Question about 2006 Ford F-150

1 Answer

How to replace a headlight bulb on 2006 f 150

I need to replace a bulb on head lamp on truck ford f 150 2006 thanks for your help!!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

They are replaced from inside the engine compartment at the rear of the headlight bazals. if it's the side the battery is on you will likely have to remove it first.

Robert

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Relace Headlight Bulb


Hope this helps and please don't forget to rate! Thanks!


Removal & Installation
  1. Disconnect battery cable.
  2. Remove the head lamp bolts.
  3. Disconnect the head lamp connector.
  4. Remove the head lamp.
  5. Installation is the reverse order of removal procedure.


c17hydro_146.gif

Headlight bulbs-2000-2005 Accent

Jan 23, 2011 | 2001 Hyundai Accent

1 Answer

Removal of head light assy 1989 ford ranger.


Hello,

To remove the front head light please follow the steps below:
  1. Place the Ford Ranger in "Park." Turn the engine off. Turn the headlights off. Remove the key from the ignition. Allow the truck to cool for about 20 minutes.
  2. Open the hood of the vehicle. Locate the two retainer pins on the headlight assembly of the light that needs to be replaced. Pry the retainer pins open with your finger. This releases the headlight assembly from the Ranger.
  3. Pull the headlight assembly forward. Unplug the electrical connector from the back of the assembly by hand. Rotate the retaining ring counterclockwise and slide it off the plastic bulb base.
  4. Pull the burned out bulb straight out of the headlight assembly. Discard the used bulb. Insert a replacement bulb into the headlight assembly and push it straight into the socket until it clicks into place. Slide the retaining ring around the bulb and rotate it clockwise to secure it.
  5. Plug the electrical connector into the back of the unit. Slide the headlight assembly back into the Ranger. Push the retaining pins back down to secure the headlight assembly.
Hope this helped. thank You for using FixYa!!!

Jan 19, 2011 | 1989 Ford Ranger

1 Answer

Replace head light bulb


I have a 2001 Windstar and can help you with your question. The headlight lamp is easy to replace. Open the hood and reach behind the headlight assembly. Carefully grasp the lamp and turn it counter clockwise. Once the lamp is out, remove the wire pigtail. Replace the lamp and reinstall. A real easy fix.

Jan 09, 2011 | 2000 Ford Windstar

1 Answer

How do I replace the front left (driver side) headlight? I have removed the cap and the electrical, but can't figure out how to remove the bulb so I can put a new one in. Your help is appreciated.


Removal & Installation
  1. Disconnect the negative battery terminal.

  2. Remove the head lamp mounting bolts, then disconnect the lamp connectors.

  3. Replace the head lamp bulb(A), position bulb(B) and turn signal bulbs(C).
    41311_tucs_g0048.gif

    Head lamp bulb(A), position bulb(B) and turn signal bulbs(C)

  4. To install, reverse removal procedure.

Dec 12, 2010 | 2005 Hyundai Tucson

1 Answer

I have a 2008 Ford Fusion and the passenger side head lamp will not come on. The fog lights and driver side head lamp works but the passenger side will not work on bright or on dim, what could this be?


Hi. Since the headlight on the driver side is working then we dont have any problem with the fuse or relay. Check the wiring and the socket of the passenger headlight if it is intact to the bulb. If it is intact, then this could be a headlight problem. Time to replace the passenger headlight.

Sep 06, 2010 | 2008 Ford Fusion

2 Answers

How to get headlamp out from ford fiesta 03


If you're just replacing the bulb, you access it from the rear of the headlight assembly. Just sqeeze the nylon locking device, and turn it counter clock wise, then pull the bulb out, and replace.

Dec 27, 2009 | 2000 Ford Focus

2 Answers

How to replace headlights bulbs in a grand cherokee 2001


  1. Remove the jack screw attaching the top of the head lamp to the head lamp mounting module.
  2. Grasp the upper inboard and lower outboard corners of the head lamp and pull the head lamp outward.
  3. Remove the bad bulb socket from the head lamp module and remove bulb from socket.
  4. Install new bulb into socket and reinstall socket into head lamp module.
  5. Position the head lamp on the vehicle and align the ball studs with the sockets.
  6. Push the head lamp inward to secure the ball studs with the sockets.
  7. Install the jack screw attaching the top of head lamp to the head lamp mounting module.
Do not touch glass of halogen bulbs at the oil can cause the headlight to blow out

Nov 12, 2009 | 2001 Jeep Grand Cherokee

1 Answer

How do you remove the head lamp assembly on a 1993


1. Make sure headlamp is off and open hood.
2. Taurus model years 1990-1999: you must remove the whole headlamp to replace the bulb. Not a horrible task. Just annoying.
3. Facing the driver's side headlamp, and looking at the headlamp itself, at clock positions 8, 11 and 1 are the headlight housing screws. They all look the same. Using a 10mm socket wrench, remove these 3 screws and set them aside.
4. Just to the right of the "11 o'clock" housing screw is a bolt (same hexagonal 10mm sized top as the housing screws). This just needs a few turns to loosen it.
5. Gently pull the whole headlight forward. Now you can get at the bulb.
6. Disconnect the electrical connector from the bulb. Now the headlamp is free to work with. Remove the bulb, replace with a new bulb, make sure the bulb housing cylinder is in place and reconnect the electical.
7. Place headlamp back into position. Line up screw holes. Tighten the bolt. Replace housing screws and tighten.
8. Passenger side headlamp is mirror image of driver's side. Screws at 11, 1 and 4 o'clock positions. Bolt should be to the left of the "1 o'clock" housing screw.

Oct 12, 2009 | 1993 Ford Taurus

1 Answer

How do I get the head lamp assmebly out?


Generally, headlight bulbs turn counterclockwise. You may need to put a little extra force on it since the rubber may have siezed onto the assembly.

Aug 13, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
2006 Ford F-150 Logo

Related Topics:

906 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...