Question about Cars & Trucks

Open Question

Where can I find TTY Rod bolts for 4.0 SOHC Ford Engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

Ad
  • 334 Answers

SOURCE: Need confirmation that 5 Speed Transmission out 1993 Mazda Protege SOHC 1.8 liter Will Bolt up to the Same L-4 Block Engine /Mounts in the 1990 Mazda Protege LX 1.8 liter DOHC

try calling a junkyard and see if they will tell you the enterchange ok good luck

Posted on Apr 18, 2009

inspectmycar
  • 233 Answers

SOURCE: Needing engine bolt torque specifications for a

stage 1 tighten to 30 ft pounds
stage 2 tighten 90 degrees
stage 3 loosen one full turn
stage 4 tighten to 30 ft pounds
stage 5 tighten 90 degrees
stage 6 tighten 90 degrees
this is per mitchell on demand courtesy of ford specs on the lft and right head.
for some reason there are no torque specs on mitchell for connecting rods and mains.

Posted on Sep 16, 2009

johnjohn2
  • 5763 Answers

SOURCE: 93 ford aerostar 4.o engine head bolt torque

step one is 22 ft lbs.
step two is 52 ft lbs
step #3 is turn an additional 90 degrees. sart in the middle and work your way out going top tobottom, good luck.

Posted on Nov 03, 2009

Testimonial: "thanks very much. I thought that the "90 degrees" on the gasket instruction sheet was a misprint. Your answer was quick and informative. G.M."

  • 164 Answers

SOURCE: i have a 98 ford

will you be able to connect ALL the computer sensors to the OLDER engine and be Happy??/.

Posted on Mar 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'll pan torque spec on 2002 rord ranger 4.0 sohc


SOHC V6 Torque Specifications - Ford Explorer and Ranger Forums ...

https://www.explorerforum.com/forums/showthread.php?t=406687
Apr 25, 2014 - SOHC V6 Torque Specifications Under the Hood. ... related to the Ford SOHC V6 4.0L engine used in Explorers, Mountaineers, Mustangs and Rangers. .... Oilpan (sheet metal) to crankcase reinforcement section bolts: 80 lb-in (E/MWM) ....Ranger Mountaineer - Sport thru '03 - 2nd Generation, 2002 - 2005 ... Transmission pan drop
5 posts
May 7, 2012
SOHC V6 Timing Chain Inspection & Repair
19 posts
Aug 10, 2010
Another transmission won't go after fluid change
19 posts
Mar 14, 2009
Help with 4.0 SOHC timing
15 posts
Mar 12, 2006
More results from www.explorerforum.com

[PDF]SPECIFICATIONS > TORQUE SPECIFICATIONS

www.askatech.com/askatechlive/forums/resourcehandler.ashx?a=5581
Jan 6, 2014 - TORQUE SPECIFICATIONS ... ENGINE - 4.0L SOHC. 2002 FordExplorer Sport Trac 4.0L Eng. (1). (2) ... Oil Pan Ladder Frame Bolts (Inside).

Torque Specifications - AutoZone


Jan 04, 2016 | Cars & Trucks

1 Answer

Head bolt sequence and torque values on a 1999 Chevy 3.1L engine


if the 8th number om your VIN is a "J" then this is the correct prossess 3.1LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.

if the 8th number on your VIN is a "M" then this is the correct prossess 3.8LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.

Oct 12, 2011 | 1999 Chevrolet Malibu

1 Answer

I have a 98 ford explorer with a 4.0 sohc engine can i replace it with a 4.0 push rod engine


will you be able to connect ALL the computer sensors to the OLDER engine and be Happy??/.

Mar 20, 2011 | Ford Explorer Cars & Trucks

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

2 Answers

Torque settings for a hyundai accent 1500 1998 model torque settings for head , conrods and crank


cylinder head bolt torque

52-55 ft lbs. cold engine
59-63 ft lbs. hot engine

connecting rod cap nut 26-28 ft lbs. SOHC
connecting rod cap nut 23-26 ft lbs. DOHC

main caps 41-44 ft lbs.

Dec 19, 2010 | Hyundai Motor 1998 Accent

1 Answer

I am looking 4 the torque pressures (ft.lbs) on the main crank bearings, and rod bearings on a 2007 Ford 5.4 3 valve engine??? Gerry..............thank-you


mains - vertical bolts first 30 ft.lb. PLUS 90 degrees
pattern frt

8 7
4 3
2 1
6 5
10 9
side bolts
22 ft. lb plus 90 degrees
pattern frt

7 8
3 4
1 2
5 6
9 10

connecting rod caps cracked type rod-rod and caps must be kept in matched sets, recommend new bolts/nuts, spec is 32 ft lb. plus 105 degrees - torque each item to the correct torque then go back and do the degrees. these are torque to yield bolts and the procedure is very important.

Oct 02, 2010 | Ford F-150 Cars & Trucks

3 Answers

Timing belt diagram for a 1999 ford escort 2.0


Hope this helps you, you also might want to replace the water pump, due to it's timing belt driven.

29c5183.gif

Sep 24, 2010 | Ford Escort Cars & Trucks

1 Answer

I need torque specs for the head bolts on a 2004 Dodge Stratus Coupe 2.4L SOHC


For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Aug 02, 2010 | 2004 Dodge Stratus

1 Answer

Torque setting for intake manifold, head bolt and exhaust manifold1992 ford explorer


what engine do you have? the 4.0l push rod engine = in/manifold 15-18ft-lb, cyl.head bolts=stp1:44ft-lb stp2: 59ft-lb,stp3: + 90 degrees, ex/manifold = 15-18 ft-lb. the 4.0l sohc.engine = in/manifold107-123 in-lb,cyl.head bolt 8mm=23-25ft-lb,12mm=26 ft-lb+90 degrees+90 degrees,ex/manifold= 15-18 ft-lb. and the 5.0l =in/manifold=24ft-lb,cyl.head=stp1:30ft-lb stp2: 50ftlb,stp3: +90 degrees, ex/manifold=30 ft-lb

Oct 09, 2009 | 1992 Ford Explorer

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...