insalating is just reverse

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed brakes on a 2008 dodge caravan


first you need to make sure you can open all bleeders on each wheel.You will need 2 people,1 to open and close bleeder and 1 to pump and hold pedal down.Be carefull,bleeders that haavnt been opened in a while can break off.Spray them with PB Blaster and let them sit for while.Then you start with pass rear then drivers rear then pass front then drivers font in that order.Make sure master is full of fluid,then have person pump brakes 5 to 7 times and hold them on,then open bleeder until the pedal is down to floor.Make sure person pushing pedal lets you close the bleeder before letting pedal up to pump it again.Repeat this until there is no air coming out of bleeder.If they let pedal up and you havnt closed the bleeder, it will **** air back into system.

Nov 13, 2012 | 2008 Dodge Grand Caravan

1 Answer

2002 caravan replaced radiator , now we have no heat how do you bleed the air out of the system.


Pull the radiator/ resevoir cap off. start the car and let warm up. after it is warm rev the engine and add coolant as needed. only add alittle at a time. revving the engine pushes the air thru. you will loose some coolant as the air is purged. do this until you get heat from the dash. then keep check on the coolant level for a few days.

Jan 22, 2011 | 2002 Dodge Caravan

1 Answer

Changing a thermastat on a 2003 Caravan


the 1993 caravan had two engines offered a 2.5L 4cylinder and a 3.3L v6........on the 2.5L the thermostat is located on the front of the cylinder head were the top radiator hose attach's.
remove the top hose were it attach's to the thermostat housing and the remove the thermostat housing and lift out the thermostat and replace with the new one making sure the spring on the thermostat is facing the engine replace the thermostat housing and top radiator hose and remove the bleeder screw from the top of the thermostat housing and fill radiator with new antifreeze. when you see antifreeze coming out the bleeder hole replace the bleeder screw.

The 3.3L v6 also has the thermostat at the front of the cylinder head were the top radiator hose attach's the thermostat housing the procher is the same except for bleeding the radiator, to bleed the cooling system remove the coolant temp. sensor it is located just below the thermostat housing and fill radiator with new antifreeze until the antifreeze starts coming out the coolent tempt sensor hole them reinstall the sensor and top of radiator.........GOOD LUCK

Dec 09, 2010 | 2003 Dodge Caravan

2 Answers

I have a 2002 caravan.i replaced the left rear flex hose and now the brake pedal continues to sink to the floor


Try to bleed your brakes again or you may need to look at the Master Cylinder, it could be bad.

Jun 25, 2010 | 2002 Dodge Caravan

1 Answer

I replaced the thermostat and the coolant does not seem to get to the engine at al now. What is wrong?


There should be an air bleeder on top of the thermostat housing. Make sure you bleed all of the air out of the coolant sysytem before running it or you may have an air pocket in a cylinder head and cause more problems. Never open a radiator while the engine is hot.

Apr 28, 2010 | 2000 Dodge Grand Caravan

1 Answer

I change the pads on my dodge jorney and


this is very simple but you will need an assistant. take the wheel off of the caliper you need to bleed. have your assitant keep steady pressure on the brakes while you slowly open the bleeder screw. you don't want to open it so far the brake fluid squirts all over. if the brake pedal hits the floor you will need to tighten the bleeder screw before your assistant lets off the pedal. another helpful thing to have is a clear tube that fits snugly aroung the bleeder screw so when you open it you can see the air bubbles more easily.

Apr 04, 2010 | 2009 Dodge Journey

1 Answer

Brakes sticking on


did u bleed the brake system?? if not that could be your problem,even if u just pushed the pistons back without opening the bleeders ..air can still be introduced into the system

Sep 05, 2009 | 2003 Dodge Caravan

1 Answer

I repaired the break lines now i need to bleed them


Bleeding brakes is two person operation. Check to see where bleeder valve is on calipers, usually on back side. Should be 3/8". They are hopefully covered with rubber boots or caps. If not then I would spray them with breakaway to assist in loosening. These are easily snapped off if they are frozen so be careful. Person in car, ENGINE OFF, pumps brake pedal until it becomes hard and holds it there. Person bleeding brakes turns bleeder valve to open just a crack, at first air will escape and some fluid. Person pressing pedal down will tell you pedal is down all the way. At this point tighten bleeder valve. Now repeat operation until you have fluid only coming from bleeder valve. Be careful as the fluid will shoot out of bleeder and hit you right in the face, safety glasses are recommended. Be sure to top off brake fluid reservoir before, during and after this operation. Test drive short distance to see if all air is evacuated from system, you'll know if there is air still in system if you have a soft pedal, if so repeat once more.

Jun 22, 2009 | 2000 Dodge Caravan

1 Answer

Can't find port to bleed front brakes 1995 Dodge Caravan


should be a bleeder screw on each caliper, unless, they were broken off in a previous attempt? They have to be there

Apr 07, 2009 | 1995 Dodge Caravan

2 Answers

Overheating


Did you bleed the cooling system after refilling the radiator ? to bleed the system, fill the radiator with water and coolant. Run the engine until it is at a good temperature. Then turn off the engine and look for a bleeding screw at the oulet of the thermostat housing and turn it with a screwdriver counterclock wise. The trapped air will go out and coolant will start coming out. refill the radiator and repeat until only coolant comes out and no air.be careful not to burn yourself.

Feb 16, 2009 | 1994 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...