Question about 2005 Chrysler Pacifica

Open Question

Where is a tcm on a 2005 chrysler pacifica

Car wont accelerate pass 40 mph at times

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: Set clock

Beside the analog clock display there is a small dot where you can insert a pen. When you push this in gently the clock starts moving very fast. Hold this button in until the time is correct. Make sure you stop before you go by the time you want because it only goes in one direction

Posted on Dec 18, 2008

Ad
MrScary66613
  • 1990 Answers

SOURCE: I need to replace the thermostat for a 2005 chrysler pacifica

Follow the Upper Radiator Hose to the Block. There is a Bell housing there that the Hose Connects to. Remove that Bellhousing and the Thermostat is Right Under it.

Posted on Jan 15, 2009

  • 2 Answers

SOURCE: Where are the spark plugs located in a 2005 Chrysler Pacifica?

Jay from Ma,
You have it backwards the rear three are accessable with the front three being under the intake. To remove the intake simply remove throttle body and aproxamently 15 other bolts.

Posted on May 08, 2009

  • 4 Answers

SOURCE: 2006 Chrysler Pacifica Auotmatic Liftgate

Yes new gas shocks on the lift gate will fix your problem. I had the same problem on my 2005 Pacifica and when it hit my head- I came up with the solution.

Good Luck,
Ray

Posted on May 11, 2009

turo1000
  • 18 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Posted on May 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Transmission Control Module located on the 2005 Chrysler Pacifica


Typcially, is these mini-vans it is on the rightside (interior) wing panel, the ECU is on the leftside wing panel. If you start at the torque converter solenoid and trace the wiring loom it leads straight to the TCM.

Aug 03, 2017 | 2005 Chrysler Pacifica

2 Answers

Why does my 07 Chrysler Pacifica feel like its going to vibrate off the road with acceleration at 40 - 60 Mph?


2007 Chrysler Pacifica Problems, Defects & Complaints

www.carcomplaints.com/Chrysler/Pacifica/2007/
5 days ago - The 2007 Chrysler Pacifica has 97 problems & defects reported by Pacifica owners. The worst complaints are engine, transmission, and ...‎Engine - ‎TSBs 13 - ‎Crash Tests 2 - ‎Defect Investigations 2

Aug 03, 2015 | 2007 Chrysler Pacifica Touring

1 Answer

After changing the water pump and timing belt on a 2005 Chrysler Pacifica 3.5 the engine will idle but surges when I accelerate. There is no codes being shown.


i'd advise rechecking the timing belt positioning again , surging can be a symptom of timing being out and i would'nt expect any codes if its the belt timing, as is set up manually and not monitored by the PCM

Jun 11, 2015 | 2005 Chrysler Pacifica

1 Answer

I have a 2005 chrysler pacifica it had been coded for the doors to lock at 15 mph but no longer does this please help


Car on, hit menu button then when you get to automatic door lock hit
step or reset till it says yes

Mar 24, 2014 | 2005 Chrysler Pacifica

1 Answer

05 Pacifica stumbles during acceleration


check the manifold is not leaking on the intake side. also check and clean the intake top. carb clean helps to clean out all the muck out on to a cloth. also carb cleaner will help if you have a leak spray round the intake when engine is a temp. engine will cut out or speed up depending on carb cleaner used. were there is a leak.

Jan 19, 2014 | Chrysler Pacifica Cars & Trucks

2 Answers

Car cuts off when putting it in reverse, chrysler pacifica 2005


Check the engine mounts for being broken and the wiring around the engine for chaffing and the ground cables.

Nov 24, 2012 | 2006 Chrysler Pacifica

3 Answers

2005 Pacifica Accelerator Sticks


Have the same vehicle, a 2005 Chrysler Pacifica. Also have the same problem w/ the sticking accelerator. I dope it up real good w/ WD-40 and axle grease. It works for a few days, then goes back to sticking. Drove over my $250 chainsaw the other day, wiping out the cutting bar on the saw. When the boys in DC get off Toyota's case I hope they open an investigation on this defect.

Jan 27, 2010 | 2005 Chrysler Pacifica

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...