Question about 2005 Chevrolet Cobalt

Open Question

How To Replace Heater core Chevy Cobalt 05-10

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 231 Answers

SOURCE: Heater Core

1) disconnectnegative battery cable
2) remove coolant reservoir
3) dis-connect heater hoses from heater core and plug holes in heater core, some coolant will drain out
4) remove mounting bolts and nuts on fire wall
5) remove glove box liner and door
6) lable and dis-connectheater controls
7) dis-connectand remove computer and mounting bracket
8) move radio antenna wire
9) remove kick pannel and un-bolt lower corner of dash
10) remove screws and nuts holding the housing inside the cab
11)remove the heater housing from the vehicle
12) detatch the core retaining straps and remove the heater core
13) installation is this procedure in reverse
I hope that this fixes your problem good luck and please take the time to rate this response.

Posted on Oct 17, 2008

Shouldibuyit
  • 44 Answers

SOURCE: replace heater core 1994 chevy g20 conversion van

Here a are the instuctions to remove it. I did not know if you have A/C or not so I included both for you.

REMOVAL & INSTALLATION
Without Air Conditioning
ALL MODELS
See Figure 1

  1. Disconnect the negative battery cable.
  2. Remove the coolant recovery bottle.
  3. Place a pan under the van and disconnect the heater intake and outlet hoses. Quickly remove and plug the hoses and support them in an upright position. Drain the coolant from the heater core into the pan.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw. Remove the duct.
  2. Remove the engine cover.
  3. Remove all the instrument panel attaching screws.
  4. Carefully lower the steering column. Raise and support the right side of the instrument panel. Refer to for further details.
  5. Remove the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  6. Disconnect the temperature door cable. Carefully fold the cable back and out of the way.
  7. Remove the three nuts from the engine compartment side of the distributor case and the screw from the passenger compartment side.
  8. Remove the heater case and core assembly.
  9. Remove the core retaining straps and remove the core.
To install:
  1. Install the core.
  2. Install the core retaining straps.
  3. Install the heater case and core assembly.
  4. Fasten the three nuts on the engine compartment side of the distributor case and the screw on the passenger compartment side.
  5. Connect the temperature door cable.
  6. Install the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  7. Install the steering column.
  8. Fasten all the instrument panel attaching screws.
  9. Install the engine cover.
  10. Install the duct. Install the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw.
  11. Connect the heater intake and outlet hoses.
  12. Fill the cooling system.
  13. Install the coolant recovery bottle.
  14. Connect the negative battery cable.
1990-95 MODELS With A/C

  1. Disconnect the battery ground cable.
  2. Remove the engine cover.
  3. Remove the steering column-to-instrument panel bolts. Lower the column carefully.
  4. Remove the upper and lower instrument panel attaching screws. Remove the radio support bracket screw.
  5. Raise and support the right side of the instrument panel.
  6. Remove the lower right instrument panel bracket.
  7. Remove the vacuum actuator from the kick panel.
  8. Disconnect the temperature cable and vacuum hoses at the case. Remove the heater distributor duct from over the engine hump.
  9. Remove the two defroster duct-to-firewall attaching screws below the windshield.
  10. Under the hood, disconnect and plug the heater hoses at the firewall.
  11. Remove the three nuts and one screw (inside) holding the heater case to the firewall.
  12. Remove the case from the van. Remove the gasket for access to the screws holding the case together. Remove the temperature cable support bracket. Remove the screws and separate the case. Remove the heater core.
To install:
  1. Install the heater core.
  2. Assemble the case and fasten the screws.
  3. Install the temperature cable support bracket.
  4. Position the gasket, then install the case in the van.
  5. Fasten the three nuts and one screw (inside) holding the heater case to the firewall.
  6. Connect and plug the heater hoses at the firewall.
  7. Fasten the two defroster duct-to-firewall attaching screws below the windshield.
  8. Install the heater distributor duct.
  9. Connect the temperature cable and vacuum hoses at the case.
  10. Install the vacuum actuator at the kick panel.
  11. Install the lower right instrument panel bracket.
  12. Fasten the radio support bracket screw.
  13. Fasten the upper and lower instrument panel attaching screws.
  14. Fasten the steering column-to-instrument panel bolts.
  15. Install the engine cover.
  16. Connect the battery ground cable.
  17. Refill the cooling system as necessary.

Posted on Nov 28, 2008

boscia
  • 163 Answers

SOURCE: replace a heater core in 2000 chevy blazer

it is located under the dashboard against the firewall of the passenger seat. i recomend buying a repair manual from your local auto parts store before attempting as it requires draining, flushing, refilling and bleeding the cooling system as well as removing many other componets like the entire dashboard and thermostat

Posted on Dec 01, 2008

  • 289 Answers

SOURCE: How to replace a heater core in a 1994 chevy 1500

As with all vehicles it seems the first part that they build around is the heater core. It is under the dash above the floor housed in a black plastic sealed box. Sealed with goop. Locate that box and start removing everything around it that is peventing taking the cover off. Of course disconnect the heater hoses under the hood a thefirewall.

Warning it is never as easy as it sounds.

Posted on Nov 29, 2009

Jim1969pa3
  • 152 Answers

SOURCE: I have a 1999 chevy silverado and I need to change heater core

Not a whole lot different. Just need to keep removing plastic down at the heater until you get to the heater core. Then disconnect it on the firewall side.

Posted on Dec 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Manual 2006 chevy cobolt heater core


any good mechanic can change the heater core .

Mar 20, 2015 | 2006 Chevrolet Chevrolet Cobalt LS

1 Answer

How to install Block heater 2007 Chev Cobalt LS?


I think you can buy a dipstick heater to keep the oil warm, or a coolant heater. Some replace a freeze plug (difficult to install) and some go into the radiator hose i think. Check with a parts store.

Jan 13, 2015 | Cars & Trucks

1 Answer

Can hear water when running.


can be clogged heater core,try inspecting the heater core.

HEATER CORE REPLACEMENT


If its clogged it can be cleared with the use of Garden hose p[ump.The water has to be turn into the heater hose line and then water has to be removed out via the pump.

==========

For complete step by step procedure,refer heater core flushing and other help links mentioned below.


======

Click the link below:-----

------------

How to Flush Heater Core?

http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html

------------

How to replace heater core on Chevy Astro?

http://schematicsdiagram.blogspot.in/2012/03/how-to-replace-heater-core-on-chevy.html

-----------

Replacing heater core for grand marque?

http://schematicsdiagram.blogspot.in/2012/03/replacing-heater-core-for-grand-marque.html

------------

How to replace heater core for All car models?

Click the link below:---

http://technoanswers.blogspot.com/2011/11/how-to-replace-heater-core-for-all-car.html

-------------

How to replace heater core on Buick Regal?

http://howtobyme.blogspot.in/2012/02/how-to-replace-heater-core-on-buick.html

-------------

How to Remove Heater Core on 2008 Honda Odyssey?

http://howtobyme.blogspot.com/2011/12/how-to-remove-heater-core-on-2008-honda.html

------------

Honda Heater Core Replacement?

http://howtobyme.blogspot.com/2011/12/honda-heater-core-replacement.html

------------

How to replace heater core on Mitsubishi magna?

http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on.html

-----------

How to replace heater core on Mitsubishi eclipse?

http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on_10.html

=========

These will help.

Thanks.

Nov 28, 2012 | 2000 GMC Jimmy

2 Answers

How do you clear a clogged heater core?


Charles,when they get clogged,you must replace,need help doing that,if so then we need the year,make ,model and engine size.

Nov 27, 2012 | 1999 Ford Escort

1 Answer

Hearing water noises behind dash in 2009 Chevy cobalt


your heater core is behind the dash on the passenger side. The antifreeze travels through it as its cycle through the engine. Thats what gives you hot air when you turn your heater on. If you find that there is water dripping or pooling in the floor board of the passenger side then your heater core needs to be replaced and its not an easy task.

Aug 18, 2012 | Chevrolet Cobalt Cars & Trucks

1 Answer

Will thermagasket work for my 2006 chevy cobalt 2.2 liter?i discivered coolant in 2&3 clyclinders have car misfiring on start up


It can be used as a temporary fix but the head gasket is going to need to be replaced. You also run the risk of pluging up more than just the leaking head like Heater core, Radiator. If you use the Thermagasket make it a short use and flush the cooling system after proper repair has been made

Mar 01, 2010 | 2006 Chevrolet Cobalt

2 Answers

How to replace a heater core in a 1994 chevy 1500


As with all vehicles it seems the first part that they build around is the heater core. It is under the dash above the floor housed in a black plastic sealed box. Sealed with goop. Locate that box and start removing everything around it that is peventing taking the cover off. Of course disconnect the heater hoses under the hood a thefirewall.

Warning it is never as easy as it sounds.

Nov 29, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
2005 Chevrolet Cobalt Logo

Related Topics:

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...