Question about 1999 GMC Jimmy

1 Answer

How to remove starter from engine? - 1999 GMC Jimmy

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 14,251 Answers

Click here to see guide to remove starter.

Posted on Dec 11, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove starter from 2004 pacifica


REMOVAL
Disconnect the negative battery cable.
Remove (UPPER RADIATOR CROSS MEMBER) and relocate (UPPER RADIATOR CROSS MEMBER REMOVED) the upper radiator crossmember, (Refer to 23 - BODY/EXTERIOR/RADIATOR CROSSMEMBER - REMOVAL).
Remove the radiator fan module (FAN MODULE IN VEHICLE) (Refer to 7 - COOLING/ENGINE/RADIATOR FAN - REMOVAL).
Remove the wiring harness clip from front mount.
Remove the coolant line clamp bolt (COOLANT LINE BRACKET).
Remove the upper nut from the front mount (FRONT RUBBER MOUNT UPPER NUT).
Remove the upper starter mounting bolt (UPPER STARTER BOLT).
Remove the middle starter bolt (MIDDLE STARTER BOLT).
Raise vehicle and support.
Remove the lower front mount nut (FRONT RUBBER MOUNT IN POSITION).
Raise and support engine (SUPPORT ENGINE).
Remove the lower bracket bolt to transmission (BRACKET TRANS BOLT).
Remove the lower bracket bolt to engine block (BRACKET ENGINE BLOCK BOLT).
Relocate the front mount and bracket.
Disconnect the positive battery cable from starter
Disconnect the solenoid connector from starter.
Remove the lower starter bolt (STARTER LOWER BOLT).
Remove starter from vehicle.

Aug 16, 2011 | 2004 Chrysler Pacifica

1 Answer

How do i connect my starter to the battery


REMOVAL & INSTALLATION 2.2L (VIN 4) Engine Fig. 1: Removal and installation of the starter — 2.2L engine shown 87952039.gif
Fig. 2: Remove the starter electrical connections from the back of the starter 91142p05.jpg
Fig. 3: Remove the three bell-housing cover retaining bolts and . . . 91142p06.jpg
Fig. 4: . . . remove the bell-housing cover 91142p07.jpg
Fig. 5: Remove the starter support brace-to-engine bolt 91142p08.jpg
Fig. 6: The starter is retained by two bolts 91142p09.jpg
Fig. 7: Remove the bolts and . . . 91142p10.jpg
Fig. 8: . . . remove the starter from the engine 91142p11.jpg
Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside 91142p12.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter. To install:
  8. Transfer the starter support bracket to the new starter if the starter is being replaced.
  9. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  10. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  11. Install the bell-housing cover.
  12. Install the starter electrical connections on the back of the starter. Tighten the "S'' terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  13. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines 87952040.gif
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle. To install:
  9. Raise the starter to the vehicle, then attach the wiring.
  10. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  11. If moved, reposition the engine wiring harness.
  12. Carefully lower the vehicle.
  13. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  14. Fasten the air inlet duct to the throttle body.
  15. Connect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1996 Chevrolet Cavalier

1 Answer

How do i remove the starter?


Removal
1. Disconnect negative battery cable. Raise and support vehicle. As required, remove nuts from A/C
compressor, exhaust system and/or engine braces, adjacent to starter. On M/T models, remove bending
brace from around starter (if equipped). On all models, remove other items that may interfere with
removal of starter.
2. If necessary, remove nut from engine cross brace. Using pry bar between upper engine mount and engine,
pry rearward and support engine.
3. If necessary, remove oil filter, air induction tube and cooling fan. Remove flywheel inspection cover (if
equipped). Remove starter solenoid terminal "S" nut and battery cable nut. Separate wiring from starter.
Remove starter mounting bolts. Remove shims and note arrangement for reassembly. Remove starter.
Installation
Before installing starter onto engine, tighten inner solenoid terminal nuts to ensure they are secure in cap.
Starter failure may occur due to terminal or cap damage. Install starter and wiring. Ensure shims are installed in
original location.

Jun 25, 2010 | 1996 Buick Regal Olympic Gold

2 Answers

How to change a starter on a 4.3 gmc sonoma 1997


STARTER REPLACEMENT ( 1995-97 4.3L MODELS )

ad8746e.jpg

Fig.: The starter motor on later model 4.3L engines is retained by two long bolts
  1. Disconnect the negative battery cable.
  2. Raise and support the front of the truck safely using jackstands.
  3. If necessary for access, disconnect the front exhaust pipe.
  4. If equipped, remove the starter heat shield.
  5. On the 2.2L engine, remove the brace rod from the front of the engine and the bell housing.
  6. On 2.2L engines, remove the drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well.
  7. Disengage the wires from the starter solenoid.
  8. On the 2.2L engine, remove the attaching bracket-to-engine mount bolt.
  9. Remove the starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
  10. Carefully lower the starter and shims (if equipped) from the vehicle.
  11. If necessary, remove the bracket (2.2L engine) or the shield (4.3L engine) from the starter assembly.

To install:
  1. If removed, install the bracket or shield to the starter, as applicable. Tighten the bracket nuts to 97 inch lbs. (11 Nm) or the shield nuts to 106 inch lbs. (12 Nm).
  2. Carefully raise the starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
  3. On the 2.2L engine, loosely install the bracket-to-engine mount bolt.
  4. Install the remaining starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm).
  5. Engage the wiring to the solenoid as noted during removal.
  6. On the 2.2L engine, install the brace rod and tighten the retainers.
  7. If disconnected for access, install the front exhaust pipe and tighten the fasteners.
  8. If equipped, install the starter heat shield.
  9. On 2.2L engines, install the drivers side wheel.
  10. Remove the jackstands and carefully lower the truck.
  11. Connect the negative battery cable.

Hope this help (remember rated this help) Good luck.

May 11, 2010 | 1997 GMC Sonoma

1 Answer

How do I get to the starter on a 98 concorde



Removal & Installation

2.7L Engine
  1. Remove or disconnect the following:

    Negative battery cable from the remote ground post Battery feed and posi-lock connectors Nuts from the catalyst support bracket and mount Starter heat shield 3 starter-to-engine/transaxle bolts Starter by rotating it toward the engine and sliding it rearward between the catalyst and the engine mount

To install:
  1. Install or connect the following:

    Starter by sliding it forward between the catalyst and the engine mount and rotating it away from the engine Starter and torque the 3 starter-to-engine/transaxle bolts to 40 ft. lbs. (54 Nm) Starter heat shield Nuts to the catalyst support bracket and mount Positive battery cable and torque the nut to 89 inch lbs. (10 Nm) Posi-lock connectors Negative battery cable to the remote ground post

3.2L & 3.5L Engines
  1. Remove or disconnect the following:

    Negative battery cable from the remote ground post Starter-to-engine/transaxle nut and bolts Positive battery feed wire from the starter Starter and position it to gain access to the posi-lock connector
  2. Place a support under the engine and slightly relieve the pressure from the left engine mount.
  3. Remove the 3 left engine mount-to-engine bolts.
  4. Slightly, raise the engine to provide more room.
  5. Remove the starter by sliding it rearward between the catalyst and the engine mount.
  6. Remove the posi-lock connector.

    0996b43f80204958.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Removal and installation of the starter motor

To install:
  1. Install or connect the following:

    Posi-lock connector Starter by sliding it forward between the catalyst and the engine mount
  2. Slightly, lower the engine.

    3 left engine mount-to-engine bolts Positive battery feed wire to the starter and torque the nut to 89 inch lbs. (10 Nm) Starter and torque the starter-to-engine/transaxle bolts to 40 ft. lbs. (54 Nm) Negative battery cable to the remote ground post

Mar 23, 2010 | 1998 Chrysler Concorde

1 Answer

How do I remove the starter on a 1999 Dodge Intrepid


Removal & Installation
2.7L Engine

  1. Remove or disconnect the following:
    Negative battery cable from the remote ground post Battery feed and posi-lock connectors Nuts from the catalyst support bracket and mount Starter heat shield 3 starter-to-engine/transaxle bolts Starter by rotating it toward the engine and sliding it rearward between the catalyst and the engine mount

To install:
  1. Install or connect the following:
    Starter by sliding it forward between the catalyst and the engine mount and rotating it away from the engine Starter and torque the 3 starter-to-engine/transaxle bolts to 40 ft. lbs. (54 Nm) Starter heat shield Nuts to the catalyst support bracket and mount Positive battery cable and torque the nut to 89 inch lbs. (10 Nm) Posi-lock connectors Negative battery cable to the remote ground post

3.2L & 3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable from the remote ground post Starter-to-engine/transaxle nut and bolts Positive battery feed wire from the starter Starter and position it to gain access to the posi-lock connector
  2. Place a support under the engine and slightly relieve the pressure from the left engine mount.
  3. Remove the 3 left engine mount-to-engine bolts.
  4. Slightly, raise the engine to provide more room.
  5. Remove the starter by sliding it rearward between the catalyst and the engine mount.
  6. Remove the posi-lock connector.

    8df864a.jpg
    Fig. Removal and installation of the starter motor

To install:
  1. Install or connect the following:
    Posi-lock connector Starter by sliding it forward between the catalyst and the engine mount
  2. Slightly, lower the engine.
    3 left engine mount-to-engine bolts Positive battery feed wire to the starter and torque the nut to 89 inch lbs. (10 Nm) Starter and torque the starter-to-engine/transaxle bolts to 40 ft. lbs. (54 Nm) Negative battery cable to the remote ground post
Hope this help (remember rated and comment).

Mar 22, 2010 | 1999 Dodge Intrepid

2 Answers

Where is the starter on a 1998 cavalier z24


1998 Chevrolet Cavalier 2.4L SFI DOHC 4cyl - Repair Guide
Look at the the lower end of the engine behind the radiator.

REMOVAL & INSTALLATION

2.2L (VIN 4) Engine

b30d4a5.jpg

Fig. 1: Removal and installation of the starter-2.2L engine shown

ce77b94.jpg

Fig. 2: Remove the starter electrical connections from the back of the starter

a7d8ae8.jpg

Fig. 3: Remove the three bell-housing cover retaining bolts and ...

3580a66.jpg

Fig. 4: ... remove the bell-housing cover

95f5421.jpg

Fig. 5: Remove the starter support brace-to-engine bolt

225716e.jpg

Fig. 6: The starter is retained by two bolts

51b21e5.jpg

Fig. 7: Remove the bolts and ...

35a623c.jpg

Fig. 8: ... remove the starter from the engine

3658d11.jpg

Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter.
To install:
  1. Transfer the starter support bracket to the new starter if the starter is being replaced.
  2. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  4. Install the bell-housing cover.
  5. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  6. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines

7ac0166.jpg

Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable accese to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle.
To install:
  1. Raise the starter to the vehicle, then attach the wiring.
  2. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  3. If moved, reposition the engine wiring harness.
  4. Carefully lower the vehicle.
  5. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  6. Fasten the air inlet duct to the throttle body.
  7. Connect the negative battery cable.

I hope help you with this (remember rated this help) Good luck.

Oct 12, 2009 | 1998 Chevrolet Cavalier

1 Answer

Need to replace starter


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect battery negative remote cable from remote ground post.
  3. Raise and safely support the vehicle
Starter Motor

098a02a.gif
    1. Remove or disconnect the following:
    2. Three bolts attaching starter to engine
    • Positive battery cable from starter
    • Starter assembly from transmission housing
    1. Position jack stand beneath engine and slightly lift to relieve pressure from left engine mount.
    2. Remove three left engine mount bolts from engine block.
    3. Jack engine up slightly to give more room to maneuver starter assembly.
    4. Slide rear of starter motor out between catalytic converter and engine mount.
    1. Remove or disconnect the following:
    2. Posi-lock starter solenoid connector.
    • Starter from vehicle.
    To Install:
    1. Install or connect the following:
      • Positive battery cable to starter
      • Posi-lock starter solenoid connector
    2. Jack engine up slightly to give more room to maneuver starter assembly.
    3. Install or connect the following:
      • Starter
        1. Torque to 40 ft. lbs. (54 Nm)
      • Three left engine mount mounting bolts to engine block
    4. Lower vehicle.
    5. Connect the battery negative cable.
  • May 05, 2009 | 1998 Chrysler Concorde

    1 Answer

    Where is the starter located on a 2000 Cabrio?


    disconnect ground cable make sure the radio is turn off so you wont lose code.raise support front of car.you need a floor jack.for A3 engine.place a piece of wood on floor jack saddle .place floor jack under the engine oil pan.slightly raise engine just a little bit to take load off engine mount.the starter and engine uses same bolts removes bolts .remove starter label wires remove postive battery cable.from starter .the 010 transaxle engines remove bracket that support starter to engine remove starter bolts support starter then remove it.on vechicle with manual transmission the bushing where starter fits into bell housing should be replaced besure to get a bushing removing tool.

    Mar 22, 2009 | 2000 Volkswagen Cabrio

    Not finding what you are looking for?
    1999 GMC Jimmy Logo

    Related Topics:

    16 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...