Question about 2005 Buick LeSabre

Open Question

ASH TRAY LIGHT BUICK LESABRE

LIGHT BULB TO SHOW ASH TRAY AT NIGHT

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 136 Answers

SOURCE: CHECK ENGINE BULB REPLACEMENT

You have to take all the facia off the dash - and then pull the dash cluster out. It is a long hard job for a light bulb. When you take the dash out don't forget to undo the speedometer wire and then the wire plugs on the left and right upper sides of the dash unit.

Posted on Oct 13, 2008

Ad
  • 1 Answer

SOURCE: REPLACEMENT OF [LOW BEAM] HALOGEN BULB IN 2004 Buick LeSabre

I just Replaced a Low Beam Light bulb on a 2005 Buick La Sabre.

If You use a Metric socket and Remove the Two Silver bolts Attaching the headlight Assemble onto the metal surrounding the the lamp assembly it comes out to the front. This makes it much easier to access the bulb. Twist it counerclockwise & it comes out by pulling gently on the bulb. Then by realeasing a tab that is the socket holder bulb can be removed & replaced with a New #9006 low beam halogen light bulb. Wrap a Paper towel around the bulb & do NOT touch it with your bare hand as this wiil ruin a halogen bulb,

Posted on Jul 23, 2009

  • 38 Answers

SOURCE: Trying to change the turn signal bulb in a 2004 Buick Le Sabre.

it might snap in from the outside...go to a local p[arts store they may do it for u if u buy the bulb from them

Posted on Jul 25, 2009

ourhowse
  • 2007 Answers

SOURCE: replacing brake light bulb

OPen the trunk and remove the access cover. The bulbs just twist out from the rear.

Posted on Nov 18, 2009

  • 196 Answers

SOURCE: 2000 Buick Lesabre custom liscense plate bulb

kind of tricky, took me an hour to get it figured out, but you got to opend the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together

Posted on Mar 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change ashtray bulb in a Honda CR-V 2000 ?


Pull old ash tray out twist lamp outputting new lamp in remount ash tray your done .MO

Apr 02, 2017 | Honda Cars & Trucks

1 Answer

My Camry 99's gear shift indicator light, ciggarette lighter light, Air con's contoller light and ash tray lights are not working after replacing bulbs.


Could be a fuse. Check the interior firewall fuse box under the driver's side dashboard area. That's location of the fuse box. Probably wired in series....maybe wrong bulb replaced.

Dec 02, 2017 | Cars & Trucks

1 Answer

How to change ashtray light in buick century


On most models you have to take the screws out of the ash tray holder and the bulb comes out from the back side.

Dec 18, 2012 | 1997 Buick Century

1 Answer

Inside the car my turn signals blink rapidly, outside the car neither brake lights or turning signal work. i have replaced the bulbs and still nothing. at night my tail light are on but neither brake light...


Are you sure you installed the correct bulbs .Double ck you installed the bulbs in the correct socket and that the bulb #(1157)(3157) is the right bulb installed.

May 31, 2011 | 2000 Buick LeSabre

1 Answer

How do you re-install the ash tray with the 2 springs?


2000 buick lesabre two ashtrays.Where do you find the springs too replace them.

Aug 24, 2010 | 2000 Buick LeSabre

1 Answer

1. At night there is zero illumination for temp control knobs. It's completely dark. 2. Dash gauges very difficult to read at dusk and night time. (windows are tinted dark) by previous owner. doesn't go...


The HVAC control, if it is the Electronic version, you might want to try unplugging, and plugging it back in. Remove the center trim panel by opening the ash tray, and pulling on each corner. The trim panel is held on with 6 spring clips ( 3 on each side ).
6e3d291.jpg
When you have the panel loose ( don't move too far, the HVAC controls and the Passenger Airbga Deactivated light are still hooked up ), un hook the 2 cam over connectors ( circled in blue ). After hooking back up, the HVAC will be off, you need to manually turn it on.
2. The dash lights could be the wrong bulb, or some could be blown out. F150online.com -> Technical Articles section has a thread on removing the dash to change the bulbs.

These are the 2 starting points.

Aug 08, 2010 | 2006 Ford F-150

1 Answer

2000 pontiac montana. I want to replace the driving ligh bulbs. the under the headlights what size is it?


Fog/Driving Light Bulb Size: 880
Here is the rest of the bulb size used in your Montana.
2000 Pontiac Montana Auto Light Bulb Diagram
Low Beam Headlight Bulb Size: 9004
High Beam Headlamp Light Bulb Size: 9004
Parking Light Bulb Size: 4157NALL
Front Turn Signal Light Bulb Size: 4157NALL
Rear Turn Signal Light Bulb Size: 3156
Tail Light Bulb Size: 3057
Stop Light Bulb Size: 3057
High Mount Stop Light Bulb Size: Assembly
Fog/Driving Light Bulb Size: 880
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 3156
Front Sidemarker Light Bulb Size: 194
Ash Tray Light Bulb Size: 558
Glove Box Light Bulb Size: 194
Map Light Bulb Size: 168
Dome Light Bulb Size: 562
Step/Courtesy Light Bulb Size: 168
Trunk/Cargo Area Light Bulb Size: 212-2
Daytime Running Light Bulb Size: 3157NALL
Thank you for using fixya.


Apr 30, 2010 | 2000 Pontiac Montana

1 Answer

Volvo 780 bertone. the brake lights are not working.


OK. Several ideas. The 760 is really a 740 with a fancy body. Start with the brake light switch on the brake pedal. Use a short jumper with two alligator clips to bypass the switch. If the brake light works, bingo! A good substitute for the jumper is a cheap 12 volt test light from AutoZone or Sears. Clip one end to a good ground, and probe for voltage with the sharp tip. If the bulb lights on one side of a switch, you have 12 volts coming in. If you activate the switch and there's not 12 volts on the other side, the switch is suspect. Check the fuse. The fuse functions are labelled on the iunside of the ash tray door. Check the @#$%^@# bulb sensor in the relay rack behind the ash tray. It's the big, round red relay in the rear left position closest to the firewall. Failure there can knock your brake lights out. A used one fetches about $10 on ebay. I always carry a spare. You didn't tell me if all the brake lights are out, or just one. If they're all out, it's a systemic problem. One out, it';s usually a bulp or bad socket.

Mar 16, 2010 | 1990 Volvo 780

Not finding what you are looking for?
2005 Buick LeSabre Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...