Question about 2003 Buick Regal

Open Question

Torque setting for axle nut on 2003 buick regal

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: signal bulb on 2003 buick regal

To change front turn signal –
open the hood; look in back of headlight; two white clips; pull straight up, and then whole headlight comes out including turn signal; it is all one unit; remove rubber cover, then you take bulb out of unit. Mechanism that bulb fits in will need to be turned clockwise (looking from the front) and pulled to get it out of the larger unit holding all lights. Be sure and put rubber cover back on before re-inserting the two white clips.

Posted on May 07, 2009

Ad
  • 61 Answers

SOURCE: Need the 2000 Buick LeSabre rear wheel Hub nut torque spec.

Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

Posted on Jul 24, 2009

johnjohn2
  • 5763 Answers

SOURCE: how to install front axle 99 buick regal

remove axle nut, remove nut on lower balljiont seperate control arm from spindle. pull back spindle and slide frt part of axle out of hub, then pry axle out of trany . good luck.

Posted on Nov 02, 2009

GMJunkie
  • 74 Answers

SOURCE: Need Cylinder head bolt torque specs and sequence

  1. Install the cylinder head gasket. Ensure the arrows point towards the front of the engine. The left cylinder head gasket has the letter L stamped next to the arrow.
  2. Notice
  3. This bolt is designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do not use a bolt that is stronger in this application. If the correct bolt is not used, the parts will not be tightened correctly. The system or the components may be damaged.

  4. Install the cylinder head.
  5. Install new cylinder head bolts. Tighten
    Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.
  6. Use the J 36660-A to rotate each cylinder head bolt 120 degrees in sequence. Use the J 36660-A to rotate the four center cylinder head bolts an additional 30 degrees in sequence. Refer to Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

d429947.gif

Posted on Mar 10, 2010

fixitriteman
  • 431 Answers

SOURCE: I have a 2003 Buick Regal LX -after I start the

It could be the park safety that works off of your brake switch , may need to be replaced , it is under the dash hooks to brake lever, don't know if you can adjust it or just hook it back up try holding more pressure on brake , please let us know what happens , Thank You .

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Buick lasabre when driving slow I can hear cracking noise left front tire I replace the HUD assembly and put new tires on front


Make sure wheel nuts are tight and torqued properly. Inspect hub assembly bolts and axle nut for proper torque as well

Jul 12, 2015 | Buick Cars & Trucks

1 Answer

What is the torque spec for the front center axle nut on a 2003 tahoe?


The torque specs.are for 15k series trucks is 155 ft.lbs.For 25/35 series it`s 133 ft.lbs.Hope this helps.Good luck.

Dec 03, 2011 | 2003 Chevrolet Silverado 1500

3 Answers

I cant get the front hub assembly off my 03 buick rendevous


Items/Tools needed:

35mm or 1 3/8" axle socket
3/4 or 19mm socket for lug nuts or lug wrench
15mm socket for brake caliper and bracket
13mm socket for wheel bearing bolts (extentions as well)
Breaker bar or impact wrench to remove lug nuts and axle nut (Note: Do not use impact driver to install axle nut).
Torque wrench for axle nut
Hub puller - Optional
Hammer

Directions

1. Jack the appropriate side of the car up. Make sure the rear wheels are blocked and/or set the parking brake. Use a jackstand to support vehicle at subframe for safety.
2. Remove wheel.
3. Remove brake caliper and bracket.
4. Remove rotor.
5. Using 35mm axle socket, remove axle nut, turn counterclockwise. You will either need an impact or a long breaker bar. They are installed with a lot of torque or may be rusted out or corrroded.
6. Push the axle back as far as possible. It won't come all the way out or through the hub, but will become loose. You can either get a tool that will push it out like a hub puller, or just use a hammer making sure not to hit the axle shaft threads and damage them. Put the axle nut back on the axle shaft so it is flush with the top. Then place 35mm axle nut socket on the axle nut and tap on the 35mm socket with the hammer not the threads on the axle shaft spline.
7. Disconnect the wheel sensor connector and then remove hub side connector from the bracket (unclip).
8. Take a 13mm socket with extensions as needed and remove the 3 bolts on the backside of the bearing around the axle. Be sure to use PBBlaster to help loosen the bolts.
9. The hub/bearing should come loose without need needing a hub puller. Be sure to note the sheet metal spacer between the hub and spindle with also has the bracket for the wheel sensor connector.
10. Double check both parts (hubs) to make sure they match.
11. Lube the axle shaft splines with good quality bearing grease before installing the hub. Clean off any old grease and crud first.
12. Install the hub assembly with the wires from the bearing at the bottom. Line up hub splines with axle shaft splines and push in on hub. Note: Don't forget that sheet metal plate between the spindle and wheel bearing. Note: Make sure the wheel sensor wires don't get pinched by the axle shaft.
13. Install the 3 13mm bolts to 96ft lbs. Service manual recommends replacing with new ones. Some hubs like AC Delco will come with new bolts which have threadlocker.
14. Install the axle nut. As tightened down it will pull the driveshaft the rest of the way in. Torque axle nut to GM specs of 159 ft-lbs or the figure specified by the hub manufacturer. It is recommended to use a new axle nut but not necessary.
15. Install the rotor, brackets and caliper. Torque caliper bracket bolts to 137 ft-lb and caliper pin bolts to 63 ft-lb.
16. Install the connector to the sheet metal bracket and reconnect both connectors.
17. Install the wheel. Torque lug nuts in a star pattern at 100 ft-lbs each.
18. Road test car and ensure any ABS and TRAC OFF light are off.

Sep 18, 2011 | 2003 Buick Rendezvous

1 Answer

How do I replace drivers side front axle on a 2003 Ford Escape ?


remove the right front wheel. remove the axle nut. remove the ball joint bolt and nut. remove the ball joint from the knuckle. drive the axle out of the hub. remove the 2 carrier bearing nuts. pull the axle out. make sure you torque all bolts and nuts.

Sep 17, 2011 | 2003 Ford Escape

1 Answer

2000 buick lesabre axle nut torque



  • You don't need to use a torque speck really on an axle bolt. Just snug it by hand real good and make sure to stick a new cotter pin in through the axle and axle bolt to prevent the bolt from self un-threading. That all I have really ever done.

  • Hope this helps and thank you for using FixYa.

Regards, Tony

Aug 01, 2011 | 2000 Buick LeSabre

1 Answer

Need torque setting for rear hub assembly on 2003 Buick Rendezvous


BEARING TO HUB TO THE AXLE BEAM BOLTS TORQUE IS 63 FT LBS.FOR DRUM BRAKES 96 FT LBS WITH DISC BRAKES.

Apr 18, 2010 | 2003 Buick Rendezvous

1 Answer

Bolt torque for front hub on 2003 buick regal


120 foot pounds using Loctite on the threads

Apr 02, 2010 | 2003 Buick Regal

1 Answer

How to install front axle 99 buick regal (right front)


remove axle nut, remove nut on lower balljiont seperate control arm from spindle. pull back spindle and slide frt part of axle out of hub, then pry axle out of trany . good luck.

Nov 02, 2009 | 1999 Buick Regal

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
2003 Buick Regal Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...