Question about Cars & Trucks

Open Question

Jetta 1999 has check engine light and code p0341

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

j_del
  • 1586 Answers

SOURCE: 1999 vw jetta 2.0

Sounds like two problems. P0300 and P0303 are possibly spark plugs. They could be a coil pack but I'm leaning toward a spark plug problem because of the other two codes - they're indicating O2 sensor problems. If the O2 sensors are screwed up, the car reverts to preprogrammed, rich fuel maps that send excessive fuel through the engine. The reasoning is, if the ECU can't trust the O2 sensors to determine how much fuel to burn optimally, it'll pump a bunch of extra fuel through the engine to keep it safe. Having too little fuel (aka running lean) can destroy an engine, so the ECU plays it safe and runs rich (too much fuel) instead. The consequences of rich running are relatively minor compared to lean running, but can and do tend to create excessive carbon buildup on the catalytic converter and O2 sensors, as well as fouling spark plugs.

First thing to do though is to swap the wires on your coil packs and see if you end up with a misfire code for the same cylinder #3. If you do, then it's the plug or wire. If it moves, it's the coilpack. Replace whichever part is faulty. You'll probably need oxygen sensors too, before you can clear all the codes.

Posted on Sep 02, 2008

  • 373 Answers

SOURCE: 2005 dodge diesel codes!

Hi..
the Code P0340, Camshaft Position sensor problem or Loss signal.
The Code P0341, Camshaft Position sensor Intermitent Signal.

The First step you should do is : Locate the Camsahaft sensor,
Is located On Right Front of the Engine..
It use a 3 wires Connector.
1-- Pink/Yellow
2-- Brown/Orange
3-- Dark blue/Gray.

After you found it. Inspect the Connector. If is The connector in good condition.
Replace the Camshaft Position sensor...

Ok... I hope this help on your problem..
Thank you for use Fixya...

Posted on Sep 27, 2008

  • 19 Answers

SOURCE: 1999 vw jetta check engine light on

Do you mean the OBD II connector? If your car is an early 99 then it's a MKIII and it's located under a little door on the dash under the heater controls HERE. IF it's a late 99 model then it's a MKIV and it's under the dash at the far left corner, just above the hood release lever.

Posted on Feb 08, 2009

ghost4548
  • 776 Answers

SOURCE: 2001 Volkswagen Jetta Check Engine Code PO442

This is an Evaporative Emissions System code - indicates the computer has checked the system and concludes there is a leak in the system (small leak).. could simply be a loose fuel cap.

Posted on May 28, 2009

  • 3640 Answers

SOURCE: 1999 Chevrolet Malibu Code PO122 problem

po341 is camshaft position sensor A bank 1 ckt range/perf and po122 istps/pedal position sensor A curcuit low input this is throttle position switch on side of throttle body!

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 jetta running lights do not come on


I have a jetta 2004 and i got it check engine light, now i know what code's but i don't know what part's wrong on my car the code's 18613 if somebody knows please let's me know thanks

Jul 05, 2014 | 2000 Volkswagen Jetta TDI

1 Answer

I am getting codes P0135 and P0341 on my 02 VW Jetta, the car wont run, what would cause this?


code p0135 refers to a HO2S sensor 1 bank 1 heater control ---circuit malfunction- ===causes ---fuse --wiring and sensor
the other code p0341 would point to your problem It refers to camshaft position sensor(CMP) sensor A bank 1 --range / performance problem===causes --insecure sensor /rotor---air gap---wiring - CMP sensor
check that the rotor is fixed properly , that there is no dirt in the air gap and adjust the air gap. If it still plays up replace the sensor.

Feb 26, 2014 | Cars & Trucks

3 Answers

My jetta vwgives me this code p0341 i have done evrything that could possible be done to fix this problem an it still gives me this code wat can it be help thanks


If you are still getting the code,
have a look at this page for more information.
http://www.obd-codes.com/p0341

Feb 11, 2013 | Cars & Trucks

1 Answer

I cant figure out the problem troubleshooting code P0341


Camshaft position sensor. It should be on the front of the engine just ahead of the valve cover. You will see the connector for it there.

Mar 06, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

What do codes p0335 and p0341 mean on 1996 Cavalier?


when your engine went into that 5 second sputter,
your computer or "PCM" did not get a constant signal from the crank or cam sensors that the engine was running.
These two sensors tell the computer what RPM the engine is turning so it can adjust fuel and spark.

Nov 21, 2009 | 1996 Chevrolet Cavalier

3 Answers

1999 Chevrolet Malibu Code PO122 problem fault code in the emission test and P0341 fault code in emssion test.


po341 is camshaft position sensor A bank 1 ckt range/perf and po122 istps/pedal position sensor A curcuit low input this is throttle position switch on side of throttle body!

Jun 05, 2009 | 1999 Chevrolet Malibu

1 Answer

Check engine light is on


The cam shaft sensor is faulty. replace this sensor. the light will go off when this replacement is accomplished.

May 23, 2009 | 1996 Volkswagen Jetta

1 Answer

Jetta 2.0 2000


16826/P0442/001090 - EVAP Emission Control Sys: Small Leak Possible Symptoms
  • Malfunction Indicator Light (MIL) active
Possible Causes
  • Evaporative Emission (EVAP) System leaking
Possible Solutions
  • Check Evaporative Emission (EVAP) System Sealing
    • Check Fuel Cap

May 22, 2009 | 1999 Volkswagen Jetta

1 Answer

My 2003 volkswagen Jetta 1.8T won't start


Volks 2001 Jetta 1.8T
Engine light on and fails to start.
Codes P0341, P0328, P0171, P01297 what are this codes telling me??? HELLLPP!!!!

Apr 21, 2009 | Volkswagen Jetta Cars & Trucks

1 Answer

Monte carlo trouble code p0341


p0341 on a scanner means something is wromg with the camshaft position sensor have it checked

Dec 30, 2008 | 1997 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...