Question about 1996 Toyota Corolla

Open Question

Replacing serpentine belt on toyota corolla 1996 has 3 belts

Removed belts but not marked properly and got mixed need diagram of how to reinstall belts and in what order

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: need belt schematic for 2006 toyota corolla

I can get you a diagram on monday but it goes from the alternator to the power steering pump then around the tensioner pulley then around the crank pulley then to the a/c compressor then pull on the tensioner to give you some slack and slip it on the waterpump.I hope that helps.Let me know if you still need the diagram

Posted on Nov 29, 2008

  • 383 Answers

SOURCE: need timing belt mark diagram for 95 corolla 4afe

malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.

Posted on May 06, 2009

greg_margo
  • 1959 Answers

SOURCE: I need a serpentine belt diagram for 2007 Toyota

Below is a link to a diagram. The TP is the tensioner pulley.
http://www.chiltonlibrary.com/content/images/7923/images/79234g54.gif

Posted on Jul 04, 2009

  • 194 Answers

SOURCE: need diagram for a serpentine belt of 2006 toyota corolla 1.8 wit

Is the diagram on a sticker, on the underside of the hood?

Posted on Aug 20, 2009

  • 1757 Answers

SOURCE: Need a serpentine belt diagram for 2004 Toyota

Sorry for the delayed response.
CLICK
on the following LINK. It has the Serpentine Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
Thanks.
http://www.2carpros.com/car_repair_information/year/2004/make/toyota/model/corolla/2004_toyota_corolla_drive_belt_routing_diagram.htm

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing chain installation


1996-1999 Toyota Corolla valve timing:
It is very easy to install the timing belt on 1997 Toyota Corolla. Do the following:
- Mark the numbers 1,2 and 3 on the spark plug wires with permanent marker or nail polish and remain the 4th one unmarked. This is necessary so that you can easily remember the spark plug wires order later on their original position.
- Remove the spark plugs so that the engine can easily be rotated.
- Rotate the crankshaft clockwise to align the v- groove mark on the crankshaft pulley with the 0 mark on the timing belt cover. If these marks are aligned the piston is always on the Top Dead Position (TDC).
25502648-okm0ksuj3f3lm2ubjq0dkjux-5-0.jpg

- To replace the timing belt remove the crankshaft pulley, upper and lower timing covers.
- Temporarily screw in the crankshaft bolt in its place to rotate the crankshaft with the spanner and align the v- groove of lower crankshaft gear with the index mark on the oil pump cover as shown in the following diagram.
- Inspect the cam shaft mark through the small hole on the cam shaft sprocket. The punch mark should be exactly behind the hole on the cam shaft sprocket as shown in the following diagram.


25502648-okm0ksuj3f3lm2ubjq0dkjux-5-2.jpg
- Loosen the timing bearing bolt, press the bearing forcefully against the spring with some suitable tool and lock it there temporarily.
- Remove the timing belt.
- Remove the timing bearing.
- Replace the new timing belt and bearing with the original.
- Install in the reverse order of dis-assembly.
NOTE: NEVER PUT EXTRA FORCE ON TIMING BEARING TO ADJUST THE TIMING BELT TENSION. JUST LOOSEN THE TIMING BEARING BOLT AND THE SPRING ATTACHED TO IT WILL PULL THE BEARING IT SELF WITH THE PRESET TENSION TO ADJUST THE TIMING BELT.
Thank you for visiting Fixya.

Mar 02, 2015 | 1997 Toyota Corolla

3 Answers

Belt routing diagram for1999 Toyota Corolla


Thats a 98 belt routing same engine. 99 wouldnt load1021f4c.jpg

Jul 02, 2010 | 1999 Toyota Corolla

1 Answer

Need a serpentine belt diagram for 2004 Toyota


Sorry for the delayed response.
CLICK
on the following LINK. It has the Serpentine Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
Thanks.
http://www.2carpros.com/car_repair_information/year/2004/make/toyota/model/corolla/2004_toyota_corolla_drive_belt_routing_diagram.htm

Feb 20, 2010 | 2004 Toyota Corolla

1 Answer

Replace serpentine belt


My apologies for the delayed response. I am going back to answer unanswered questions.

CLICK
on the following LINK. It has all the Diagrams for your Serpentine Belt that you will need.
If you would: Before Clicking let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/1996/make/toyota/model/corolla/1996_toyota_corolla_drive_belt_routing_diagram.htm

Nov 09, 2009 | 1996 Toyota Corolla

1 Answer

Replaciing serpentine belt on 2006 Toyota Corolla


You'll have to remove the engine cover under the bottom so you can position the new belt on the pulleys properly. Get a wrench or tensioner tool and turn the tensioner clockwise to relax the drive belt. Don't apply excessive force.

It's hard to draw a picture with words, but looking at the engine from the passenger side of the car, there are basically two top pulleys, two middle, and two bottom. The drive belt goes around the outside of the two top and two bottom, and on the inside of the two middle.

Oct 31, 2009 | 2006 Toyota Corolla

1 Answer

Need serpentine belt diagram fo r2001 toyota


if the pulley is smoth the belts back rides on that surface if it is ribbed or lined the inside of the belt rides on that surface , you local parts store should have a diagram or dealership .

Aug 27, 2009 | 2001 Toyota Corolla

1 Answer

Need diagram for a serpentine belt of 2006 toyota corolla 1.8 wit


Is the diagram on a sticker, on the underside of the hood?

Aug 20, 2009 | 2006 Toyota Corolla

1 Answer

My serpentine belt broke


not to much a rachet or a wrench their will be one marked pulley that one will be movable (springy)you just move that one and slide the belt in place if not its a alternatooer adjustment

Jun 18, 2009 | 1996 Toyota Corolla

Not finding what you are looking for?
1996 Toyota Corolla Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...