Question about 1988 Dodge Ram 50

Open Question

Dodge ram 50 timing marks on both chains

Putting new chains in motor

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
davesm672
  • 74 Answers

SOURCE: I have a 1987 Dodge Ram 50 sport 2.6 litre the

You have to remove the oil pan - harmonic balancer - timing cover to replace timing chain... to replace cylinder head gasket and not the chain -- you need an assistant to hold the camshaft gear with chain on it. Suspending it with wire to keep the chain from moving the timing (do not let the chain relax as it will come off the crankshaft gear and change the timing)

Posted on Dec 04, 2009

Ad
  • 512 Answers

SOURCE: 3.3l dodge caravan, where to set timing chain marks

the top gear timing mark points at 6oclock...crank gear at 12 oclock

Posted on Sep 27, 2008

motor1258
  • 6674 Answers

SOURCE: timing marks for my 87 dodge ram 50 2.0

8 degrees BTDC.

Posted on Jul 26, 2009

  • 249 Answers

SOURCE: replace timing chain on 03 dodge ram 1500 with 5.7 hemi

i have an 02 and i purchased a repair manual from autozone

Posted on Jan 05, 2010

johnjohn2
  • 5763 Answers

SOURCE: need too know the timming marks on where to set

Here are the timing marks for the timing belt and also the balance shaft, when replacing the timing belt you should also replace the balanceshaft belt heres a diagram for both of them good luck and hope this helps.35de2d2.gif9665995.gif

Posted on Aug 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

Dodge Ram 1500 put in timing chines and now it will not start. Why?


Did you time the chains correctly? That's critical - the cam sprocket and the crank sprocket MUST be in a certain position when you put the chain on or the engine WILL NOT run.

Aug 02, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

I put new timing chain and gears on dodge d 50 2.6 and have no compression


you have the engine out of timing. take the timing belt off and roll the engine untill the number one cylinder is at top dead center (tdc) and then set your camshaft to where the intake valve is open on the number one cylinder. after that take the timing belt and put it on and your engine should run good.

Feb 02, 2013 | 1989 Dodge Ram 50

1 Answer

1990 Dodge Ram 50 not making power.


Timing! Timing chain? Check both!

Jan 23, 2013 | 1990 Dodge Ram 50

1 Answer

Timing marks dodge 2.6


Click here to see timing chain repair guide.

Dec 11, 2012 | 1988 Dodge Ram 50

1 Answer

I have a 1987 Dodge Ram 50 sport 2.6 litre the head gasket is blown how do i get the timing chain off to replace the gasket


You have to remove the oil pan - harmonic balancer - timing cover to replace timing chain... to replace cylinder head gasket and not the chain -- you need an assistant to hold the camshaft gear with chain on it. Suspending it with wire to keep the chain from moving the timing (do not let the chain relax as it will come off the crankshaft gear and change the timing)

Dec 04, 2009 | 1987 Dodge Ram 50

1 Answer

I have a 1984 dodge ram pick up with the mitsubishi motor and i was woindering if the timeing was belt or chain


1984 years came with the 2.0L, 2.6L gasoline and 2.3 diesel engines.

It's most likely a timing belt, but read further for more info. Recommended to be replaced at 60,000 miles (96,000 km) on gasoline engines and on diesel engines at 50,000 miles (80,000 km).

The 2.0 L Engine have two timing belts. One connects the crankshaft and camshaft, the second one drives the right silent shaft.

The 2.6L engine has a timing chain and a silent shaft chain.

Please check to see which particular engine you have and refer to the above for your answer.

Jun 29, 2009 | 1984 Dodge Ram 50

1 Answer

Put new oilpump and hadto remove timeing belt and gears. i need t


For the 1986 Dodge Ram 50 2.0L AND 2.6L 4-Cylinders:

Firing Order:
1-3-4-2

Cylinders:
(back)
...4
...3
...2
...1
(front)

Distributor:
.(back)
3.......4
1.......2
.(front)

For the Timing Marks: Click on the following Link. It has the Position of the Cranshaft and Camshaft and their respective marks.

http://www.2carpros.com/car_repair_information/year/1986/make/dodge/model/ram_50/1986_dodge_ram_50_timing_belt_diagram_marks.htm

Jan 02, 2009 | 1986 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...