Question about 2003 Pontiac Montana

Open Question

2003 Pontiac Montana sliding door contact spring plunger needs to be replaced

I need a part number for a sliding door contact connector, it is a 7 pin plunger

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 55 Answers

SOURCE: replace thermostat 2003 pontiac montana

yes but with the right shaped wrenches and tiny hands it can be done without removing the exhaust crossover pipe

Posted on Oct 16, 2008

  • 7 Answers

SOURCE: 2005 Pontiac SV6 Montana key fob unlocks doors but will not lock

For the sliding doors you need to clean the contacts, there are 6 or 8 on both sides, just wipe them clean as they are probably covered in oil/grease/grime.

Posted on Feb 14, 2009

  • 98 Answers

SOURCE: My 1999 pontiac montana rear sliding power door will not work

I went to bulldogsecurity.com and looked up the wiring diagram for this vehcle. However, prior to checking this part, I would check to see if you have a blown fuse. It doesn't hurt and only takes a few minutes. There should be a fuse for that either somewhere on the side of the dash or near the brake pedal area. If not it may be under the hood, but it should be inside the vehicle. You may have multiple fuse boxes. If it has (2) sliding doors it will have a wire for the auto doors in each kick panel (under the plastic trim/molding) when you open the door and look down you will see all of the trim/molding it should snap out or may be held in place with a screw or (2). Once you remove that you should see the wires. It says for the left side it is either light blue or black and the right side is definitely light blue. Trace this wire until you find out where it ends (the motor or switch to control the auto doors) Then test the switch/motor to see if it is bad.

Posted on Mar 02, 2009

landsend
  • 1066 Answers

SOURCE: need to replace thermostat on pontiac montana van.

public library...Chilton or Haynes auto repair manuals or collisionrepairadvice.com     make sure you bleed the system

Posted on Apr 03, 2009

daves944
  • 1050 Answers

SOURCE: 2003 Pontiac Montana Front Wheel Bearings

Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Automatic side door wont work automatic


Check the electrical spring connectors at the door, and the contacts at the door pillar. They are notorious for corrosion. Take some steel wool or very fine sand paper, rub against the contact areas until a copper color returns. The pillar contacts get corrosion and very poor continuity thru the connector. The spring contacts in the door can also get corrosion on the back side at the connector, try cleaning them on the outside first before attempting to remove door panel.

Apr 09, 2011 | 2001 Pontiac Montana

1 Answer

I cant get the power sliding door alarm to stop dinging.


I have a 2006 SV6 with the power sliding doors. The problem that I found was with the contacts on the door ( They are called plungers) the movable pins were losing connection with the fixed part The plunger is very easy to replace if you can find one. The plungers are covered with a rubber cover and is held in place with 2 plastic pins. My Pontiac dealer could not even find one in his books or even a picture of one, and claimed that he had never had anyone come with a door problem. My Chevy dealer said that it came with a wiring harness that is not needed for $154. The cure that I came up with was to take the plunger block apart (it snaps together)and replace the rusted out springs then solder 3" wires to the end of the plunger pins (they solder easy) to the tabs that go to the plug(pop out the tabs or you will melt the plastic. It took about 45 min. now the doors work like new and will never loose contact again

Mar 21, 2010 | 2005 Pontiac Montana

1 Answer

My '99 Pontiac Montana right sliding door and front door do not open. The windows and clock/sometimes CD player don't work nor does the A/C. Is there a fix? The fuses?


2 common possibilities. The plungers and plunger pads on the door and the door jam are corroded. Clean those off with a fine sandpaper, then put a dab of silicone grease on them. Then do the re-set procedure exactly as the steps indicate. If that does not help, then a possible door position sensor or the door control module is bad. A diagnostic using the on/off switch and the open/close switchon the system may indicate a code for door position problem. The door position sensor is part of the door motor/actuator assembly. The control module can be replaced separately. Info from here.

Nov 11, 2009 | 2000 Pontiac Montana

2 Answers

The door chime on our 2005 Saturn Relay Van continuously goes off when you put it in gear. There are no obstructions but the automatic door switch fails to open the door sometimes and other times the chime...


I have a 2006 SV6 with the power sliding doors. The problem that I found was with the contacts on the door ( They are called plungers) the movable pins were losing connection with the fixed part The plunger is very easy to replace if you can find one. The plungers are covered with a rubber cover and is held in place with 2 plastic pins. My Pontiac dealer could not even find one in his books or even a picture of one, and claimed that he had never had anyone come with a door problem. My Chevy dealer said that it came with a wiring harness that is not needed for $154. The cure that I came up with was to take the plunger block apart (it snaps together)and replace the rusted out springs then solder 3" wires to the end of the plunger pins (they solder easy) to the tabs that go to the plug(pop out the tabs or you will melt the plastic. It took about 45 min. now the doors work like new and will never loose contact again

Oct 06, 2009 | 2005 Saturn Relay

2 Answers

2006 Pontiac montana SV6 power sliding door sensor will not acknowledge door is closed and 'ding ding ding' is now heard in my sleep!!! I've had this to three different Pontiac dealers and nothing seems to...


I have a 2006 SV6 with the power sliding doors. The problem that I found was with the contacts on the door ( They are called plungers) the movable pins were losing connection with the fixed part The plunger is very easy to replace if you can find one. The plungers are covered with a rubber cover and is held in place with 2 plastic pins. My Pontiac dealer could not even find one in his books or even a picture of one, and claimed that he had never had anyone come with a door problem. My Chevy dealer said that it came with a wiring harness that is not needed for $154. The cure that I came up with was to take the plunger block apart (it snaps together)and replace the rusted out springs then solder 3" wires to the end of the plunger pins (they solder easy) to the tabs that go to the plug(pop out the tabs or you will melt the plastic. It took about 45 min. now the doors work like new and will never loose contact again

Sep 25, 2009 | 2006 Pontiac Montana SV6

1 Answer

04 pontiac montana sliding doors no longer work


the sliding doors on montana assuming there power have a electrical harness on the bottom track that break and jam the doors but unlikly both have this problem do the doors lock @ unlock if not check switch at drivers door

May 27, 2009 | 2003 Pontiac Montana

1 Answer

1999 Pontiac Montana passenger sliding door stopped working.


Verify the wiring harness which passes under plastic step & carpet at front passenger side. This wiring harness goes from the firewall to the pillar on the right side and some have crimped connectors in them to act as junction between two or more wires (ususlly the 12volt feed), which deteriorate with time, especially with Salt & Water. Then the electric sliding door stops working and even driver the electric seat can loose power.

May 17, 2009 | 1999 Pontiac Montana

1 Answer

2005 Pontiac SV6 Montana key fob unlocks doors but will not lock


For the sliding doors you need to clean the contacts, there are 6 or 8 on both sides, just wipe them clean as they are probably covered in oil/grease/grime.

Feb 12, 2009 | 2006 Pontiac Montana SV6

Not finding what you are looking for?
2003 Pontiac Montana Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...