Question about Jeep Liberty

Open Question

Location of 2011 jeep liberty blend door actuator

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MNfisherman
  • 11896 Answers

SOURCE: A/C blend door actuator,2001Cadillac Deville

THe actuator is usually in the vent housing behind the control panel. You can follow the vacuum lines from the a/c-heater control to the actuator.

Posted on Jun 30, 2009

warlock61
  • 659 Answers

SOURCE: need to locate blend door actuator 98 lincoln

it is located on top of the heater box assy behind the dash just to the left of of the glovebox if you open the glovebox and look to the left you can see it

Posted on Jul 11, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

  • 2 Answers

SOURCE: How do you change a blend door actuator on a 2003

Not sure why previous poster showed you how to fix a switch in the door, but anyways.....
I had same problem as you.

My Yukon has the single overhead door, not the "barn-doors", hopefully yours is the same. Open rear cargo door. Using a trim tool (buy the set from Harbor Frieght for less than $10) remove the lower trim (at carpet), upper trim (at headliner), then the right pillar trim (mine has small Bose speaker in it). Loosen trim between passenger side back door and the cargo area main right rear trim. Remove main cargo area right main panel, by unscrewing the big black know, prying out the small plastic plug, and carefully disconnecting the AUX power plug (looks like a cig lighter outlet) once you can get behind the panel a little bit.

Now you are looking at the entire rear system. There are 2 of these actuators. The front one controls airflow going either to floor or ceiling vents, the rear one (towards middle of entire unit) controls AC vs heat percentage flowing through the ducts. Unplug the connector, and 3 screws to remove it.

Install is the reverse.

Posted on Mar 14, 2010

  • 248 Answers

SOURCE: What do I have to remove to access blend door actuator

very lenghty process. too long to describe here....go to Bonneville Forums read the text and follow linked there at the bottom....very good and detailed....I'm doing that right now,,,,it is a bugger,

Posted on Apr 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Jeep Liberty and the heater only blows like warm air. I have replaced the thermostat and flushed the heater core and still no change. What could be wrong?


Blend door may be sticking thus mixing too much cold air with the hot. Bad blend door actuator, vacuum leak or blend door seal is bad.

Feb 19, 2015 | Jeep Cars & Trucks

1 Answer

Why does my 2010 Jeep Liberty just blows cold air?


Blend door is not moving to open to the heater core. Coud be that the cable is not connected to the dash lever but if it's vacuum actuated the vacuum line could be off. Check that your getting vacuum.

Dec 01, 2014 | 2010 Jeep Liberty

1 Answer

Jeep liberty heater


if there is not even luke warm air coming from the heater it may be caused by the blend air door motor. on some of the jeeps they came out with a new upper heater housing that was a new design. I believe if your vehicle had this update the dealer would be able to check TSB's for the cause. other wise like I said, most likely the blend air door and/or motor

Mar 21, 2014 | 2011 Jeep Liberty

1 Answer

Air Condtioner Partially Working Jeep Liberty 2010


Usually a sign of a stuck blend door under the dash.
Could be a faulty blend door actuator, or the main controller.
You may need a shop manual to make the repairs since this is generally beyond the abilities of a DIY repair book.

Jul 16, 2013 | 2010 Jeep Liberty

1 Answer

2005 jeep liberty sport manual


The blend door actuator will not be the problem, the blend door will be stuck or broken, common problem.

Jul 27, 2012 | Jeep Liberty Cars & Trucks

1 Answer

Air blend door jeep liberty 2010


My blend air door is stuck on my 2010 liberty. I have removed the actuator panel on the drivers side and the middle door that controls the air flow to the dash is completely seized. There are 4 blend air doors on this liberty, 2 control the heat/ac and 2 control the air flow.
there is no access to them from the drivers side and the passanger side looks like I have to cut into the air box to get to them.

Jan 03, 2012 | 2010 Jeep Liberty

2 Answers

I have a 2002 Jeep Liberty Limited, 3.7 L motor. The heater will not blow hot air. The A/C and fan work well. When I turn the temperature dial to hot, there is only cold air coming out. Can you assist me?


Jeeps are notorious for having broken temperature control (Blend Air) doors. A malfunctioning Blend Air Door actuator probably caused it to break. The dash will have to be removed to replacethe door and the door actuator.

Jan 16, 2011 | 2002 Jeep Liberty

1 Answer

Blows cold air in heat mode


Sounds like the heater control valve/ blend door. The actuator may be stuck or broken. The actuator opens and closes to adjust for the heat setting in the car. You might be able to take a coathanger and manually open the door if you can get to the control arm. They are usually hard to get to and pretty expensive. It is located under the dash at the heater core box. Good luck.

Dec 16, 2010 | 2006 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...