Question about 2000 Ford Focus

Open Question

How to replace intake manifold runner control mrc actuator 2007 ford focus

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

66 chrgr
  • 1011 Answers

SOURCE: INTAKE MANIFOLD CONTRL RUNNER VAVLE LOCATIONS

they are on the back side of the motor just above the transmission .take off the dog house and you will see the unit.

Posted on Jan 25, 2009

daves944
  • 1050 Answers

SOURCE: I have a '96 Ford Windstar 3.8L & getting OBDII P1537 code.

A common problem on Windstars, there are two IMRC valves, the only way to fix them is replacement, which is not that hard. They are mounted on the end of the intake manifold and control runner length. There is a front and rear one, I'm not sure which one this is but you'll probably have to go to Ford to buy it and they should be able to tell you with the code number. The problem will not affect driveability that much, but if you have emissions testing at your location, this will likely cause it to fail.

Posted on Apr 05, 2009

  • 14036 Answers

SOURCE: 1998 ford windstar 3.8 with code p1538. Is this a

LOOKING IN CODE BOOK.POSSIBLE CAUSE TO YOUR PROBLEM THE IMRC COULD BE STUCK OPEN.OR THE IMRC ACTUATOR IS DAMAGED OR HAS FAILED.ALSO THE IMRC MONITOR SIGNAL CIRCUIT COULD BE SHORTED TO POWER GROUND OR SHORTED TO SIGNAL GROUND RETURN.

Posted on Oct 23, 2009

SOURCE: Intake manifold runner control stuck open

Forget that Dealer. They do not want your business because, they are capable of repairing both your vehicles. You need to find a good repair facility near your home, before you need one. Should have done that before dealer warrantee was up. You can't solve theses issues unless your a knowledgable auto technician. Do not drive any of todays vehicles with check engine lights etc on dash and all the other issues you have. Everyone is trying to save money hoping things go away. We no longer live in the 1960's. Theses are expensive cars to buy and maintain. There are very few so called auto mechanics with even basic electrical knowledge to even attempt to solve todays technology on a vehicle and no training avail for them. Did you drive the vehicle with a tech riding with you? Did they drive it with you riding in it? Was it acting up when you took it in? Forget the service writer at the dealership and get the person who has the task and knowledge of your veh systems. If they don't mention a road test with you present, they have no intention of finding your problems. I used to own a Trans Repair Shop. You got drilled for a half hour and I needed a years history on the vehicle or I turned the job away. Also I was very clear on the costs involved as well as the % of even finding an issue.

Posted on Feb 06, 2010

honeymokey
  • 3113 Answers

SOURCE: ford focus p2008 engine code??

Check pcv hose from the manifold to pipe. It will get soft and collapse, leak. It will turn light on. Check while running.

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford focus 2.3 litre DTC P2004 intake manifold runner control stuck open. What does it mean when it says shorted to VREF or signal circuit shorted open or shorted to VPWR.


code p 2004 refers to intake manifold air control actuator bank 1--actuator stuck open===causes --wiring--intake manifold air control actuator---mechanical fault
it also refers to intake manifold air control solenoid bank 1--solenoid stuck open=== causes --wiring---intake manifold air control solenoid---mechanical fault
reference auto data technical fault codes
I cannot find reference to the VREF or VPWR as they may be referenced in a ford workshop manual so you may have to ask a ford service person what they stand for but I suspect that they will come back to the same thing as listed in the causes

Feb 19, 2016 | Ford Cars & Trucks

2 Answers

2008 dodge avenger code p2004


Intake Manifold runner control stuck open - bank one:
- Intake Manifold Runner Binding Or Sticking
- Faulty Manifold flow valve
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection

There is a factory service bulletin for this problem for 2007-2008 Dodge Avengers. (JS)

Sep 22, 2015 | Dodge Cars & Trucks

1 Answer

How to fix code p2004 on 2005 ford focus


you code is here

P2004 Ford Intake Manifold Runner Control Stuck Open Bank 1


Possible causes - Intake Manifold Runner Control (IMRC) monitor signal shorted to power
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Intake Manifold Runner Control (IMRC) solenoid
- Damage Powertrain Control Module (PCM)
- Blocked vacuum hoses
alt="What does this mean?"> What does this mean? Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P2004 Ford Description The P2004 is set when the Intake Manifold Runner Control (IMRC) is commanded closed by the Powertrain Control Module (PCM), but the IMRC indicates open.


Read more: http://engine-codes.com/p2004_ford.html#ixzz3lke1SreV

Sep 14, 2015 | Ford Cars & Trucks

1 Answer

2004 ford f 150 5.4 3V pulled intake fixed vac hose came off replaced imrc & still show intake runner control closed bank 1 Still has no power when I get in it to pass something any ideas?


Is your check engine light on ? Any codes ?

There are three basic types of intake air sub-systems:


  • Intake Manifold Runner Control (IMRC) electric actuated system

  • Intake Manifold Swirl Control (IMSC) vacuum actuated system

  • Intake Manifold Tuning Valve (IMTV)

These subsystems are used to provide increased intake airflow to improve torque, emissions and performance. The overall quantity of air metered to the engine is controlled by the throttle body.

Intake Manifold Runner Control (IMRC) Electric Actuated System
The Intake Manifold Runner Control (IMRC) Electric Actuated system (Figure 107) consists of a remote mounted motorized actuator with an attaching cable for each housing on each bank. Some applications will use one cable for both banks. The cable or linkage attaches to the housing butterfly plate levers. The 2.0L (2V) Focus IMRC uses a motorized actuator mounted directly to a single housing without the use of a cable. Each IMRC housing is an aluminum casting with two intake air passages for each cylinder. One passage is always open and the other is opened and closed with a butterfly valve plate. The housing uses a return spring to hold the butterfly valve plates closed. The motorized actuator houses an internal switch or switches, depending on the application, to provide feedback to the PCM indicating cable and butterfly valve plate position.



Below approximately 3000 rpm, the motorized actuator will not be energized. This will allow the cable to fully extend and the butterfly valve plates to remain closed. Above approximately 3000 rpm, the motorized actuator will be energized. The attaching cable will pull the butterfly valve plates into the open position. Some vehicles will activate the IMRC near 1500 rpm.



WARNING: SUBSTANTIAL OPENING AND CLOSING TORQUE IS APPLIED BY THIS SYSTEM. TO PREVENT INJURY, BE CAREFUL TO KEEP FINGERS AWAY FROM LEVER MECHANISMS WHEN ACTUATED.




  1. The PCM uses the TP sensor and CKP signals to determine activation of the IMRC system. There must be a positive change in voltage from the TP sensor along with the increase in rpm to open the valve plates.




  1. The PCM uses the information from the input signals to control the IMRC motorized actuator based upon rpm and changes in throttle position.




  1. The PCM energizes the actuator to pull the butterfly plates open with the cable(s) or linkage.




  1. The IMRC housing contains butterfly plates to allow increased air flow.

Jun 29, 2015 | Ford Cars & Trucks

1 Answer

Where is the intake manifold runner control on a 2007 ford focus


07 focus ,which engine?
alldata.com its there.
login .

May 13, 2014 | Cars & Trucks

1 Answer

Chhrysler sebring 2007 2.4 litter getting code p2004 intak manifold runner control how do you fix it


code p2004 refers to intake manifold air control actuator bank 1---actuator stuck open===causes --wiring--intake manifold air control actuator --mechanical fault.
also refers to intake manifold air control solenoid bank 1 solenoid stuck open===causes--wiring intake manifold air control solenoid --- mechanical fault
you may be able to remove and clean the units to ensure they move freely otherwise replace them

Dec 31, 2013 | Cars & Trucks

1 Answer

Ford F140 4.2 Do Engine codes P0305, P0306, and P1518 relate to each other


I am assuming you mean F150 truck.
The answer is maybe.
Code 305 and 306 are missfire codes for cylinders 5 and 6.
Code 1518 is for a problem with the intake manifold runner control which could cause the other two codes.

P1518 FORD Description The Intake Manifold Runner Control (IMRC) is monitored for failure during continuous or key ON engine OFF self-test.
Possible causes - Intake Manifold Runner Control (IMRC) harness is open or shorted
- Intake Manifold Runner Control (IMRC) circuit poor electrical connection
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Engine Control Module (ECM)
Read more: http://engine-codes.com/p1518_ford.html#ixzz2KSN6Thui

Feb 10, 2013 | Ford Cars & Trucks

1 Answer

P2004 intake man.control bank 1 stuck open


The intake manifold runner control (IMRC) cables have plastic ends that like to break. Check your IMRC to see if the cable it attached. If the cable s attached, then the IMRC actuator is probably defective. (see diagram)

6_17_2012_2_48_42_pm.gif

Jun 17, 2012 | 2003 Ford Focus

1 Answer

P1537 how do I fix this problem?


CODE P1537 - INTAKE MANIFOLD RUNNER CONTROL MALFUNCTION BANK 1 STUCK OPEN. POSSIBLE CAUSES. IMRC MONITOR SIGNAL CIRCUIT SHORTED TO POWER GROUND. IMRC MONITOR SIGNAL CIRCUIT SHORTED TO SIGNAL GROUND RETURN. IMRC ACTUATOR IS DAMAGED OR THE PCM HAS FAILED. - IMRC - IS INTAKE MANIFOLD RUNNER CONTROL.

Sep 01, 2011 | 1998 Ford Windstar

1 Answer

Location of IMRC ford focus


I am assuming you have a SPI motor. If so the IMRC(intake manifold runner control) is located on the drivers side if the intake manifold. It is an electromechanical actuator square/ rectangular and has an electrical connector on it.

Apr 03, 2010 | 2000 Ford Focus

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...