Question about Dodge Avenger

Open Question

Change map light bulb in 2009 dodge avenger

Map lights

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: How do I get the "Change Oil " light to go off after change .

Turn key to the run posistion and pump the gas peadle 3 times under 5 seconds.

Posted on Jul 18, 2009

Ad
  • 2 Answers

SOURCE: 99 dodge ram interior lights wont come on

I had the same problem and could not understand why I THOUGHT I checked all the fuses, but there is a fuse on the drivers side which is covered by a black thing (no idea why). It is listed as IOD or something. If you lift the black thing up and remove the fuse you will notice it is blown. Replace this and all will be well again.

Posted on Oct 11, 2009

techbuster
  • 5081 Answers

SOURCE: Reset oil change for a 2008 dodge aveneger

To reset your maintenance reminder system (even if the light hasn’t come on yet), you’ll need to turn your key to on (but don’t start!) and make sure your odometer is on TRIP A. Then key off. Press and hold the Odometer/Trip button. While holding down on the button, key the ignition to on (Don’t start the engine!) The display panel will count down from “------“ to “-“Continue pressing the button until the Trip A is displayed. After this step, you are done.

Posted on Oct 21, 2009

  • 63 Answers

SOURCE: 2008 Dodge Avenger check engine light

Not sure if this will work for you but worth a shot. I own a 2005 dodge neon. I know the ecu's are different but maybe dodge was smart and made all the cars this way. Insert you key into ignition. Turn key forward until you are at the last position right before the car starts to crank over. Repeat this for a total of three times then on your digital odometer display, you will see a set of numbers displayed. this will be your code for the malfanction(s) that set your check engine light. Like I said, it might not work on your car but give it a shot. If not, rent an obdII scanner and get your codes. Then you know where to start looking to fix your problem.

Posted on Dec 17, 2009

wilsodfarm
  • 986 Answers

SOURCE: how to change head light bulbs on a dodge caliber

Park the Dodge Caliber on a flat paved or concrete surface. Turn the steering wheel all the way to the side opposite the headlight you are replacing. In other words, if you are replacing the left headlight, turn the wheel all the way to the right. Apply the parking brake and release the hood latch.

  • Step 2 Place a wheel chock behind one of the rear tires.
  • Step 3 Open the hood. This is to allow some light to reach down into the engine compartment.
  • Step 4 Raise the front quarter panel of the side you need to replace the headlight on with the floor jack and place the jack stand under the front frame rail on that side.
  • Step 5 Remove the fender well plugs using the plastic plug puller tool. You do not have to remove the entire fender well cover, but the more plugs you remove, the more access it will give you to the headlight assembly.
  • Step 6 Unplug the headlight switch. Make sure you are unplugging the headlight which will be the inboard plug.
  • Step 7 Turn the headlight bezel a quarter turn counterclockwise and extract the bulb and bezel.
  • Step 8 Insert the new headlight into the bezel, being careful not to touch the glass bulb.
  • Step 9 Insert the bezel and headlight into the headlight assembly and turn a quarter turn clockwise to lock it into place.
  • Step 10 Plug the wire connector into the headlight. This would be a good time to get up and go test the light to make sure it's working.
  • Step 11
  • Posted on Dec 28, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How do I change the entire headlight assembly on a 2009 Dodge Avenger?


    lift the hood on the front of the rad you will find a plastic black cover , its held on with push pin fasteners to remove them you need to lift the center bit , use a small screw driver to do this the fastener now lift out there should be 6 to 8 of them now this cover will come off, you will find 4 10mm bolts that hold the light assemble in place take them out gentley remove said light , the bulb comes out with a 1/4 turn of the light socket DO NOT TOUCH THE GLASS PART OF THE BULB WITH YOUR BARE HANDS AS THE OIL ON YOUR SKIN WILL CAUSE A HOT SPOT AND BURN THE BULB OUT WEAR GLOVES IF YOU NEED TO TOUCH THE BULB! repete process to install

    May 20, 2015 | 2009 Dodge Avenger

    1 Answer

    Change tail light in 2009 avenger


    Try looking in the trunk and pulling back the liner. If not there and you cant find any screws on the cover then it probably pops out.

    Oct 19, 2014 | 2009 Dodge Avenger

    1 Answer

    2010 Dodge Avenger Fog lights won't work


    fuse or chang the head light bulb

    Jan 15, 2014 | 2010 Dodge Avenger

    1 Answer

    How to i remove rear lens cover to change burned out light,2009 dodge avenger


    Open Trunk, There Is Some Hardware Behind The Tail Lamp That You Need To Remove, an d Then the Tail Lamp Will Come Out !!

    Jan 12, 2011 | 2009 Dodge Avenger

    1 Answer

    Gauges dont light up!!


    Dimmer switch is likely shorted out if the fuse is good. Common problem.

    Jul 29, 2010 | 1996 Dodge Avenger

    2 Answers

    2008 Dodge Avenger SE - Short in lights but where??


    Just because the bulbs look fine, doesn't mean they are. Start with the bulb replacement. If this doesn't solve it, and it has under 36K, it should still be under factory warranty. Shouldn't cost anywhere near $200 either way.

    Jun 15, 2009 | 2008 Dodge Avenger

    2 Answers

    How to change a headlight bulb on a 1999 dodge avenger?


    You have to open the hood and go at it from behind the bulb. look behind the light fixture set up and you will see where the light bulb goes. Simply twist off and pull out. the old light bulb will com out also.

    Apr 14, 2009 | 1999 Dodge Avenger

    1 Answer

    How to replace fog lights on 1998 Dodge Avenger ES


    you need to take off the buttom shields and then you should be able to get to the fog lights

    Jan 25, 2009 | 1998 Dodge Avenger

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    40 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...