Question about 2004 Mazda 6

1 Answer

Have a 2000 mazda 626 car alarm kept going off

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 271 Answers

The individual triggers for car alarms vary widely, depending on the make and model of the vehicle, and the brand and model of the alarm itself.Usually alarms in the trunk,windows,doors and shocks contain sensors which can be triggered by vibrations.


-----------------------------------------------------
Opcom OP-Com 2010 V Can OBD2 Opel

Posted on Dec 11, 2012

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

CRTN
  • 716 Answers

SOURCE: changing the tail light bulbs on a 2000 mazda 626

The Tail Lights Are Accessed From The Inside Of The Trunk There Will Either Be A Panel Immediately Behind Where The Light Is Or Carpet. Remove It And It Will Give You Access To The Rear Of The Bolts Just Grab Twist And Pull And The Light Will Come Out.

Posted on Jan 26, 2009

  • 57 Answers

SOURCE: how do i disconnect the alarm

find the horn and look for a wire then cut the wire that goes to the alarm NOT THE HORN WIRE

Posted on Apr 15, 2009

  • 47 Answers

SOURCE: Check Engine light code 1506

this code indicates under-speed error has ocurred.
sets when PCM detects idle speed is 100 RPM lowerthan expected for 14 sec while break pedal depressedand steering wheel is straight ahead.

possible causes: IAC valve failure,intake leak,throttle body failure,opens or shorts in wiring between IAC and PCM.

Posted on Sep 16, 2009

wracefans24
  • 1985 Answers

SOURCE: How to Replace a Fuel pump on a 2000 Mazda 626

yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Posted on Dec 27, 2009

Testimonial: "Thank you didn't know if there was a tool for this."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't find low side port for 2000 mazda 626


from compressor trace large diameter line until you see port cap may be marked with L, if a/c is working low side line will be cold or cool, highside will be warm

Jul 15, 2012 | 2000 Mazda 626

1 Answer

Looking for the location of crank shaft on 2000 mazda 626


i assume you mean crank shaft sensor ,if its not on the front puilley then look around the bell housing in the most extreme awkard in accessable position possible because you can bet that is where it is

Jun 14, 2010 | 2000 Mazda 626

1 Answer

How do i know when my transmission is going bad?


Flashing check engine light when driving..2000 Mazda 626 trannys were actually made by Ford...nuff said

May 19, 2010 | 2000 Mazda 626

1 Answer

2000 mazda 626 check engine light went on . code


probley not egr valve it probley egr control solenoid or wiring

Apr 11, 2010 | 2000 Mazda 626

1 Answer

Have a mazda 626 2000 4 cyl. when i run the car


your sylinoid on ur starter is going out

Jan 20, 2010 | 2000 Mazda 626

2 Answers

I have a mazda 626 and this morning the alarm came


Pull the fuse out. If its an aftermarket alarm system it may have been plugged direct without a fuse so a total disconnection is needed at that power source

Jan 16, 2010 | 1999 Mazda 626

1 Answer

How to Replace a Fuel pump on a 2000 Mazda 626


yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Dec 26, 2009 | 2000 Mazda 626

1 Answer

How do i disconnect the alarm


find the horn and look for a wire then cut the wire that goes to the alarm NOT THE HORN WIRE

Apr 15, 2009 | Mazda 626 Cars & Trucks

1 Answer

98 626 es alarm goes off


Check if the shock sensor is too sensitive, check if the door pin switches are damaged and wire connection.

Jan 11, 2009 | 1998 Mazda 626

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...