Question about 1999 Jeep Grand Cherokee

1 Answer

P0743 p0753 p0748

Jeep Laredo throwing these codes. p0743 p0753 p0748 Before replacing the transmission, I'd like to know if there are any other possible repairs i might try. Thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Filmmaker:

    Uploaded 5 video answers.

  • Expert
  • 141 Answers

When diagnosing multiple fault codes it can be tricky figuring out whats going on for instance all three of the codes you have are an electrical nature and not mechanical faults in the transmission most likely they share a common power or ground circuit and have lost one or the other also if they do share any circuit and anyone of these are faulty it would generate the other codes. to do an accurate circuit check you should remove the transmission pan so you can check the terminals at the solenoids and switches on the valvebody because the problem could be in the "passthrough" connector

Posted on Dec 11, 2012

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: jeep codes location of unit

Got me a complete manual for 199 jeep factory model and found location of each individual unit in question. Manual gives u possible solution to each code and repair and or replace. As a mechanic myself testing, trouble shooting and repair was not that difficult. Shift solenoid was very difficult to get to. Located under the head lamp passenger side.

Posted on Nov 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 dodge Dakota transmission code P0753 and P0743 indicate


P0743 torque convirtor circuit malfunction
P0753 3-4 shift solonoid

Apr 07, 2017 | 1998 Dodge Dakota

2 Answers

I drained the transmission fluid put of my Jeep. I got taken away from it for about 4 days before I could get back to it. I have added fluid back in slowly.


Sounds like maybe the filter isn't seated in the seal or the seal is missing/broken and sucking air into the pump, this would cause bubbles, one way to tell for sure is to overfill the transmission by a couple quarts for testing and see if the bubbles go away.

Jan 03, 2016 | Jeep Cars & Trucks

2 Answers

These error code's were read: p0700, p0765, p0760, p0755, p0743. How can we fix this? Can it be the harness connection?


How To Fix Transmission A4CF2 Shift Problems / Check ...

? 18:46
https://www.youtube.com/watch?v=URUT3t8uUCw
Oct 27, 2014 - Uploaded by ProProjects
Thanks to ProProjects P0700 P0743 Torque Converter Clutch Circuit Electrical. ... P0765 - Shift Control Solenoid Valve D (Overdrive Solenoid) ... I have only two codes P0760 P0755 but my car is a mitsubishi galant 2.4 liters.

PDF]Technical Service Bulletin - RevBase

www.revbase.com/BBBMotor/Tsb//DownloadPdf?id=133873
Diagnostic Trouble Codes P0740, P0741, P0742, P0743, P0746, P0748, P0750,.P0755, P0760, P0765 or P0770 set ... P0700 - TCM MIL request signal.

Nov 07, 2015 | Cars & Trucks

1 Answer

Code p1529 kia spectra


I suggest you take that up with the person that installed the transmission. They should be able to reset codes that were triggered when installing trans

Jan 03, 2014 | Cars & Trucks

1 Answer

Mers. E320 1997 i got those codes P0743, P0753, P0763 and P0758


This is a wiring problem you have a loose connector at the ECT control module or connector at the transmission,the solution is make proper connection and this is a common problem,that or you have a bad conductor plate in the transmission. Go to the right rear of the engine compartment ensure you connection for the transmission module is all hook up, go to the transmission and ensure nothing at the harness is disconnected

Mar 29, 2012 | Cars & Trucks

1 Answer

Code p0753 for a dodge ram 2500 360 m


Both fault codes refer at Tnasmission problem...

P0743 - Torque Converter Circuit Electrical
This DTC appears when an open or shorted condition is detected in the TCC (Torque Converter Clutch) solenoid control circuit; check this as possible causes:
- fused ignition switch output circuit open
- torque converter clutch solenoid defective
- TCC solenoid circuit w/h intermittent defect
- TCCsolenoid circuit w/h observable defect
- TCC solenoid control circuit open
- TCC solenoid control circuit short to ground
- PCM defective (TCC solenoid control circuit)

You will need remove the cover/pan to inspect the harness that goes to all the solonoids and then to inspect the valvebody and the TCC solonoid itself. If you have a multimeter then you could ohm through the harness and even the solonoid. I have found that most of the time this code was produced because of the solonoid itself. But it could be the circuits to it also. There is abig connector an top of the trans that goes into the trans and the internal harness ispect that connector for any corrosion or damaged pins or wires.


P0753 - Shift Solenoid A Electrical Malfunction
This is a common repair that I have replaced several of the solenoid but it is not a cronic problem. It be the wire going to the solenoid shorted so make sure that is check before the transmission is tilted down and the side cover removed. 90% it is just the solenoid; the solenoid is located in the side pan of the tranmission. It would mean lowering the cradle(what the engine and transmission sit on) and lowering the transmission down about one to two feet. Check this like a possible cause:
- 1-2 shift solenoid control circuit is open or shorted to ground
- 1-2 shift solenoid control circuit is shorted to voltage
- 1-2 shift solenoid has failed
- PCM has failed

You will need to remove the transmission pan and its the solenoid with the red and light green wires going to it. Let us know if you have questions contact us here.

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using FixYa.

Jose.






Oct 20, 2011 | 1997 Dodge Ram 2500 Club Cab

1 Answer

Jeep codes location of unit


Got me a complete manual for 199 jeep factory model and found location of each individual unit in question. Manual gives u possible solution to each code and repair and or replace. As a mechanic myself testing, trouble shooting and repair was not that difficult. Shift solenoid was very difficult to get to. Located under the head lamp passenger side.

Nov 19, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

1,003 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...