Question about 2002 Chrysler Town & Country

Open Question

HOW DO YOU REPLACE THE SPEED SENSOR OF A 2002 CHRYSLER TOWN AND COUNTRY

I HAVE THE PARTS. IS IT EASY TO GET TO OR SHOULD I JUST TAKE IT TO A MECHANIC

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
short shadey
  • 421 Answers

SOURCE: location of the speed sensor on 1996 town & country

they are on the front drivers side of the transmisson and have two wires coming off them, there are two one is an input shaft sensor and the other is an output shaft sensor unless you have a 4 cyl van then there is only one sensor please rate -jeff

Posted on Sep 04, 2008

Ad
  • 76 Answers

SOURCE: 2002 Chrysler Town and Country

Ok, i'm assuming your replacing them, there is an oval rubber stopper on the backside of the rotor, in the backing plate, located near the bottom. it will tighten or loosen the e-brake shoes inside the rotor, loosen them all the way off, then get a big hammer and give them a really good smack, be carefull not to damage the wheel studs, if your reusing them hit on the hat of the rotor, if replacing you can hit right on the rotor face.
Use some antiseize on the hub before installin your new rotors, and don't forget to readjust your
e-brake and reinstall the rubber plug

Posted on Nov 18, 2008

chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

  • 323 Answers

SOURCE: locassion of output speed sensor on 2003 Town and Country

The input and output speed sensors look identical on the connector side. The one over the solenoid pack is the input, the one closer to the left frame rail or left front wheel is the output sensor. I hope this helps.

Posted on Apr 26, 2009

keemo68
  • 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the speed sending unit located on a chrysler town and country


transaxle has two speed sensors input speed sensor located behind transaxle cooler lines the output sensor located far right transmission case driver side.

Jan 04, 2013 | 2002 Chrysler Town & Country

2 Answers

What controls the odometer on a 2002 Town and Country


most likely the instrument cluster. you can bring the vehicle into any chrysler dealer and have them run tests on it.

Oct 18, 2012 | 2002 Chrysler Town & Country

2 Answers

Speedometer not working


normally read off your rear wheel abs sensor

Jan 14, 2009 | 2002 Chrysler Town & Country

2 Answers

2002 chrysler town and country wont leave limp mode


try getting a new shift solenoid for it. i had the same problem on my 2002 chrysler town and country and my plymouth breeze which is also a dodge product. it is very simple to do and doesnt take all that long. the part will probably run you about 150 to 200 dollars but it should fix your problem.

Dec 31, 2008 | 2002 Chrysler Town & Country

6 Answers

2002 chrysler mini van front end noisy .when you hit a bump.what


I had the same problem with my 2002 Town and Country Limited. I took it to the mechanic and had the sway bar links and ball joints replaced and still had the same clunking noise when going over bumps at low speeds. The van sounded great on the highway, but country roads were horrible. I was about to replace the struts and pay another 700 dollars when i read somewhere that the sway bar bushings could wear and cause the noise. I took it to the mechanic and he said absolutely not it would be a waste of money. Being the stubborn guy I am, I went to NAPA and bought the two bushings for 12 dollars and replaced them myself in an hour. I took the van for a test ride and the noise is completely gone. Please ignore your mechanic and replace the bushings ASAP! Pretty cheap try even if it doesn't work.

Nov 14, 2008 | 2002 Chrysler Town & Country

1 Answer

Transmission


you need to have the trouble codes read go to autozone they can read them for you and write them down and report back it is most likley a speed sensor on the transmission there is two of them and they are very cheap and easy to change called input /output speed sensors
1 05014469AA Wiring Repair Package, Input Speed Sensor
1 05014471AA Wiring Repair Package, Output Speed Sensor you dont need to use the wiring harness supllied with these sensors as they are for early model vans only please rate -jeff

Aug 23, 2008 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...