Question about 2006 Mitsubishi Colt

Open Question

How to change headlight bulb on mitsubishi colt

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 166 Answers

SOURCE: how do I change my headlight bulb

go to your parts suppler and ask for a H4 globe pop your bonnet and remove the plug on the back of your head light then remove the rubber boot paying attention to which way it cam off then you will find a spring clip unclip it but be careful not to damage its anchor point. remove old globe an throw away take new globe out of box DO NOT TOTCH THE GLASS OF THE GLOB AS IT WILL CAUSE THE GLOBE TO BLOW STAAIGHT AWAY AFTER FITTING IT handle the globe by the metle bass and fit it, refit spring clip and rubber boot fit the plugf and check the operation of the light

bingo you are done have a nice day

Posted on Dec 21, 2008

MrScary66613
  • 1990 Answers

SOURCE: How do you change the coolant on a Mitsubishi Colt Model RD 1988

Leave your Radiator Cap on for Preassure and look at your Radiator from Underneath. Should be at the Very bottom facing the Motor. Looks like a Wing Nut. Slowly Loosen this Wing Nut and your Coolant will Drain. The cap is left on to pull the Coolant out of the Block as you do this a Little bit into this you can Take the Radiator Cap loose and it will speed it up.

Posted on Jan 01, 2009

  • 1 Answer

SOURCE: How to change the headlight bulb on a 2001 mitsubishi galant?

On either side of the headlight wiring assembly, in the engine compartment, you will find 2 small tabs. They are located to the sides and towards the bulb of the plastic assembly. Press these 2 tabs in while pulling the wire assembly out. Remove the rubber gasket and unhook the wire spring holding the bulb in place. The bulb come right out. The bulbs are halogen so do not handle the new bulb by the glass.

Posted on May 08, 2009

  • 1 Answer

SOURCE: how do you replace a nearside headlight bulb on a

There is an access point in the wheel arch. remove cover to reveal the back of the headlight cover. just done mine. its fiddly.

Posted on Jan 18, 2010

  • 4793 Answers

SOURCE: Can anyone tell me how

they cant do it cos like most modern (stupid designs)you have to take off most of the front end........(not quiet)

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a passenger headlight bulb on a 2008 Mitsubishi Colt and is it a difficult job?


usually they just unplug from the back twist and pull . do not touch the glass part when putting in the new one or it will not last

Oct 01, 2015 | Mitsubishi Cars & Trucks

1 Answer

How do I replace the passenger side headlight bulb on a 2008 Mitsubishi Colt and is it a difficult job?


Probably a quick and straightforward process:
Go to local parts store to get replacement bulb. If it is the type that fits into a holder, continue.........
- Open hood
- Look at back of bad headlight
- Wire will go to Back of light to bulb holder
- Twist holder counter clockwise to remove
- Pull out old bulb
- Insert new bulb
- Reverse rest of process.
Cheers

Oct 01, 2015 | Mitsubishi Cars & Trucks

1 Answer

How to change headlight on 2000 galant


  • 1
    Place the Mitsubishi on a flat service in park. Set the parking brake before continuing.

  • 2Open the Galant's hood and locate the headlight cover -- roughly 3-inch wide circular piece of plastic -- behind the headlight bulb intended for replacement. Turn this cover clockwise to unlock it and pull it from the headlight assembly, exposing the headlight socket below it.


    3

    Hold the rear of the headlight socket and turn it counterclockwise to unlock it. Pull the headlight socket and bulb from the headlight assembly.


    4

    Grab the bulb and pull it from the socket with a slight wiggling motion.


    5

    Pick up the new 9003 headlight bulb using a clean, lint-free cloth and line up its prong with the slots in the socket. Never tough the bulb with your bare hands, as the oils left by your hands can cause the bulb to burn out prematurely.


    6

    Slide the socket and new bulb into the headlight assembly and turn the socket clockwise to lock it into place.


    7

    Place the plastic cover behind the bulb and turn it counterclockwise to lock it into place.


    8

    Repeat Steps 1 through 7 for the headlight bulb on the other side of the Galant, if needed.


    9Close the Galant's hood.


    Read more: How to Put in a Headlight Bulb on a 2000 Mitsubishi Galant ' eHow.com http://www.ehow.com/how_8210819_put-bulb-2000-mitsubishi-galant.html#ixzz27iQwCdOe

    Sep 27, 2012 | 2000 Mitsubishi Galant

    1 Answer

    Need to replace a near side headlight on a Mitsubishi colt 2006. I've heard from a mate that I have to access the bulb holder through the wheel arch? Is this true? Could anyone advise me on how to go...


    there's an access panel in top/front of the front wheel arch, if it's the left bulb lock the wheels to the right, if it's the right bulb, lock the wheels to the left.
    there's two release catches on the arch panel, one to the top & one near the body of the car, release these then just slide off to reveal the back of the light housing. This has one clip at the bottom and two locating tabs at the top.
    (Opening the hood will give more light & helps when putting the inner light housing back on as you can feel if the top tabs are located back in.)
    The bulb/wires just pull out of the fitting, and then pull the bulb out of the wiring block.
    Replacement bulb just pushes into the wiring block, then just push back into the housing (the tab on the bulb locates at the top of the fitting).
    It's also worth checking if the fuse in the glove box has blown too.

    Dec 08, 2010 | 2006 Mitsubishi Colt

    1 Answer

    Headlights not working. Full beam and side lights are working.


    change your light bulbs, because they have two function
    check fuses first
    if non of that is the problem then you will need a new light switch

    Dec 05, 2010 | 2006 Mitsubishi Colt

    1 Answer

    Can anyone tell me how to change the headlight bulbs on a 2006 mitsubishi colt? Halfords apparently can't do it!


    they cant do it cos like most modern (stupid designs)you have to take off most of the front end........(not quiet)

    Oct 04, 2010 | 2006 Mitsubishi Colt

    1 Answer

    Blowing headlite bulbs


    i work in a garage and i can say chevy is junk, we get 10 chevys to 1-2 other car makes your best bet is to not tell any one about the problem and sell it, im not favoring any vehicle makers but thats the way it is sorry

    Feb 14, 2009 | 2006 Mitsubishi Colt

    Not finding what you are looking for?
    2006 Mitsubishi Colt Logo

    Related Topics:

    140 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...