Question about Ford Expedition

Open Question

Ford expedition engine block heater cord - Expedition Ford Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
virgils
  • 39 Answers

SOURCE: diagram bypass heater cord on 2001 ford expedition eddie bauer

the heater bypass is quite simple, if you look at the firewall you will see two medium sized coolant lines, remove them from the firewall and link them together using a proper sized tube, you can purchase a kit at a parts store quite cheaply

Posted on Oct 11, 2008

Ad
bunnydawg
  • 5158 Answers

SOURCE: I cannot find the block heater plug for 2000 ford f350 diesel

if you are certain that one is even installed... look around the headlights on the inside of the car.... they often have the cord fed thru that area.

Robert

Posted on Dec 16, 2008

  • 2 Answers

SOURCE: trying to locate block heater

If you open the hood and look at the top right corner of the radiator, you should see a small rectangular shaped rubber plug with a similar cap over it. Plug your block heater cord (mine came in a separate bag, it's about 2-3 feet long) into this and run the plug out the front of your vehicle's grill using that cap as the way to secure it to the grill.

Posted on Jan 03, 2009

  • 7 Answers

SOURCE: 97 Ford F250 diesel block heater shorts out when I plug it in

Kill power to the circuit before you use that ohm meter, or it will be popin like that block heater

Posted on Oct 17, 2009

jlisagearhea
  • 412 Answers

SOURCE: heater cord ford expedition 01

Dear Heater Core Hunter,
For your 01 expedition, that has the 5.4 liter motor in it, the heater core is located in the evaporator case assembly, where the blowermotor itself is located,This is a pretty darn good labor intensive job, if you open the passenger front door and get down onyour knees and look up underneath the dash.....that's what you're going to be removing and replacing, the heater core is inside of this black case.Please get back to me if you have any more questions...I'M HERE TO HELP!!!

Posted on Nov 20, 2009

Testimonial: "Awesome! Thanks for the response!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the block heater located on a 1999 Ford Taurus 3 litre 24 valve engine


I have never seen a factory block heater on a Taurus. If you have one, someone put it in. It could be at any of the six ports (three on each side) of the engine (really just four, no one would put it behind an engine mount. Not even Ford). Follow the cord to it. If you can't find the cord(drivers side p by the headlights), most likely you don't have one..

Nov 14, 2014 | 1999 Ford Taurus

1 Answer

Where is the engine block heater plug in cord?


This car does not come standard with a block heater You need to have a heater installed if you want one

Jan 03, 2013 | 2003 Ford Crown Victoria

2 Answers

Is there a fuse or relay for the heater in my 2002 ford expedition


No hot air is due to low coolant, or even poor coolant flow. The engine heats up the coolant, and it passed through your heater core, and the heater blower motor pushes air through the heater core to warm up the air. If your "fan"is working, but the air is cold, make sure your coolant level is good.

Dec 08, 2011 | 2002 Ford Expedition

1 Answer

Where does the block heater cord plug into the block heater on the engine? 2005 ford focus zx4


It is almost on the top of the engine at the back when standing against the front bumper. Use a small mirror and run it across the back of the engine, you will see a small brass rectangular piece with 2 prongs inside it. That is where you plug your cord into

Dec 18, 2010 | Ford Focus Cars & Trucks

1 Answer

Locate heater hose in a 2000 ford expedition


Expedition and Navigator

b2302e3.jpg

Fig. 7 Remove the A/C plenum demister screw and remove the A/C plenum demister adapter

fe987d3.jpg

Fig. 8 Disconnect the vacuum line

468b3b9.jpg

Fig. 9 Remove the heater core bracket

a0086be.jpg

Fig. 10 Remove the 13 retaining screws and remove the plenum chamber top

7e3c78a.jpg

Fig. 11 Remove the heater core
  1. Disconnect the battery ground cable.
  2. Drain and recycle the engine coolant.
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the instrument panel. Refer to .
  2. If equipped with the 5.4L 4V engine, remove the junction block splash shield.
  3. If equipped with the 5.4L 4V engine, remove the bolts and disconnect the cable ends from the starter relay.
  4. If equipped with the 5.4L 4V engine, remove the junction block bracket.
  5. Disconnect the heater core hose couplings.
  6. Remove the retaining screw and remove the A/C plenum demister adapter.
  7. Disconnect the vacuum line from the A/C plenum demister adapter.
  8. Remove the heater core bracket.
  9. Remove the 13 plenum chamber top retaining screws.
  10. Remove the plenum chamber top.
  11. Remove the blend door assembly from the case.
  12. Remove the heater core.To install:
  13. The installation is the reverse of the removal.
Also this VIDEO can help to solve your problem...

Hope this help.

Apr 26, 2010 | 2000 Ford Expedition

1 Answer

Heater core replacement 1999 expedition


Heater Core 1. Disconnect the battery ground cable 2. Drain the engine coolant. 3. Remove the instrumental panel. 4. If equipped with the 5.4L 4V engine, remove the junction block splash shield. 5. If equipped with the 5.4L 4V engine, remove the bolts and disconnect the cable ends from the starter relay. 6. If equipped with the 5.4L 4V engine, remove the junction block bracket. 7. Disconnect the heater core hose couplings. 8. Remove the retaining screw and remove the A/C plenum demister adapter. 9. Disconnect the vacuum line from the A/C plenum demister adapter. 10. Remove the heater core bracket. 11. Remove the 13 plenum chamber top retaining screws. 12. Remove the plenum chamber top. 13. Remove the blend door assembly from the case. 14. Remove the heater core. 15. The installation is the reverse of the removal.
The heater core should be encased in a box up inside the dash.The best way to find this is to locate the heater hoses that go through the fire wall(about 1 1/4 in diameter).This is a very tight job and you will spend most of you time laying on the floor taking out screws.Be careful not to loose any of the heater core casing screws or bolts and when refilling the coolant system fill the radiator directly,start the engine with the radiator cap off,the level will drop,fill the radiator the rest of the way and replace the cap,allow the engine to reach normal operating temp.(about 10 to 15 minutes)so that the themostat will open and then allow the engine to cool and recheck fluid level.

Jan 01, 2010 | 1999 Ford Expedition

1 Answer

Where is the heater core hose in my 2000 ford expedition?


check closer to just underneath the firewall--it could be a smaller problem than a heater core--Ford 4.6--5.4 engines have a tube just underneath the intake manifold that the rubber hose goes bad and it will leak towards the back of the engine.Lets hope so-what i hear its very expensive to change a heater core in an Expedition.

May 01, 2009 | 2000 Ford Expedition

2 Answers

Location of block heater cable on 05 F350 diesel


The block heater is already installed in your 6.0. The cord may not be there as it is an option in some states and standard equipment in others. The best way to see if your cord is there is to crawl under and look up by the # 4 cyl and you will either see 2 prongs sticking out for the cord or you will see the cord. The cord should end in the front bumper behind where the front tag would be. If you dont have the cord Id suggest getting it off ebay as it should be cheaper than the dealer. Hope this helps.

Dec 22, 2008 | 2005 Ford F 350 Super Duty

2 Answers

Trying to locate block heater onmy 2006 ford expedition


Not under hood at front of either fender or maybe behind grille. Plug may have a black plastic cover over it, so look real close.

Dec 13, 2008 | 2006 Ford Expedition

2 Answers

Diagram bypass heater cord on 2001 ford expedition eddie bauer


the heater bypass is quite simple, if you look at the firewall you will see two medium sized coolant lines, remove them from the firewall and link them together using a proper sized tube, you can purchase a kit at a parts store quite cheaply

Sep 12, 2008 | 2001 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...