Question about Ford Taurus

Open Question

How to remove k frame from 2004 ford taurus

Need frame replaced

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: Remove the Passenger side door frame on a 2002 Ford Explorer

    Lift up on the switch plate until it snaps out ,remove the bolt from under there and the bolts along the bottom of the panel. There may be a few others so look around. When all are removed lift up on the door panel(DO NOT pull towards you it will destroy the panel). Your mirror is now accessible.

Posted on Nov 29, 2008

Ad
  • 140 Answers

SOURCE: what is the spark plug gap for a 2004 ford taurus

Hello, go to www.autozone.com and put your car in the "manage my vehicles" tab and then click on the "Repair info" tab and click on the links to get just about any info you need. If you need help just ask. Good luck.

Posted on Jan 23, 2009

alicantecoli
  • 22156 Answers

SOURCE: I need the wiring diagram for the factory stereo 2004 ford taurus

go to the dealer ,parts dept and ask nicely and they will print out the parts page for that area

Posted on Jan 02, 2010

  • 14036 Answers

SOURCE: need a fuse box diagram for a 2004 ford taurus

GO TO AUTO ZONE OR ADVANCE AUTO PART BUY A HAYNES REPAIR MANUAL FOR YOUR CAR.IT HAS ALL THE ELECTRICAL DIAGRAMS.

Posted on Mar 05, 2010

toyladi3
  • 597 Answers

SOURCE: I need help changing spark plugs in my 2004 ford

Hello,

You will have to remove the intake assembly to be able to remove the spark plug. You can also go about it from the ignition coil. To replace the spark plug, please follow the steps below to do so. You will be needing these instruments: Phillips screwdriver, Socket wrench, Spark plug socket, Anti-seize compound, Dielectric compound, Small screwdriver, then follow the steps:

  1. Disconnect the car's negative battery cable at a time when the engine is cool.
  2. Unscrew the individual ignition coil using a screwdriver and then remove the coil and set it aside.
  3. Pull out the spark plug wire at the plug end, grasping it by the boot and twisting it out; a special tool for this is available. Disconnect the same wire at the ignition coil.
  4. Clean out the spark plug's hole, using compressed air to blow out all dust, dirt and debris from inside.
  5. Remove the spark plug from the engine using a socket wrench with a spark plug socket; turn the plug counterclockwise to remove it.
  6. Apply a thin coat of anti-seize compound to the threads of the replacement spark plug. Make sure you get no compound on the plug's electrodes.
  7. Thread the spark plug into its hole, making sure you don't cross-thread it, and then tighten it with the wrench and spark plug socket.
  8. Coat the insides of the spark plug boots with dielectric compound; use a small screwdriver to apply the compound.
  9. Install the ignition coil and screw it into place.
  10. Repeat the above steps for each spark plug/wire that needs changing and installation.
  11. Reconnect the negative battery cable once you've installed all necessary plus and wires
Hope this helped. Thank You for using FixYa!!!

Posted on Jan 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Taurus serpentine 3.0diagram


Robert, Serpentine belt diagram. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Install Replace Serpentine Belt Ford Taurus 3 0L V6 1AAuto com
2003 Ford Taurus V6 3 0L Serpentine Belt Diagrams serpentinebelthq com
2003 Ford Taurus Belt Diagram Am Having Problem Getting My

Aug 17, 2016 | 2004 Ford Taurus

1 Answer

How to replace a water pump on a 2004 ford taurus


Wanda, Check out the video and links I posted to see how to remove and replace Taurus water pump.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Install Water Pump Ford 3 0L V6 FWD WP 9038 AW4094
Ford Taurus Water pump Replacement
Need step by step water pump change
2004 Ford Taurus water pump Google Search

May 31, 2016 | 2004 Ford Taurus

1 Answer

I need printable instructions on removing and


sorry iam in spain and have no access to this sort of information,but if you ask a local mechanic iam sure they will do it for you with no need of a manual

Nov 02, 2013 | 2004 Ford Taurus

1 Answer

NEED TO REPLACE FLEX PLATE


This is a big job, this is listed as a 2004 ford taurus you will need a engine support bar and a ****** jack, a car lift will also be needed, doing this on the ground can be done but makes things alot harder. the trannys electricl connectors unhooked and also the battery removed for room. next you will want to drain the ****** oil.install the engine suppurt bar , this bar will hold the engine and ****** in car when the lower frame is removed. you will remove the air filter box. raise car and remove flex plate cover and starter. next remove bolts that hold flex plate to ****** converter.with engine support in place you will unbolt and remove ****** mounts frt ,rear and leftside. note the only thing holding the engine is the rightside mount and bar.remove the drive axles, unbolt lower control arms at lower balljoint and remove axle nuts, then axles will come out. next is to unbolt steering rack from the frame.dissconnect ****** lines from ******.remove exhaust system front pipes with converters, (Y-PIPE). next is to remove the k frame. this is the frame that holds engine and ****** inside car, becarful as engine and ****** will fall out if support bar is not installed correctly.you will need to double check for any connections in the way, with all clear and someone to help you lower the frame you will unbolt and remove it. next you will lower adjusting rod on the engine support bar to tilt engine and ****** down, the ****** will tilt down, next remove all ****** to engine bolts except one. with all bolts out except one you will install a ****** jack to hold the ******. next remove the last bolt and look around for any connection that may need to be removed. split ****** away from engine slowly always checking that all is clear. with ****** removed roll off to side or back and now you will be able to remove the flexplate. remove the bolts holding flexplate to engine mark a hole to install new one the same way. most flywheels (flexplate) only go on one way but just incase mark it. install new plate and reverse steps to but back together. note always install new starter when replacing a flexplate, this is to avoid damage to new flexplate. good day. also this job would take a tech 8 hrs.

Sep 11, 2011 | 2004 Ford Taurus

1 Answer

Is thier a way to take a tranny out without dropping the frame


NO. the bottom frame must be removed, it alot of work to remove the tranny on a ford taurus, you will need a top engine support also, this will hold the engine and trany inplace to remove the frame and then you lower this to remove tranny. good day.

May 12, 2011 | 1997 Ford Taurus

1 Answer

Fuel filter location on a 2003 ford taurus and brake light too


The fue filt on the taurus shoud be just about under the drivers seat on the frame. you need some small wrenchs 10mm to loosen clamps that hold tubing to the frame and the tool to remove ford fuel filters. $4 or $5 at advanced. The brake light should be behind the felt lining in the trunk. Turn the socket and pull it out then the bulb just pulls out.

Feb 23, 2011 | 2003 Ford Taurus

1 Answer

REPLACING THE OIL PUMP


No you can jack the motor high enough to get a 2x4 between the engine mount and frame and drop the pan,,,,,,,,,,,,,,,,, take the 2 right side engine mount bolts off from the frame ,,, raise the engine high enough to get the 2x4 between the frame and engine mounts...then drop the pan out of it

Jul 15, 2010 | 1999 Ford Taurus

1 Answer

Replace transmission


it is not recomended! that u do this task ur self! very dangerous! u have to remove the h frame ! nothing will b holding the engine! it can fall out!

Apr 02, 2010 | 1993 Ford Taurus

1 Answer

Where is the horn located on a 2004 ford taurus


they are located on the left front frame rail behind the front bumper. they are an assembly one bolt holds the horns, heres a diagram to help you.faca1e6.gif

Feb 07, 2010 | 2004 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...