Question about 2006 Ford Five Hundred

Open Question

Removing a wiper arm on a ford 500 - 2006 Ford Five Hundred

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
kennyz195
  • 61 Answers

SOURCE: replace rear wiper arm

there is a cover at the base lift it up and then you have a nut. 10mm remove this and pull off the arm. sometime they get stuck and you will have to pry it up.

Posted on Apr 02, 2010

Ad
  • 9 Answers

SOURCE: 1996 ford ranger pickup-splash wiper motor replacement

YOUR VENT COVER SHOULD COME RIGHT OFF GIVING YOU ACESS TO THE WIPER MOTOR AND THE CLIP AND NUT THE CLIP IS VERY TRICKY TO PUT BACK ON BUT WITH COVER OFF YOU SHOULD NOT LOOSE THE CLIP IT WILL JUST FALL IN CAVITY UNDER NEATH WIPER ARM ASSEMBLY GOOD LUCK

Posted on Oct 23, 2008

bulldogchief
  • 388 Answers

SOURCE: Removing/replacing wiper motor in '93 Ford Ranger

You don't have to put the wipers in an upright position You can take the arms completely off. It's very easy to do, when you are looking at the base of the wiper arm, on the side closest to the windshield, at the base, there is a spring-loaded tab. Lift the arm on its hinge to where the arm is now pointing away from the windshield, pull the tab and the wiper arm will slide right off. Now you can access the linkage joints easily. Hope that helps!

Posted on Nov 09, 2009

  • 120 Answers

SOURCE: how do I change wiper blades on a Ford 500

This is a fairly simple job.
#1 Pull the wiper arm away from the vehicle.
#2 Turn the blade 90 degrees so that the blade and the arm make a 'capital T' shape.
#3 Pull the blade straight off of the arm.
#4 Install the new wiper blade so that it forms a ' T ' with the arm.
#5 Turn the blade back to the normal position in line with the arm.
#6 Ease the wiper arm and blade back against the windshield.
#7 You are done. Good luck

Posted on Jan 23, 2010

kayzack519
  • 226 Answers

SOURCE: i have a 2005 ford expidition. The rear wiper arm

the motor is probably shot. if you can hear it run and nothing happens, you can eliminate a power issue. U r better off going to a junk yard(they will pull it for you) and replace it. Its pretty simple. Hope it helps

Posted on Mar 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to have 'step-by-step' instructions for replacing the driver side windshield wiper arm on my 2000 Ford Explorer. Can you help me with this?


  • Turn your wipers off, using the stalk on the left side of your steering column. Turn your ignition off and remove the key.

  • 2

    Pull the wiper blade up to lift it to the service position. Pull the front part of the blade down to position it at an angle.

  • 3

    Pull back the lock pin on the center part of the wiper blade (where it connects to the wiper arm). This unlocks the blade from the wiper arm.

  • 4

    Grasp the blade on each side and pull it down (away from the extended wiper arm) to release it from the "U" clip.

  • 5

    Repeat the process for the other wiper blade, if desired. Removing the driver's side and passenger's side wiper blade is the same.

  • 6

    Install the new wiper blade. Open the lock pin on the new blade, and then insert it into the wiper arm "U" clip. Close the lock pin and lower the wiper blade to its normal position.

  • Jan 29, 2011 | Ford Explorer Cars & Trucks

    1 Answer

    Rpassenger side windshield wiper arm stopped moving, passenger side is still working


    Take a look at and remove the nut which holds the wiper arm down to the little axle/stub. Remove the arm and you will find that the inside barrel of the arm where it attached to the axle is stripped smooth, supposed to be serrated to hold to the axle's serrations. Be careful and do not pry on the glass when removing the arm. Find another wiper arm at a junk yard and replace yours. Make sure you take a good look at the replacement before you buy it. And note that the wiper arms for
    driver and passenger are different.

    Sep 18, 2010 | 1998 Ford F150 Regular Cab

    1 Answer

    I need to replace a windshield wiper motor on a 2000 ford focus not for sure how to do this


    remove the wiper arm L&R using the corresponding spanner.open the cowl plastic cover by removing the screws along the sides.upon removing the cover you can access the wiper motor and linkages.disconnect the connector and bolts and take it out in one piece more easier to replace

    Jan 14, 2010 | 2000 Ford Focus

    1 Answer

    How do I change wiper blades on a Ford 500


    This is a fairly simple job.
    #1 Pull the wiper arm away from the vehicle.
    #2 Turn the blade 90 degrees so that the blade and the arm make a 'capital T' shape.
    #3 Pull the blade straight off of the arm.
    #4 Install the new wiper blade so that it forms a ' T ' with the arm.
    #5 Turn the blade back to the normal position in line with the arm.
    #6 Ease the wiper arm and blade back against the windshield.
    #7 You are done. Good luck

    Jan 03, 2010 | 2006 Ford Five Hundred

    1 Answer

    Removing/replacing wiper motor in '93 Ford Ranger


    You don't have to put the wipers in an upright position You can take the arms completely off. It's very easy to do, when you are looking at the base of the wiper arm, on the side closest to the windshield, at the base, there is a spring-loaded tab. Lift the arm on its hinge to where the arm is now pointing away from the windshield, pull the tab and the wiper arm will slide right off. Now you can access the linkage joints easily. Hope that helps!

    Nov 09, 2009 | 1993 Ford Ranger SuperCab

    1 Answer

    Windshield wipers not working


    there are little tabs at the end of the arm where it attaches to the wiper trans. if you bend the arms up at the hinge and swing those tabs out the arms will stay up (a small screw driver can be used to move the tabs if they are stuck. A 1/8 screwdriver is a good choice, $4 at sears). once those tabs are out and the arms are holding themselves up just pull. you may need to rock them back and forth a bit but they should just pull off.

    To remove the wiper motor itself:
    1993 Aerostar/Ranger/Explorer
    1. Turn the wiper switch on. Turn the ignition switch on until the blades are straight up. Then, turn ignition off to keep them there.
    1. Disconnect battery and wiper motor electrical connector.
    1. Remove the right wiper arm and blade.
    1. Disconnect the negative battery cable.
    1. Remove the right pivot nut and allow the linkage to drop into the cowl.
    1. Remove the linkage access cover, located on the right side of the dash panel near the wiper motor.
    1. Reach through the access cover opening and unsnap the wiper motor clip.
    1. Push the clip away from the linkage until it clears the nib on the crack pin. Then, push the clip off the linkage.
    1. Remove the wiper linkage from motor crank pin.
    1. Remove nut and ground strap.
    1. Remove three attaching nuts from wiper motor. Remove the motor.
    (instructions copied direct from ford shop manual)

    Oct 04, 2009 | 1993 Ford Explorer Limited

    1 Answer

    The right wiper blade doesent move i need to get at the wiper mtor how do i do that ?


    Try removing the cowl by the wiper. Are you trying to remove the wiper blade or the motor?There's a pull pin underneath the wiper arm at the base where you can lift it up. Pull pin and give it a good jiggle to remove wiper arm

    Sep 30, 2009 | 1995 Ford Explorer

    1 Answer

    Removing windshield wiper assembly ford excursion


    Wiper Pivot Arm Removal and Installation
    1. Lift the windshield wiper pivot arm to the full upright position.
    1. Remove the windshield wiper pivot arm.
      1. Release the locking tab.
      1. Remove the windshield wiper pivot arm.
    52fed05.gif
    1. NOTE: During installation, it is necessary to pull the locking tab out to its full open (unlatched) position and hold while assembling the pivot arm onto the mounting arm and pivot shaft. Align the key on the pivot arm head with the keyway on the shafts. This will make sure the pivot arm is correctly aligned. If necessary, the key can be removed. To adjust wiper pivot arms, refer to Wiper Blade and Pivot Arm Adjustment in this section.
      To install, reverse the removal procedure.

    Jul 02, 2009 | 2005 Ford Excursion

    2 Answers

    Cant take off the windsheild wipers


    Here is the procedure to remove the wiper motor. It says to remove wipers by removing the nut covers then remove the wiper nuts. Is this what your talking about?
    If your talking about the wiper arms they just pop off at the swivel.
    Use this link for info on removing blade assy.
    http://www.autozone.com/az/cds/en_us/0900823d/80/04/f8/26/0900823d8004f826/repairInfoPages.htm

    Wiper Motor
    Removal & Installation
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Park the wiper pivot arms in the highest position on the glass.
    3. Disconnect the battery ground cable.
    4. Remove the wiper pivot arm nut covers.
    5. Remove the nuts and the wiper pivot arms.
    6. Remove the cowl top vent panels.
    7. Remove the four bolts, wiper mounting arm and wiper pivot shaft assembly.
    8. Disconnect the electrical connector.
    9. Remove the bolt and the windshield wiper motor operating arm from the motor.
    10. Remove the three bolts and remove the windshield wiper motor.
    11. To install, reverse the removal procedure.

    Jan 28, 2009 | 2005 Ford Taurus

    1 Answer

    1996 ford ranger pickup-splash wiper motor replacement


    YOUR VENT COVER SHOULD COME RIGHT OFF GIVING YOU ACESS TO THE WIPER MOTOR AND THE CLIP AND NUT THE CLIP IS VERY TRICKY TO PUT BACK ON BUT WITH COVER OFF YOU SHOULD NOT LOOSE THE CLIP IT WILL JUST FALL IN CAVITY UNDER NEATH WIPER ARM ASSEMBLY GOOD LUCK

    Oct 22, 2008 | 1997 Ford Ranger SuperCab

    Not finding what you are looking for?
    2006 Ford Five Hundred Logo

    Related Topics:

    354 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76848 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...