Question about 2003 Jaguar X-Type

2 Answers

How to replace valve cover gasket on 2003 jaguar x type

I loosen all the bolts around the valve cover but I don't know how to remove the sensor next to the filler cap

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Did you find a solution for your is issue I'm having the same issue

Posted on May 14, 2014

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 645 Answers

The 2.5-liter X-Type gets a 194-horsepower and the 231-hp 3.0-liter V-6 model gets an increase to 231 horsepower.------------------------------------------------Car cable & OBD Connector

Posted on Dec 11, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22265 Answers

SOURCE: i need to replace the valve cover gaskets on a Jaguar XJ8 2001

easy to change,temporary measure is cover them with silicone instant gasket

Posted on Feb 18, 2009

emissionwiz
  • 77169 Answers

SOURCE: 2001 jaguar S type v 6. I need to replace the Valve cover gasket.

Felpro brand gaskets are the best in the world, not sure about the intake, if it is in the way then yes remove it.

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble removing valve cover on the right side (passengers side) of the engine on a 1996 mark viii. Help


  1. Remove engine appearance cover retaining bolt and nuts.Remove engine appearance cover from vehicle.

  1. Disconnect engine control sensor wiring at intake air temperature sensor (IAT sensor) connector and crankcase ventilation tube from air cleaner outlet tube.
  2. Completely loosen air cleaner outlet tube to throttle body bolt (captured bolt).
  3. Loosen clamp on air cleaner outlet tube to engine air cleaner (ACL) and disconnect air cleaner outlet tube.
  4. Remove remaining bolt from support bracket clamp on RH valve cover to air cleaner outlet tube.
  5. Remove air cleaner outlet tube and engine intake air resonator.


  1. Remove two retaining nuts from engine air cleaner outlet tube bracket to valve cover and remove engine air cleaner outlet tube bracket.
  2. Remove four nuts retaining RH ignition wire cover and remove cover.
  3. Disconnect ignition wires from spark plugs with a gentle twist! pull motion on the spark plug boot. Remove spark plugs.
CAUTION: Do not pull on the ignition wire as it may separate from the connector in the boot.
  1. Remove bolts and studs retaining RH valve cover to cylinder head.
  2. Remove valve cover.

Sep 28, 2017 | Cars & Trucks

1 Answer

Don't know where to poor my oil in my 1981 ford f100. there is not filler tube


there shouldn't be a filler tube, just a dipstick tube for checking the oil level. to put the oil in the engine, there should be a oil cap on the right hand side valve cover. if the dipstick tube isn't there, you definitely need to get one from a parts yard or store, you can be losing oil from the dipstick hole that goes to the oil pan...

Jan 15, 2013 | 1981 Ford F 100

1 Answer

How do i change a fuel pump of a honda accord 1996


need to disconnect negative battery cable remove fuel filler cap then you need to relief fuel pressure by using box end wrench 6mm you need to loosen 6mm service bolt at top of fuel filter need hold bango bolt with another wrench.use shop rag when loosen 6mm bango bolt to catch the fuel. you have to drop fuel tank but you need to disconnect fuel pump electrical connector in the trunk,remove 2 way valve cover fuel hose protector, then diswconnect fuel lines.

Sep 29, 2012 | 1996 Honda Accord

2 Answers

I have a 1999 Mitsubishi Galant and need to know how to put on a valve cover gasket. Oil is leaking out and dripping and it's causing it to burn and smoke comes out of the car.


Instructions
    • 1 Allow the car to cool. Disconnect the battery terminal. Remove the right side vent screen top extension. Disconnect the ignition coil with power transistor and its wiring and brackets.
    • 2 Disconnect the left hand side coil wires and spark plug wires. Remove the spark plug wires, valve cover bolts and the valve cover. Unplug the electrical connections from the intake manifold runner control actuator. Unfasten the actuator retaining the screws, right bank heated oxygen sensor front and rear.
    • 3 Remove the heated positive crankcase ventilation (PCV) valve. Remove the heated oxygen sensor plug and the Differential Pressure Feedback EGR (DPFE) sensor. Disconnect the ignition coil with power transistor and its wiring and bracket. Remove the valve cover bolts, the valve cover and the old valve cover gasket. Clean the valve cover seating area with automotive engine cleaner and place the new gasket in the gasket seating area.
    • 4 Replace the parts that were removed and disconnected by reversing the steps. Replace the valve cover gasket and tighten the bolts, in sequence, ensuring not to over tighten. Put back the ignition coil with power transistor and its wiring and bracket, the heated positive crankcase ventilation (PCV) valve, the heated oxygen sensor plug and the Differential Pressure Feedback EGR (DPFE) sensor.
    • 5 Add oil to the car. Start the car and let it run at idle for a while to check for leaks..

Aug 18, 2011 | 1999 Mitsubishi Galant

2 Answers

My '98 Catera needs the #1 cyl ignition coil replaced,plus the valve cover gaskets.Is all of this readily accessible when the air cleaner is removed?Or,more importantly,how many components must be...


Not easy but doable. I would mark anything you aren't familiar with to get it back together right. Please let me know if you have any questions, and thanks for using FixYa.


IGNITION COIL REMOVAL & INSTALLATION
3.0L Engine
  1. Remove the wiper arms
  2. Remove the left and right side air inlet grilles
  3. Remove the wiper motor.
  4. Detach the power brake booster vacuum connection from the intake plenum.
  5. Disconnect the spark plug wiring harness from the ignition coil.
  6. Detach the electrical connection from the ignition coil.
  7. Remove the bolts from the ignition coil, and remove the coil.

To install:
  1. Installation is the reversal of the removal procedure.
  2. Tighten the coil bolts to 71 inch lbs. 8 (Nm).
  3. Tighten the power brake booster vacuum connection until snug.

valve cover removal & installation3.0L Engine
RIGHT
  1. Disconnect the negative battery cable.
  2. Remove the intake plenum and the intake manifold.
  3. Remove the spark plug boots from the spark plugs, and then the wires from the routing retainers. Make sure they are tagged for proper installation.
  4. Remove the rocker arm cover-to-cylinder screws, the cover, and the gasket/seals. Discard the seals.


NOTE Ensure all eight sealing O-rings are accounted for. They may stick to the camshaft bearing caps or fall into the oil return journals in the cylinder head.
jturcotte_1756.gif

Fig. The location of the valve cover O-rings is shown here


jturcotte_1757.gif

Fig. The valve cover sealant application points
To install:

  1. Install new valve cover seals. Lightly coat the new seals, including O-rings, with engine oil prior to installation. The oil application will assist in holding the O-ring seals to the valve cover.
  2. Apply a thin coat of silicone sealer at the front and back of the seals.
  3. Install the valve cover to the cylinder head, and tighten the bolts to 71 inch lbs. (8 Nm).
  4. Route the spark plug wires into the retainers, and install the plug boots to the spark plugs.
  5. Replace the intake manifold and the intake plenum.
  6. Connect the negative battery cable.
LEFT
  1. Disconnect the negative battery cable.
  2. Remove the intake plenum and the intake manifold.
  3. Remove the spark plug boots from the spark plugs, and then the wires from the routing retainers. Make sure they are tagged for proper installation.
  4. Remove the oil filler spout.
    1. Unlock the tab.
    2. Twist counterclockwise.

  5. Remove the rocker arm cover-to-cylinder screws, the cover, and the gasket/seals. Discard the seals.

NOTE Ensure all eight sealing O-rings are accounted for. They may stick to the camshaft bearing caps or fall into the oil return journals in the cylinder head.
To install:
  1. Install new valve cover seals. Lightly coat the new seals, including O-rings, with engine oil prior to installation. The oil application will assist in holding the O-ring seals to the valve cover.
  2. Apply a thin coat of silicone sealer at the front and back of the seals.
  3. Install the valve cover to the cylinder head, and tighten the bolts to 71 inch lbs. (8 Nm).
  4. Install the oil filler spout.
    1. Insert the spout and twist clockwise.
    2. Ensure the locking tab seats on the valve cover bolt head.

  5. Route the spark plug wires into the retainers, and install the plug boots to the spark plugs.
  6. Replace the intake manifold and the intake plenum.
  7. Connect the negative battery cable.

INTAKE MANIFOLD REMOVAL & INSTALLATION

3.0L Engine
This vehicle uses a sequential multiport fuel injected engine. Fuel injector connectors must be positioned onto their appropriate fuel injector or engine performance and exhaust emissions may be seriously affected. Fuel injector connectors are numbered to match their cylinders.
  1. Remove the intake plenum.
  2. Properly relieve the fuel system pressure.
  3. Remove the fuel supply and fuel return hose from the fuel rail.
  4. Fuel injector electrical harness connector.
  5. Remove the intake manifold bolts and the intake manifold.


NOTE Mask off the ports to the intake manifold spacer. If foreign objects enter the engine, severe damage may result.
Clean the intake manifold sealing surfaces with a non-abrasive tool or solvent.
Do not damage machined aluminum surfaces or improper sealing may occur.


jturcotte_1758.gif

Fig. Location of the guide pins for the intake plenum-3.0L engine


jturcotte_1759.gif

Fig. Intake plenum-to-intake manifold mounting


jturcotte_1760.gif

Fig. The intake manifold bolt locations
To install:

  1. Remove the masking from the intake ports.
  2. Install the intake manifold, and tighten the intake bolts to 15 ft. lbs. (20 Nm), rotating the tightening sequence.
  3. Reconnect the fuel injector electrical harness connector.
  4. Couple the fuel supply and fuel return hose,. Tighten the connection to 11 ft. lbs. (15 Nm).


NOTE Counterhold the connections to prevent damage to the fuel rail.
  1. Install the intake plenum.
  2. Connect the negative battery cable.

May 24, 2011 | 1998 Cadillac Catera

1 Answer

I need a print out of how i can change out a head gasket on a 1995 mercury cougar


Removal
  1. Drain engine cooling system.
  1. Disconnect battery ground cable (14301) .
  1. Remove engine air cleaner (ACL) (9600) including air cleaner outlet tube (9B659) .
  1. Loosen drive belt tensioner (6B209). Remove drive belts (8620) .
  1. If LH cylinder head (6049) is being removed, perform the following:
    1. Remove oil filler cap (6766) .
    1. Remove power steering pump front mounting bracket retaining bolts.
    1. Remove generator (GEN) (10346) and belt idler pulley (8678).
    1. Remove power steering pump/generator bracket retaining bolts. Leave hoses connected, place pump/bracket assembly aside in a position to prevent fluid from leaking out.
  1. If RH cylinder head is being removed, perform the following:
    1. Remove drive belts .
    1. If equipped with A/C, remove mounting bracket retaining bolts. Leave hoses connected and position A/C compressor (19703) aside.
    1. Remove positive crankcase ventilation valve (PCV valve) (6A666) .
  1. Remove upper intake manifold (9424) .
  1. Remove valve cover retaining bolts.
  1. Remove fuel injection supply manifold (9F792).
  1. Remove lower intake manifold as outlined.
  1. Remove exhaust manifolds (9430) as outlined.
  1. Loosen rocker arm seat retaining bolts enough to allow rocker arm (6564) to be lifted off the push rod (6565) and rotate to one side.
  1. Remove push rods . Identify position of each push rod . Push rods should be installed in their original position during assembly.
  1. Remove cylinder head retaining bolts and discard.
  1. Remove cylinder heads .
  1. Remove and discard old head gaskets (6051) .
Installation
  1. NOTE: Lightly oil all bolts and stud bolt threads before installation except those specifying special sealant.
    Clean cylinder head, intake manifold , valve cover (6582) and head gasket surfaces. If cylinder head was removed for head gasket replacement, check flatness and sealing areas for scratches of cylinder head and cylinder block gasket surfaces. Refer to Section 03-00 for procedure.
  2. Position new head gaskets onto cylinder block (6010) using cylinder head to block dowels (6A008) for alignment.

    Head Gasket


    a11431c.gif

  3. Position cylinder heads onto cylinder block .
  4. ani_caut.gif CAUTION: Always use new cylinder head bolts to ensure a leak-tight assembly. Torque retention with used bolts can vary, which may result in coolant or compression leakage at the cylinder head mating surface area.
    -ft).
  5. For 3.8L non-SC engine, tighten cylinder head retaining bolts in numerical sequence in three steps as follows:
    1. 20 Nm (15 Lb-Ft)
    1. 40 Nm (29 Lb-Ft)
    1. 50 Nm (37 Lb-Ft)
  6. ani_caut.gif CAUTION: Do not loosen all of the bolts at the same time, only work on one bolt at a time or possible damage to engine or leakage may occur.
    In sequence, loosen retaining bolts two to three revolutions and retighten bolts one at a time in the following manner:
    1. Long bolts:
      • 15-25 Nm (11-18 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.
    1. Short bolts:
      • 10-20 Nm (7-15 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.


      a11399c.gif


      Item Part Number Description 1 6010 Cylinder Block 2 - Locating Pin (2 Req'd) 3 N802515-S Cylinder Head Bolt (4 Req'd Each Side) 4 6049 Cylinder Head 5 N802516-S Cylinder Head Bolt (4 Req'd Each Side) 6 6A008 Cylinder Head to Block Dowel
  7. NOTE: If original valve train components are being installed, a valve clearance check is not required. If a component has been replaced, perform a valve clearance check as outlined.
    Dip each push rod end in Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A and install push rods in their original position.
  8. For each valve, rotate crankshaft (6303) until valve tappet (6500) rests on the heel (base circle) of the camshaft lobe, before tightening rocker arm seat retaining bolts to 7-15 Nm (5-11 lb-ft) maximum.
  9. Lubricate all rocker arms with Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A. Final-tighten the rocker arm seat bolts to 30-40 Nm (22-30 lb-ft). For final tightening, camshaft (6250) may be in any position.
  10. Install exhaust manifolds as outlined.
  11. Install lower intake manifold as outlined.
  12. Install fuel injection supply manifold .
  13. Position valve cover and new valve cover gasket (6584) on cylinder head and install retaining bolts. Note location of ignition wire routing clip stud bolts. Tighten retaining bolts to 9-12 Nm (7-9 lb-ft).
  14. Install upper intake manifold .Install spark plugs (12405) , if removed.
  15. Connect ignition wires to the spark plugs .
  16. If LH cylinder head is being installed, perform the following:
    1. Install oil filler cap.
    1. Install generator/power steering pump mounting bracket.
    1. Install generator .
    1. Install main accessory drive belt tensioner .
    1. Install power steering pump (3A674) .
    1. Install power steering pump support bracket.If RH cylinder head is being installed, perform the following:
    1. Install positive crankcase ventilation valve .
    1. If equipped with A/C, install A/C compressor mounting brackets (2882) and A/C compressor .
  17. Install drive belt and tighten to specification.
  18. Connect battery ground cable .
  19. Install air cleaner outlet tube.
2010&c18=modelyear&c35=wsm%2ccylinder%20heads%2cssd%2c03-01a%2cin-vehicle%20service&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 06, 2011 | Mercury Cougar Cars & Trucks

1 Answer

Replacement of timing belt on 2001 daiwoo legansa


This should give you a clue as to how to replace the timing belt on the camshaft pulleys.prev.gif next.gif Camshaft and Valve Lifters REMOVAL & INSTALLATION 1.6L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Timing belt
    • Crankcase ventilation tube from the valve cover
    • Spark plug cover bolts and the cover
    • Camshaft Position (CMP) sensor connector
    • Spark plug wires from the plugs
    • Valve cover nuts, washers, cover and gasket
    NOTE: Be very careful not to nick or scratch the camshafts.
  4. Hold the flats of the intake camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  5. Hold the flats of the exhaust camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  6. Mark the camshaft cap locations so that they may be returned to their original positions.
  7. Remove the camshaft cap bolts in the sequence illustrated.
  8. Remove the caps and the camshafts. Fig. 1: Loosen the camshaft cap bolts in this sequence using several passes - 1.6L engine 9307zg85.gif
    To install:
  9. Lubricate the camshafts and caps with engine oil.
  10. Install the caps and the camshafts in their original positions.
  11. Tighten the camshaft cap bolts in the sequence illustrated to 12 ft. lbs. (16 Nm). Fig. 2: Tighten the camshaft cap bolts in the sequence illustrated using several passes - 1.6L engine 9307zg84.gif

  12. Measure the camshaft endplay on both camshafts. The endplay should be 0.003-0.009 in. (0.10-0.25mm).
  13. Install the intake camshaft gear. Hold the flats of the intake camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 49 ft. lbs. (67 Nm).
  14. Install the exhaust camshaft gear. Hold the flats of the exhaust camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 49 ft. lbs. (67 Nm).
  15. Apply a small amount of gasket sealer to the corners of the front camshaft caps and to the top of the rear valve cover-to-cylinder head seal.
  16. Install or connect the following:
    • Valve cover, washers and nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Spark plug wires to the plugs
    • Spark plug cover and bolts. Tighten the bolts to 27 inch lbs. (3 Nm).
    • CMP sensor connector
    • Crankcase ventilation tube to the valve cover
    • Timing belt
2.0L and 2.2L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Timing belt
    • Crankcase ventilation tube from the valve cover
    • Spark plug cover bolts and the cover
    • Spark plug wires from the plugs
    • Camshaft Position (CMP) sensor connector
    • Valve cover nuts, washers, cover and gasket
    NOTE: Be very careful not to nick or scratch the camshafts.
  4. Hold the flats of the intake camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  5. Hold the flats of the exhaust camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  6. Mark the camshaft cap locations so that they may be returned to their original positions.
  7. Remove the camshaft cap bolts in several passes of one half turn each in the sequence illustrated.
  8. Remove the seal ring from the camshafts. NOTE: Make sure the camshafts detaches evenly from the bearing seats in the front guide bearing.
  9. Remove the caps and the camshafts. Fig. 3: Remove the camshaft cap bolts in several passes of one half turn each in the sequence illustrated - 2.0L and 2.2L engines 9307zg38.gif
    To install:
  10. Lubricate the camshafts and caps with engine oil.
  11. Install the caps and the camshafts in their original positions.
  12. Tighten the camshaft cap bolts in the sequence illustrated to 71 inch lbs. (8 Nm). Fig. 4: Tighten the camshaft cap bolts in the sequence illustrated using several passes - 2.0L and 2.2L engines 9307zg37.gif

  13. Measure the camshaft endplay on both camshafts. The endplay should be 0.0015-0.0056 in. (0.040-0.144mm).
  14. Install the intake camshaft gear. Hold the flats of the intake camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 37 ft. lbs. (50 Nm), retighten the bolt an additional 60 degree turn and finally an additional 15 degree turn.
  15. Install the exhaust camshaft gear. Hold the flats of the exhaust camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 37 ft. lbs. (50 Nm), retighten the bolt an additional 60 degree turn and finally an additional 15 degree turn.
  16. Install or connect the following:
    • Valve cover, washers and nuts. Tighten the nuts to 71 inch lbs. (8 Nm).
    • CMP sensor connector
    • Spark plug wires to the plugs
    • Spark plug cover and bolts. Tighten the bolts to 27 inch lbs. (3 Nm).
    • Crankcase ventilation tube to the valve cover
    • Timing belt
    • Negative battery cable

Feb 04, 2011 | 2001 Daewoo Leganza

1 Answer

We need to know how to change a valve cover gasket on a 2004 suzuki verona 2.5L ENGINE


There are probably 8 - 12 bolts/nuts that attach the valve cover to the cylinder head. Remove the bolts, clean the mating surface, install new gasket, and reattach the valve cover with the bolts.
You may need to remove the following spark plug wires vacuum lines air cleaner assembly oil filler cap

Jan 06, 2010 | 2004 Suzuki Verona

1 Answer

Removing tank


Disconnect battery ground cable. Loosen fuel filler cap. Support underneath of the fuel tank protector Disconnect evaporative fuel hose at the canister. Disconnect fuel feed hose and fuel return hose near the fuel filter. Plug both ends of the fuel hoses to prevent fuel leakage. Disconnect air breather hose and fuel filler hose at the fuel filler neck. Cover fuel hose to prevent any dust entering. Remove the four fuel tank assembly fixing bolts at four corners of the tank. Let down the tank and disconnect the wiring connectors Remove fuel tank assembly along with protectors Remove retaining cover and roll over & float valve along with the evaporative fuel hose and pipe Remove fuel pump and sender assembly by removing the snap ring with the fuel hoses Remove protectors by removing the six fixing bolts

Jun 12, 2009 | 1999 Isuzu Rodeo

3 Answers

1992 Toyota Previa van,Oil dripping onto exhaust manifold, replace head gasket? need a free manual!


The toyota previa uses a formed silicone gasket for the valve cover and the cover is held in place by metric shoulder bolts ( 10mm). The valve gasket leaks because you can't get enough preload on the bolts to re-seat the old gasket when it gets old and shrinks. The shoulder bolts only allow you to tighten the gasket enough to seat the shoulder on the bolt. If you continue to torque down the suspected bolts, you will snap the bolt off ( don't ask me how I know this ). You can either 1.)replace the old gasket with a new one or 2.) remove the existing bolts around the leak area and put in new metric bolts that do not have a shoulder. You may want to put in a small sleeve into the existing bolt hole but shorter than the thickness of the valve cover to account for the smaller diameter bolt. You can now torque down the bolt and get enough preload to seal the valve cover without removing the old gasket. Make sure you use a torque wrench ( in-lbs) or be very careful not to snap these small valve cover bolts.

May 26, 2009 | 1992 Toyota Previa

Not finding what you are looking for?
2003 Jaguar X-Type Logo

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...